Indesit WIE 107 XS (EX) Manualul utilizatorului

Marca: Indesit

Model: WIE 107 XS (EX)

Categorie: Mașini de spălat

Tip: Manualul utilizatorului

English,1

Contents

Installation, 2-3

Unpacking and levelling, 2

Electric and water connections, 2-3

The first wash cycle, 3

Technical details, 3

Washing machine description, 4-5

Control panel, 4

Display, 5

MEMO Programme, 5

Starting and Programmes, 6

Briefly: how to start a programme, 6

Programme table, 6

Personalisations, 7

Setting the spin cycle, 7

Setting the Delay Timer, 7

Setting the temperature, 7

Functions, 7

Detergents and laundry, 8

Detergent dispenser, 8

Bleach cycle, 8

Preparing your laundry, 8

Special items, 8

Precautions and advice, 9

General safety, 9

Disposal, 9

Saving energy and respecting the environment, 9

Care and maintenance, 10

Cutting off the water or electricity supply, 10

Cleaning your appliance, 10

Cleaning the detergent dispenser, 10

Caring for your appliance door and drum, 10

Cleaning the pump, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for Assistance, 12

WASHING MACHINE

WIE 107 XS

Instructions for use

Magyar,2 5

Românã,13

Èeský,37

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the 4

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Use the plug provided to seal the three holes

where the plug was housed, situated on the lower

right-hand side on the rear of your appliance.

6. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the

hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Installation

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (on the right);

 the supply voltage is included within the values i

ndicated on the Technical details table

(on the right);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

65 - 100 cm

Technical details

Model

WIE 107 XS

Dimensions

59.5 cm wide

85 cm high

53.5 cm deep

Capacity

from 1 to 5 kg

Electric

connections

voltage 220/230 Volts 50 Hz

maximum absorbed power 1850 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 46 litres

Spin speed

up to 1000 rpm

Control

programmes

according to

IEC456 directive

programme 2; temperature 60°C;

run with a load of 5 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

Control panel

Washing machine description

Control knob

Display

Detergent dispenser

SPIN

button

TEMPERATURE

button

START/STOP

button

START/RESET

button

Detergent dispenser to add detergent and fabric

softener (see page 8).

SPIN button to adjust the spin speed or exclude it

altogether (see page 7).

DELAY TIMER button to delay the start of the set

programme for a maximum period of 24 hours

(see page 7).

TEMPERATURE button to adjust the wash tempe-

rature (see page 7).

Display to programme the washing machine and

follow the wash cycle progress (see opposite page).

FUNCTION buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

START/RESET button to start the programmes or

cancel any incorrect settings.

START/STOP button to turn the washing machine

on and off.

Control knob to select the wash programmes.

The knob stays still during the cycle.

DELAY TIMER

button

FUNCTION

Buttons

Display

In addition to being a practical tool to programme your appliance (see page 7), the display provides useful

information concerning the wash cycle.

Once you have pressed the START/RESET button to

start the programme, the display will indicate the

amount of time left until the end of the wash cycle. If

a delayed start has been set (using the Delay Timer,

see page 7), the delay time will be indicated on the

display.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Door lock:

If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid

any damages, wait for the symbol to switch itself off before you open the appliance door.

At the end of the programme, the word END is displayed.

 In the event of an anomaly, an error code will appear, such as: F-01, which should be communicated to the

Service Centre (see page 12).

"MEMO" Programme

This programme allows you to store your favourite or most-used wash cycle.

All you have to do is set the desired programme and, once it has started, turn the KNOB to position

; the

wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.

Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position

; you will be able to

see the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to

modify them but this variation will only be valid for the programme in progress and it will not be stored in the

"MEMO" cycle.

If you want to store a new wash cycle, repeat the above-mentioned operations.

Type of fabric and

degree of soil

Programmes

Te m p e -

rature

Detergent

Fabric

softener

Stain removal

option/bleach

Cycle

length

(m inute s)

Description of wash cycle

pre-

wash

Standard

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C   

135

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C  

Delicate/

Traditional

125

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and fast

colours

60°C  

Delicate/

Traditional

110

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and

delicate colours

40°C  

Delicate/

Traditional

105

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and

delicate colours (shirts,

jumpers, etc.)

40°C  

Delicate/

Traditional

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled fast colours

(baby linen, etc.)

°C

  Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Heavily soiled fast colours

(baby linen, etc.)

40°C   Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Wool

40°C  

Wash cycle, rinse cycles

anti-

crease and delicate spin cycle

Very delicate fabrics

(curtains, silk, viscose, etc.)

30°C  

Wash cycle, rinse cycles, anti-

crease or draining cycle

Time 4 you

Heavily soiled whites and fast

colours

60°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and

delicate colours (shirts,

jumpers, etc.)

40°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Delicate colours (all types of

slightly soiled garments)

°C



Wash cycle, rinse cycles,

delicate spin cycle

Delicate colours (all types of

slightly soiled garments)

30°C   30

Wash cycle, rinse cycles and

delicate spin cycle

Sport

Sports shoes

(MAX. 2 pairs)

°C

 50

Cold wash (without detergents),

wash cycle, rinse cycles, and

delicate spin cycle

Fabrics for sportswear

(Tracksuits, shorts, etc.)

30°C   60

Wash cycle, rinse cycles,

intermediate and final spin cycles

MEMO

Allows for any wash cycle to be stored

PARTIAL PROGRAMMES

Rinse 

Delicate/

Traditional

Rinse cycles and spin cycle

Spin Draining and spin cycle

Drain Draining

Starting and Programmes

Programme table

Notes

-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.

-For programme 12 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts

30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

Briefly: starting a programme

1. Turn the washing machine on by pressing button .

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the knob to the desired programme. The

estimated duration of the selected programme is

displayed. The temperature and spin speed are

automatically set according to the programme

(to change them, see page 7).

4. Select any functions (see page 7).

5. Add the detergent and any fabric softener

(see page 8).

6. Start he programme by pressing the START/RESET

button.

To cancel it, keep the START/RESET button

pressed for at least 2 seconds.

7. When the programme has ended, the word END is

displayed. Take out your laundry and leave the

appliance door ajar to allow the drum to dry

thoroughly.

8. Turn the washing machine off by pressing button

(see page 5).

Function Effect Comments

Enabled with

programmes:

Stain

removal

Bleaching cycle

designed to

remove the

toughest stains.

Please remember to pour the bleach into extra compartment 4

(se

e page 8)

This function is incompatible with the EASY IRON function.

2, 3, 4,

Rinse cycle.

Extra Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 7,

8, 9, 11, 12,

Rinse cycle.

Easy iron

This option

reduces the

amount of

creasing on

fabrics, making

them easier to

iron.

When this function is set, programmes 4, 5, 6 will end, with the

laundry left to soak (Anti-crease), and the relative button flashes:

- to conclude the cycle, press the START/RESET button or the

EASY IRON button;

- to run the draining cycle alone, set the knob to the relative

symbol and press the START/RESET button.

This function is incompatible with the STAIN REMOVAL function.

3, 4, 5, 6, 7, 8,

9, Rinse

cycle.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Personalisations

Setting the temperature

If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature

needs to be regulated, a fixed

appears. Press button and the maximum temperature allowed for the

programme set will be displayed and the

icon flashes. Press it again and the temperature lowers until it

reaches OFF, which indicates a cold wash cycle (press it again to go back to the maximum value); stop on the

desired value, after approximately 2 seconds the setting is accepted: the symbol

remains fixed.

The temperature adjustment is enabled with all wash programmes.

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

If you set a function that is incompatible with another function you selected previously, only the last one

selected will be enabled.

Setting the spin cycle

If, when the appliance is switched on, the KNOB is positioned

on a programme with a spin cycle, a fixed

appears. Press

button

and the maximum spin speed allowed for the

programme set will be displayed, and the

icon flashes. Press

it again and the values lower until they reach OFF, which

indicates that the spin cycle has been excluded (press it again

to go back to the maximum value); stop on the desired speed,

after approximately 2 seconds the setting is accepted: the

symbol

remains fixed.

The spin cycle setting is enabled with all the programmes

except for 6 and the Draining cycle.

Setting the Delay Timer

Press the button and you will see the word OFF on the

display, while the relative symbol flashes.

Press the button again and "1h" appears, that is, a delay of one

hour (this can reach up to 24h); stop on the "desired" delay;

after approximately 2 seconds the setting is accepted, following

which, the time for the set programme appears on the display

and the symbol

remains on.

If you now press the START/RESET button, the set "delay"

appears; this decreases every hour until the start of the cycle.

In this phase, the "delay" can only be modified by decreasing it.

The Delay Timer regulation is enabled with all programmes.

FUNCTION buttons

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

Before pouring in the detergent, make sure that

extra compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

extra compartment 4: Bleach

 Do not use hand wash detergent because it may

form too much foam.

Bleach cycle

 Traditional bleach should be used on sturdy

white fabrics, and delicate bleach for coloured

fabrics, synthetics and for wool.

Place extra

compartment 4,

provided, into

compartment 1.

When pouring in the

bleach, be careful not to

exceed the "max" level

indicated on the central

pivot (see figure).

To run the bleach cycle alone, pour the bleach into extra

compartment 4 and set the Rinse programme

To bleach during a wash cycle, pour in the detergent

and fabric softener, set the desired programme and

enable the Stain removal function (see page 7).

The use of extra compartment 4 excludes the

possibility of using the pre-wash cycle.

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 5 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 6

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1 kg.

Detergents and laundry

Precautions and advice

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

 The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 Disposing of an old washing machine:

before scrapping your appliance, cut the power

supply cable and remove the appliance door.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your washing machine only needs less

than half the amount of water to get the best

results: an objective reached to respect the

environment.

Saving on detergent, water,

energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

 The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

 Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures. A

programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

The Delay Timer option (see page 7) helps to

organise your wash cycles accordingly.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem

can't easily be solved by consulting the following list.

Troubleshooting

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water (The wording H2O is

displayed).

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to

make contact.

 There has been a power failure.

 The appliance door is not shut properly (the word DOOR is

displayed).

 The

button has not been pressed.

 The START/RESET button has not been pressed.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Timer, see page 7).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 3).

 The free end of the hose is underwater (see page 3).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 6).

 The Easy iron option is enabled: to complete the programme, press

the START/RESET button (see page 7).

 The drain hose is bent (see page 3).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 2).

 The washing machine is not level (see page 2).

 The washing machine is closed in between furniture cabinets and

the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 10).

 The drain hose is not secured properly (see page 3).

 The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

 You used too much detergent.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 11);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service

Românã

Sumar

Instalare, 14-15

Scoaterea din ambalaj ºi nivelarea, 14

Legãturi hidraulice ºi electrice, 14-15

Primul ciclu de spãlare, 15

Date tehnice, 15

Descrierea maºinii de spãlat, 16-17

Panoul de control, 16

Display-ul, 17

Program MEMO, 17

Pornire ºi Programe, 18

Pe scurt: pornirea unui program, 18

Tabel de programe, 18

Personalizãri, 19

Reglarea centrifugei, 19

Reglarea delay timerului, 19

Reglarea temperaturii, 19

Funcþii, 19

Detergenþi ºi rufe albe, 20

Sertarul detergenþilor, 20

Ciclu de albire, 20

Prepararea rufelor, 20

Rufe deosebite, 20

Precauþii ºi sfaturi, 21

Protecþie generalã, 21

Aruncarea reziduurilor, 21

Protecþia ºi respectarea mediului înconjurãtor, 21

Întreþinere ºi îngrijire, 22

Oprirea apei ºi a curentului electric, 22

Curãþarea maºinii de spãlat, 22

Curãþarea sertarului pentru detergenþi, 22

Îngrijirea hubloului ºi a coºului, 22

Curãþarea pompei, 22

Controlarea tubului de alimentare cu apã, 22

Anomalii ºi remedii, 23

Asistenþã, 24

Înainte de a lua legãtura cu Asistenþa, 24

MAªINÃ DE SPÃLAT RUFE

WIE 107 XS

INSTRUCÞIUNI DE FOLOSIRE

 Este important sã se pãstreze acest manual

pentru a-l putea consulta în orice moment. În caz

de vânzare, de cesiune sau de schimbare a

locuinþei, acesta trebuie sã rãmânã împreunã cu

maºina de spãlat pentru a informa noul proprietar

cu privire la funcþionare ºi la respectivele

avertismente.

 Citiþi cu atenþie instrucþiunile: veþi gãsi informaþii

importante cu privire la instalare, la folosire ºi la

siguranþã.

Scoaterea din ambalaj ºi nivelarea

Scoaterea din ambalaj

1. Scoaterea din ambalaj a maºinii de spãlat.

2. Controlaþi ca maºina de spãlat sã nu fi fost

deterioratã în timpul transportului. Dacã este deterioratã

nu o conectaþi ºi luaþi legãtura cu cine v-a vândut-o.

3. Scoateþi cele 4

ºuruburi de protecþie

pentru transport ºi

cauciucul cu respectivul

distanþator, situate în

partea posterioarã (vezi

figura).

4. Închideþi orificiile cu dopurile din plastic aflat în dotare.

5. Închideþi cu dopul aflat în dotare cele trei orificii în care

se afla fiºa, situate în partea posterioarã, jos în dreapta.

6. Pãstraþi toate piesele: pentru cazul în care maºina de

spãlat va trebui sã fie transportatã, piesele vor trebui

montante din nou.

 Ambalajele nu constituie jucãrii pentru copii

Nivelare

1. Instalaþi maºina de spãlat pe un paviment plan ºi

rigid, fãrã a o sprijini de ziduri, mobilã sau altceva.

2. Dacã podeaua nu este

perfect orizontalã,

compensaþi neregularitãþile

deºurubând sau

înºurubând picioruºele

anterioare (vezi figura);

unghiul de înclinare,

mãsurat pe planul de

lucru, nu trebuie sã

depãºeascã 2°.

O nivelare precisã conferã stabilitate maºinii ºi

evitã vibraþii, zgomote ºi deplasãri pe timpul

funcþionãrii. În cazul mochetelor sau a unui covor,

reglaþi picioruºele astfel încât sã menþineþi sub

maºina de spãlat un spaþiu suficient pentru

ventilare.

Legãturi hidraulice ºi electrice

Conectarea tubului de alimentare cu apã

1. Introduceþi garnitura

A în extremitatea

tubului de alimentare ºi

înºurubaþi-l la un robinet

de apã rece cu gura

filetatã de ¾ gaz (vezi

figura).

Înainte de conectare,

lãsaþi apa sã curgã

pentru a se limpezi.

2. Conectaþi tubul de

alimentare la maºina

de spãlat,

înºurubându-l la

respectiva prizã de

apã, în partea

posterioarã, sus în

dreapta (vezi figura).

3. Fiþi atenþi ca tubul sã nu fie nici curbat nici

îndoit.

 Presiunea apei trebuie sã fie cuprinsã în valorile

tabelului Date tehnice (vezi pagina alãturatã).

 Dacã lungimea tubului de alimentare nu este

suficientã, adresaþi-vã unui magazin specializat sau

unui tehnician autorizat.

Instalare

Conectarea tubului de evacuare

Conectaþi tubul de

evacuare, fãrã a-l îndoi,

la o conductã de

evacuare sau la o gurã

de evacuare în zid,

situate între 65 ºi 100

cm de pãmânt;

sau sprijiniþi-l pe

marginea unei chiuvete

sau a unei cãzi, legând

ghidul aflat în dotare,

de robinet (vezi figura).

Extremitatea liberã a

tubului de evacuare nu

trebuie sã rãmânã

cufundatã în apã.

 Nu este recomandabilã folosirea tuburilor de

prelungire; dacã este indispensabil, tubul de

prelungire trebuie sã aibã acelaºi diametru cu tubul

original ºi nu trebuie sã depãºeascã 150 cm.

Legãtura electricã

Înainte de a introduce fiºa în priza de curent,

asiguraþi-vã ca:

 priza sã fie cu împãmântare ºi conform

prevederilor de lege;

 priza sã poatã suporta sarcina maximã de

putere a maºinii, indicatã în tabelul cu Date

tehnice (vezi alãturi);

 tensiunea de alimentare sã fie cuprinsã în valorile

indicate în tabelul cu Date tehnice (vezi alãturi);

 priza sã fie compatibilã cu fiºa maºinii de spãlat.

În caz contrar înlocuiþi priza sau fiºa.

 Maºina de spãlat nu trebuie instalatã afarã, nici chiar

în cazul în care spaþiul este adãpostit, deoarece este

foarte periculoasã expunerea maºinii la ploi ºi furtuni.

 Dupã instalarea maºinii de spãlat, priza de curent

trebuie sã fie uºor accesibilã.

 Nu folosiþi prelungitoare ºi prize multiple.

 Cablul nu trebuie sã fie îndoit sau comprimat.

 Cablul de alimentare trebuie sã fie înlocuit doar

de tehnicieni autorizaþi.

Atenþie! Producãtorul îºi declinã orice

responsabilitate pentru cazul în care aceste norme

nu se respectã.

Primul ciclu de spãlare

Dupã instalare, înainte de folosire, efectuaþi un ciclu

de spãlare cu detergent ºi fãrã rufe, selectând

programul la 90°C fãrã prespãlare.

AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere

65 - 100 cm

Date tehnice

Model

WIE 107 XS

Dimensiuni

lãrgime 59,5 cm

înãlþime 85 cm

profunzime 53,5 cm

Capacitate

de la 1 la 5 kg

Legãturi electrice

tensiune 220/230 Volþi 50 Hz

putere maximã absorbitã 1850 W

Legãturi hidrice

presiune maximã 1 MPa (10 bari)

presiune minimã 0,05 MPa (0,5 bari)

capacitatea cuvei 46 litri

Viteza de centrifugare

pânã la 1000 de rotaþii pe minut

Programe de control

pe baza normei

IEC456

programul 2; temperatura 60

efectuatã cu 5 kg de rufe.

Acest aparat este conform cu

urmãtoarele Directive Comunitare:

- 73/23/CEE din data de 19/02/73

(Tensiuni Joase) ºi modificãri succesive

- 89/336/CEE din data de 03/05/89

(Compatibilitate Electromagneticã) ºi

modificãri succesive

Panoul de control

Descrierea maºinii de spãlat

Selectorul

Display-ul

Sertarul detergenþilor

Butonul

CENTRIFUGÃ

Butonul

TEMPERATURÃ

Butonul

PORNIRE/OPRIRE

Butonul

START/RESET

Sertarul detergenþilor pentru a încãrca detergenþi

ºi aditivi (vezi pag. 20).

Butonul CENTRIFUGÃ pentru reglarea vitezei de

centrifugare pânã la excluderea acesteia

(vezi pag. 19).

Buton DELAY TIMER pentru a întârzia pornirea

programului selectat cu maxim 24 de ore

(vezi pag. 19).

Butonul TEMPERATURÃ pentru modificarea

temperaturii de spãlare (vezi pag. 19).

Display-ul pentru programarea maºinii de spãlat ºi

efectuarea avansãrii ciclurilor de spãlare (vezi

pagina alãturatã).

Taste FUNCÞIONARE: pentru a selecta funcþiile

disponibile. Butonul corespunzãtor funcþiei

selectate va rãmâne aprins.

Butonul START/RESET pentru pornirea

programelor sau anularea a ceea a fost selectat

greºit.

Butonul PORNIRE/OPRIRE pentru pornirea ºi

stingerea maºinii de spãlat.

Selectorul pentru alegerea programelor.

Pe durata programului selectorul rãmâne ferm.

Butonul

DELAY TIMER

Taste

FUNCÞIONARE

AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere

Display-ul

În afarã de faptul cã este un instrument util pentru programarea maºinii (vezi pag. 19), displayul furnizeazã

informaþii cu privire la ciclul de spãlare.

Dupã apãsarea butonului START/RESET pentru a

porni programul, pe display este cronometratã

durata rezidualã pânã la iniþierea programului de

spãlare ales. În cazul în care iniþierea programului de

spãlare dupã un anumit interval de timp (Delay

Timer, vezi pag. 19), aceasta va fi vizualizatã.

Hublou blocat:

Simbolul aprins indicã faptul cã hubloul este blocat pentru a împiedica deschideri întâmplãtoare.

Pentru a evita daunele ce pot deriva dintr-o funcþionare defectuoasã, este necesar sã aºteptaþi ca simbolul sã

se stingã înainte de a deschide hubloul.

La sfârºitul programului se vizualizeazã cuvântul END.

 În caz de anomalie apare un cod de eroare, de exemplu: F-01, de transmis Asistenþei Tehnice (vezi pag. 24).

Program MEMO

Acest program permite memorizarea ciclului de spãlare preferat sau cel mai utilizat.

Este suficient sã se selecteze programul dorit ºi dupã pornire sã se roteascã SELECTORUL pe poziþia

automat ciclul va fi memorizat iar pe display va apãrea scris MEMO intermitent timp de câteva secunde.

Dupã aceea va fi posibilã pornirea unui ciclu MEMO doar prin rotirea SELECTORULUI la poziþia

; se vor

putea vizualiza valorile de temperaturã/centrifugã/delay timer apãsând pe butoanele corespunzãtoare, se vor

putea chiar ºi modifica însã aceastã variaþie va fi valabilã doar pentru programul în curs ºi nu va fi memoratã în

ciclul MEMO.

Dacã se doreºte memorarea unui nou ciclu de spãlare, repetaþi operaþiunile indicate mai sus.

Tipul de þesãturã ºi de murdãrie Programe

Tempe-

raturã

Detergent

A ditiv

înm uiere

Opþiune

Antipatã /

Decolorant

Durata

ciclului

(minute)

Descrierea ciclului de spãlare

presp. Spãl.

Standard

Albe extrem de murdare

(cearceafuri, feþe de masã, etc.)

90°C

 

135

Prespãlare, spãlare, clãtiri,

centrifugi intermediare ºi finale

Albe extrem de murdare

(cearceafuri, feþe de masã, etc.)

90°C



Delicatã /

Tradiþionale

125

Spãlare, clãtiri, centrifugi

intermediare ºi finale

Albe ºi colorate rezistente foarte

murdare

60°C



Delicatã /

Tradiþionale

110

Spãlare, clãtiri, centrifugi

intermediare ºi finale

Albe ºi colorate delicate foarte

murdare

40°C



Delicatã /

Tradiþionale

105

Spãlare, clãtiri, centrifugi

intermediare ºi finale

Albe puþin murdare ºi culori

delicate (cãmãºi, bluze, etc.)

40°C



Delicatã /

Tradiþionale

Spãlare, clãtiri, centrifugi

intermediare ºi finale

Culori rezistente foarte murdare

(scutece pentru noi nãscuþi, etc.)

°C

Delicatã

Spãlare, clãtiri, antiºifonare sau

centrifugare delicatã

Culori rezistente foarte murdare

(scutece pentru noi nãscuþi, etc.)

40°C

Delicatã

Spãlare, clãtiri, antiºifonare sau

centrifugare delicatã

Lânã

40°C



Spãlare, clãtiri

antiºifonare ºi

centrifugare delicatã

Þesãturi foarte delicate

(perdele, mãtase, vâscozã, etc.)

30°C



Spãlare, clãtiri, antiºifonare sau

scurgere

Timp pentru tine

Albe ºi colorate rezistente foarte

murdare

60°C



Spãlare, clãtiri, centrifugi

intermediare ºi finale

Albe puþin murdare ºi culori

delicate (cãmãºi, bluze, etc.)

40°C



Spãlare, clãtiri, centrifugi

intermediare ºi finale

Culori delicate (rufe de toate

tipurile puþin murdare)

°C



Spãlare, clãtiri ºi centrifugare

delicatã

Culori delicate (rufe de toate

tipurile puþin murdare)

30°C

 30

Spãlare, clãtiri ºi centrifugare

delicatã

Sport

Încãlþãminte sportivã

(

MAX 2 perechi.

)

°C

 50

Spãlare la rece (fãrã detergent),

spãlare, clãtiri ºi centrifugã delicatã

Þesãturi pentru îmbrãcãminte sportivã

(Treninguri, chiloþi de gimnasticã, etc.

30°C

 60

Spãlare, clãtiri, centrifugi

intermediare ºi finale

MEMO

Permite memorarea oricãrui tip de spãlare

PROGRAME PARÞIALE

Clãtire 

Delicatã /

Tradiþionale

Clãtiri ºi centrifugare

Centrifugare Descãrcare apã ºi centrifugare

Descãrcare Descãrcare

Pornire ºi Programe

Tabel de programe

Pe scurt: pornirea unui program

1. Porniþi maºina de spãlat apãsând butonul .

2. Introduceþi rufele ºi închideþi hubloul.

3. Selectaþi cu ajutorul selectorului programul dorit.

Pe display va apãrea timpul estimat.

Temperatura ºi centrifuga se selecteazã automat

pe baza programului (pentru a le modifica vezi

pag. 19).

4. Selectaþi eventuale funcþii (vezi pag. 19).

5. Vãrsaþi detergenþi ºi aditivi (vezi pag. 20).

6. Porniþi programul apãsând butonul START/

RESET.

Pentru a anula þineþi apãsat butonul START/

RESET timp de cel puþin 2 secunde.

7. La sfârºitul programului va apãrea scris END.

Scoateþi rufele ºi lãsaþi hubloul întredeschis

pentru a se putea usca coºul.

8. Închideþi maºina de spãlat apãsând butonul

Note

-Pentru programele 7 - 8 este recomandabil sã nu se depãºeascã o cantitate de rufe de 3,5 kg.

-Pentru programul 12 este recomandabil sã nu se depãºeascã o cantitate de rufe de 2 kg.

-Antiºifonare-vezi calcã mai uºor, pagina alãturatã. Datele specificate în tabel au valoare indicativã.

Program special

Zilnic 30 (programul 10 pentru materiale sintetice) este studiat pentru a spãla rufe puþin murdare într-un

interval scurt de timp: dureazã doar 30 de minute economisindu-se energie ºi timp. Selectând programul

(10 la 30°C) este posibilã spãlarea împreunã a þesãturilor de diverse tipuri (excluse lâna ºi mãtasea) cu o

încãrcãturã maximã de 3 kg. Se recomandã folosirea detergentului lichid.

(vezi pag. 17).

Personalizãri

AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere

Reglarea centrifugei

Dacã la pornirea maºinii, SELECTORUL este poziþionat pe un

program care prevede centrifuga, icoana

apare fixã. Apãsând

pe butonul

se vizualizeazã viteza maximã permisã a

centrifugii pentru programul selectat iar icoana

semnalizeazã. Apãsând din nou valorile coboarã pânã la OFF,

ceea ce indicã excluderea centrifugii (apãsaþi din nou pentru a

reveni la valoarea cea mai mare); opriþi-vã la valoarea doritã,

dupã circa 2 secunde selecþia se acceptã: simbolul

rãmâne

fix. Reglarea centrifugei este activã pentru toate programele cu

excepþia programului 6 ºi a evacuãrii.

Reglarea delay timerului

Apãsând pe butonul pe display se vizualizeazã scris OFF

iar simbolul respectiv se ilumineazã intermitent.

Apãsând din nou pe buton apare 1h adicã întârziere de o orã

ºi aºa mai departe pânã la 24h; opriþi-vã la întârzierea doritã,

dupã circa 2 secunde selecþia se acceptã; dupã aceea pe

display se vizualizeazã timpul prevãzut pentru programul

selectat iar simbolul

rãmâne aprins.

Apãsând pe butonul START/RESET apare din nou valoarea

întârzierii selectate care scade la fiecare orã pânã la pornirea ciclului; în aceastã fazã se poate modifica

valoarea întârzierii doar micºorând-o. Reglarea Delay Timerului este activã cu toate programele.

Reglarea temperaturii

Dacã la pornirea maºinii, SELECTORUL este poziþionat pe un program care prevede reglarea temperaturii,

icoana

apare fixã. Apãsând pe butonul se vizualizeazã temperatura maximã permisã pentru programul

selectat iar icoana

semnalizeazã. Apãsând din nou, temperatura coboarã pânã la OFF, care indicã spãlarea

la rece (apãsaþi din nou pentru a reveni la valoarea cea mai mare); opriþi-vã la valoarea doritã, dupã circa 2

secunde selecþia se acceptã: simbolul

rãmâne fix.

Reglarea temperaturii este activã cu toate programele de spãlare.

Funcþii

Diferitele funcþii de spãlare prevãzute pentru maºina de spãlat permit obþinerea unor rezultate excepþionale (o

calitate îmbunãtãþitã a spãlãrii-rufe curate, etc.). Pentru a activa aceste funcþii, procedaþi astfel:

1. apãsaþi butonul aferent funcþiei dorite, þinând cont de informaþiile conþinute în tabelul de mai jos;

2. aprinderea butonului respectiv indicã faptul cã funcþia respectivã a fost activatã.

Notã: Intermitenþa rapidã a butonului indicã faptul cã funcþia respectivã nu este selecþionabilã pentru programul ales.

În cazul în care va fi selectatã o funcþie incompatibilã cu cea selectatã mai înainte, doar ultima aleasã va rãmâne activã.

Funcþii Efect Note pentru folosire

Activã cu

programele:

Antipatã

Ciclu de decolorare

adecvat pentru

eliminarea petelor

mai rezistente.

A se vãrsa decolorantul în sertarul adiþional 4

(a se vedea pag. 20

)

În acest moment nu puteþi utiliza funcþia CALCÃ MAI UªOR.

2, 3, 4,

Clãtiri.

Extra

Clãtire

Mãreºte eficacitatea

clãtirii.

Se recomandã cu maºina plinã sau cu doze elevate de detergent.

1, 2, 3, 4,

7, 8, 9, 11,

12, Clãtiri.

Calcã mai

uºor

Reduce pliurile la

þesãturi facilitând

cãlcarea.

Selectând aceastã funcþie, programele 4, 5, 6 se întrerup cu rufele la

înmuiat (Antiºifonare) iar butonul respectiv semnalizeazã.

- pentru a completa ciclul apãsaþi pe butonul START/RESET sau pe

butonul CALCÃ MAI UªOR.

- pentru a efectua doar descãrcarea poziþionaþi selectorul pe simbolul

respectiv ºi apãsaþi pe butonul START/RESET. .

În acest moment nu puteþi utiliza funcþia ANTIPATÃ.

3, 4, 5, 6,

7, 8, 9,

Clãtiri.

Taste FUNCÞIONARE

Sertarul detergenþilor

Un rezultat bun la spãlare depinde ºi de dozarea

corectã a detergentului: cu un exces de detergent

nu se spalã în mod mai eficace ºi se contribuie la

încrustarea pãrþilor interne ale maºinii de spãlat ºi

poluarea mediului înconjurãtor.

Extrageþi sertarul pentru

detergenþi ºi introduceþi

detergentul sau aditivul

dupã cum urmeazã:

sertarul 1: Detergent pentru prespãlare

(sub formã de praf)

Înainte de a vãrsa detergentul verificaþi ca sertarul

adiþional 4 sã nu fie introdus.

sertarul 2: Detergent pentru spãlare

(sub formã de praf sau lichid)

Detergentul lichid trebuie vãrsat doar înainte de pornire.

sertarul 3: Aditivi (soluþie de înmuiat, etc.)

Soluþia de înmuiat nu trebuie sã iasã deasupra grãtarului.

sertar adiþional 4: Decolorant

 Nu folosiþi detergenþi pentru spãlare manualã,

deoarece formeazã prea multã spumã.

Ciclu de albire

 Decolorantul tradiþional se foloseºte pentru

þesãturi rezistente albe, cel delicat pentru þesãturi

colorate, sintetice ºi pentru lânã.

Introduceþi sertarul

adiþional 4, aflat în

dotare, în sertarul 1.

Când dozaþi

decolorantul nu depãºiþi

nivelul max indicat pe

pivotul central (vezi

figura).

Pentru efectuarea doar a decolorãrii, vãrsaþi

decolorantul în sertarul adiþional 4 ºi selectaþi programul

Clãtire

Pentru albirea în timpul spãlãrii, vãrsaþi detergentul

ºi aditivii, selectaþi programul dorit ºi activaþi

opþiunea Antipatã (vezi pag. 19).

Folosirea sertarului adiþional 4 exclude

prespãlarea.

Prepararea rufelor

 Subdivizaþi rufele în funcþie de:

- tipul de þesãturã / simbolul de pe etichetã.

- culori: separaþi rufele colorate de cele albe.

 Goliþi buzunarele ºi controlaþi nasturii.

 Nu depãºiþi valorile indicate, referitoare la

greutatea rufelor uscate:

Þesãturi rezistente: max 5 kg

Þesãturi sintetice: max 2,5 kg

Þesãturi delicate: max 2 kg

Lânã: max 1 kg

Cât cântãresc rufele?

1 cearceaf: 400-500 g.

1 faþã de pernã: 150-200 g.

1 faþã de masã: 400-500 g.

1 halat de baie: 900-1.200 g.

1 prosop: 150-250 g.

Rufe deosebite

Perdele: împãturiþi-le ºi aºezaþi-le într-o faþã de

pernã sau într-un sac de tip plasã Spãlaþi-le singure

fãrã a depãºi o jumãtate din încãrcãturã. Folosiþi

programul 6 care exclude centrifugarea.

Plãpumi ºi haine de vânt: dacã cãptuºeala este din

fulgi de gâscã sau de raþã se pot spãla în maºina de

spãlat. Întoarceþi lucrurile pe dos ºi formaþi o

încãrcãturã maximã de 2-3 kg, repetând clãtirea o

datã sau de douã ori ºi utilizând centrifuga

delicatã.

Lânã: pentru a obþine cele mai bune rezultate,

folosiþi un detergent specific ºi nu depãºiþi 1 kg de

rufe.

Detergenþi ºi rufe albe

Pagina se încarcă ...

Indesit WIE 107 XS (EX) Manualul utilizatorului

Marca: Indesit

Model: WIE 107 XS (EX)

Categorie: Mașini de spălat

Tip: Manualul utilizatorului

Descărcați PDF

raport

în alte limbi

English: Indesit WIE 107 XS (EX) User guide
slovenčina: Indesit WIE 107 XS (EX) Užívateľská príručka

Indesit WIE 107 XS (EX) Manualul utilizatorului

Indesit WIE 107 XS (EX) Manualul utilizatorului

în alte limbi

Lucrări conexe

Alte documente