Indesit WIE 107 XS (EX) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului
1
GB
English,1
Contents
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
Display, 5
MEMO Programme, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
Setting the spin cycle, 7
Setting the Delay Timer, 7
Setting the temperature, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Bleach cycle, 8
Preparing your laundry, 8
Special items, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Cleaning the detergent dispenser, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
WASHING MACHINE
WIE 107 XS
Instructions for use
GB
Magyar,2 5
HU
Românã,13
RO
Èeský,37
CZ
2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the 4
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Use the plug provided to seal the three holes
where the plug was housed, situated on the lower
right-hand side on the rear of your appliance.
6. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mouth (see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Installation
A
3
GB
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
65 - 100 cm
Technical details
Model
WIE 107 XS
Dimensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity
from 1 to 5 kg
Electric
connections
voltage 220/230 Volts 50 Hz
maximum absorbed power 1850 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
Spin speed
up to 1000 rpm
Control
programmes
according to
IEC456 directive
programme 2; temperature 60°C;
run with a load of 5 kg.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
4
GB
Control panel
Washing machine description
Control knob
Display
Detergent dispenser
SPIN
button
TEMPERATURE
button
START/STOP
button
START/RESET
button
Detergent dispenser to add detergent and fabric
softener (see page 8).
SPIN button to adjust the spin speed or exclude it
altogether (see page 7).
DELAY TIMER button to delay the start of the set
programme for a maximum period of 24 hours
(see page 7).
TEMPERATURE button to adjust the wash tempe-
rature (see page 7).
Display to programme the washing machine and
follow the wash cycle progress (see opposite page).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
START/RESET button to start the programmes or
cancel any incorrect settings.
START/STOP button to turn the washing machine
on and off.
Control knob to select the wash programmes.
The knob stays still during the cycle.
DELAY TIMER
button
FUNCTION
Buttons
5
GB
Display
In addition to being a practical tool to programme your appliance (see page 7), the display provides useful
information concerning the wash cycle.
Once you have pressed the START/RESET button to
start the programme, the display will indicate the
amount of time left until the end of the wash cycle. If
a delayed start has been set (using the Delay Timer,
see page 7), the delay time will be indicated on the
display.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Door lock:
If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid
any damages, wait for the symbol to switch itself off before you open the appliance door.
At the end of the programme, the word END is displayed.
In the event of an anomaly, an error code will appear, such as: F-01, which should be communicated to the
Service Centre (see page 12).
"MEMO" Programme
This programme allows you to store your favourite or most-used wash cycle.
All you have to do is set the desired programme and, once it has started, turn the KNOB to position
; the
wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.
Subsequently, you can start the "MEMO" cycle by simply turning the KNOB to position
; you will be able to
see the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to
modify them but this variation will only be valid for the programme in progress and it will not be stored in the
"MEMO" cycle.
If you want to store a new wash cycle, repeat the above-mentioned operations.
6
GB
Type of fabric and
degree of soil
Programmes
Te m p e -
rature
Detergent
Fabric
softener
Stain removal
option/bleach
Cycle
length
(m inute s)
Description of wash cycle
pre-
wash
wash
Standard
Extremely soiled whites
(sheets, tablecloths, etc.)
1
90°C
135
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Extremely soiled whites
(sheets, tablecloths, etc.)
2
90°C
Delicate/
Traditional
125
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast
colours
2
60°C
Delicate/
Traditional
110
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and
delicate colours
2
40°C
Delicate/
Traditional
105
Wash cycle, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and
delicate colours (shirts,
jumpers, etc.)
3
40°C
Delicate/
Traditional
70
Wash cycle, rinse cycles,
intermediate and final spin cycles
Heavily soiled fast colours
(baby linen, etc.)
4
60
°C
Delicate
75
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Heavily soiled fast colours
(baby linen, etc.)
4
40°C Delicate
60
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Wool
5
40°C
50
Wash cycle, rinse cycles
,
anti-
crease and delicate spin cycle
Very delicate fabrics
(curtains, silk, viscose, etc.)
6
30°C
45
Wash cycle, rinse cycles, anti-
crease or draining cycle
Time 4 you
Heavily soiled whites and fast
colours
7
60°C
65
Wash cycle, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and
delicate colours (shirts,
jumpers, etc.)
8
40°C
55
Wash cycle, rinse cycles,
intermediate and final spin cycles
Delicate colours (all types of
slightly soiled garments)
9
40
°C

45
Wash cycle, rinse cycles,
delicate spin cycle
Delicate colours (all types of
slightly soiled garments)
10
30°C 30
Wash cycle, rinse cycles and
delicate spin cycle
Sport
Sports shoes
(MAX. 2 pairs)
11
30
°C
 50
Cold wash (without detergents),
wash cycle, rinse cycles, and
delicate spin cycle
Fabrics for sportswear
(Tracksuits, shorts, etc.)
12
30°C 60
Wash cycle, rinse cycles,
intermediate and final spin cycles
MEMO
Allows for any wash cycle to be stored
PARTIAL PROGRAMMES
Rinse
Delicate/
Traditional
Rinse cycles and spin cycle
Spin Draining and spin cycle
Drain Draining
Starting and Programmes
Programme table
Notes
-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.
-For programme 12 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (10 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Briefly: starting a programme
1. Turn the washing machine on by pressing button .
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the knob to the desired programme. The
estimated duration of the selected programme is
displayed. The temperature and spin speed are
automatically set according to the programme
(to change them, see page 7).
4. Select any functions (see page 7).
5. Add the detergent and any fabric softener
(see page 8).
6. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
7. When the programme has ended, the word END is
displayed. Take out your laundry and leave the
appliance door ajar to allow the drum to dry
thoroughly.
8. Turn the washing machine off by pressing button
.
(see page 5).
7
GB
Function Effect Comments
Enabled with
programmes:
Stain
removal
Bleaching cycle
designed to
remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(se
e page 8)
.
This function is incompatible with the EASY IRON function.
2, 3, 4,
Rinse cycle.
Extra Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 7,
8, 9, 11, 12,
Rinse cycle.
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4, 5, 6 will end, with the
laundry left to soak (Anti-crease), and the relative button flashes:
- to conclude the cycle, press the START/RESET button or the
EASY IRON button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
This function is incompatible with the STAIN REMOVAL function.
3, 4, 5, 6, 7, 8,
9, Rinse
cycle.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Personalisations
Setting the temperature
If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature
needs to be regulated, a fixed
appears. Press button and the maximum temperature allowed for the
programme set will be displayed and the
icon flashes. Press it again and the temperature lowers until it
reaches OFF, which indicates a cold wash cycle (press it again to go back to the maximum value); stop on the
desired value, after approximately 2 seconds the setting is accepted: the symbol
remains fixed.
The temperature adjustment is enabled with all wash programmes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
If you set a function that is incompatible with another function you selected previously, only the last one
selected will be enabled.
Setting the spin cycle
If, when the appliance is switched on, the KNOB is positioned
on a programme with a spin cycle, a fixed
appears. Press
button
and the maximum spin speed allowed for the
programme set will be displayed, and the
icon flashes. Press
it again and the values lower until they reach OFF, which
indicates that the spin cycle has been excluded (press it again
to go back to the maximum value); stop on the desired speed,
after approximately 2 seconds the setting is accepted: the
symbol
remains fixed.
The spin cycle setting is enabled with all the programmes
except for 6 and the Draining cycle.
Setting the Delay Timer
Press the button and you will see the word OFF on the
display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one
hour (this can reach up to 24h); stop on the "desired" delay;
after approximately 2 seconds the setting is accepted, following
which, the time for the set programme appears on the display
and the symbol
remains on.
If you now press the START/RESET button, the set "delay"
appears; this decreases every hour until the start of the cycle.
In this phase, the "delay" can only be modified by decreasing it.
The Delay Timer regulation is enabled with all programmes.
FUNCTION buttons
8
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
Before pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into extra
compartment 4 and set the Rinse programme
.
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal function (see page 7).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
Empty all pockets and check for loose buttons.
Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Detergents and laundry
1
2
3
4
9
GB
Precautions and advice
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not open the detergent dispenser while the
appliance is in operation.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
The appliance door tends to get quite hot during
the wash cycle.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
Disposing of an old washing machine:
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best
results: an objective reached to respect the
environment.
Saving on detergent, water,
energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity
supply
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
drum
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
can't easily be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won't
start.
The wash cycle won't start.
The washing machine fails to
load water (The wording H2O is
displayed).
The washing machine
continuously loads and unloads
water.
The washing machine does not
drain or spin.
The washing machine vibrates
too much during the spin cycle.
The washing machine leaks.
There is too much foam.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance door is not shut properly (the word DOOR is
displayed).
The
button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
A delayed start has been set (using the Delay Timer, see page 7).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
washing machine to load and unload water continuously. In order to avoid
such an inconvenience, special anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The washing machine is not level (see page 2).
The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
You used too much detergent.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
Service
Service
13
RO
Românã
Sumar
Instalare, 14-15
Scoaterea din ambalaj ºi nivelarea, 14
Legãturi hidraulice ºi electrice, 14-15
Primul ciclu de spãlare, 15
Date tehnice, 15
Descrierea maºinii de spãlat, 16-17
Panoul de control, 16
Display-ul, 17
Program MEMO, 17
Pornire ºi Programe, 18
Pe scurt: pornirea unui program, 18
Tabel de programe, 18
Personalizãri, 19
Reglarea centrifugei, 19
Reglarea delay timerului, 19
Reglarea temperaturii, 19
Funcþii, 19
Detergenþi ºi rufe albe, 20
Sertarul detergenþilor, 20
Ciclu de albire, 20
Prepararea rufelor, 20
Rufe deosebite, 20
Precauþii ºi sfaturi, 21
Protecþie generalã, 21
Aruncarea reziduurilor, 21
Protecþia ºi respectarea mediului înconjurãtor, 21
Întreþinere ºi îngrijire, 22
Oprirea apei ºi a curentului electric, 22
Curãþarea maºinii de spãlat, 22
Curãþarea sertarului pentru detergenþi, 22
Îngrijirea hubloului ºi a coºului, 22
Curãþarea pompei, 22
Controlarea tubului de alimentare cu apã, 22
Anomalii ºi remedii, 23
Asistenþã, 24
Înainte de a lua legãtura cu Asistenþa, 24
RO
MAªINÃ DE SPÃLAT RUFE
WIE 107 XS
INSTRUCÞIUNI DE FOLOSIRE
14
RO
Este important se pãstreze acest manual
pentru a-l putea consulta în orice moment. În caz
de vânzare, de cesiune sau de schimbare a
locuinþei, acesta trebuie rãmânã împreunã cu
maºina de spãlat pentru a informa noul proprietar
cu privire la funcþionare ºi la respectivele
avertismente.
Citiþi cu atenþie instrucþiunile: veþi gãsi informaþii
importante cu privire la instalare, la folosire ºi la
siguranþã.
Scoaterea din ambalaj ºi nivelarea
Scoaterea din ambalaj
1. Scoaterea din ambalaj a maºinii de spãlat.
2. Controlaþi ca maºina de spãlat sã nu fi fost
deterioratã în timpul transportului. Dacã este deterioratã
nu o conectaþi ºi luaþi legãtura cu cine v-a vândut-o.
3. Scoateþi cele 4
ºuruburi de protecþie
pentru transport ºi
cauciucul cu respectivul
distanþator, situate în
partea posterioarã (vezi
figura).
4. Închideþi orificiile cu dopurile din plastic aflat în dotare.
5. Închideþi cu dopul aflat în dotare cele trei orificii în care
se afla fiºa, situate în partea posterioarã, jos în dreapta.
6. Pãstraþi toate piesele: pentru cazul în care maºina de
spãlat va trebui sã fie transportatã, piesele vor trebui
montante din nou.
Ambalajele nu constituie jucãrii pentru copii
Nivelare
1. Instalaþi maºina de spãlat pe un paviment plan ºi
rigid, fãrã a o sprijini de ziduri, mobilã sau altceva.
2. Dacã podeaua nu este
perfect orizontalã,
compensaþi neregularitãþile
deºurubând sau
înºurubând picioruºele
anterioare (vezi figura);
unghiul de înclinare,
mãsurat pe planul de
lucru, nu trebuie
depãºeascã 2°.
O nivelare precisã conferã stabilitate maºinii ºi
evitã vibraþii, zgomote ºi deplasãri pe timpul
funcþionãrii. În cazul mochetelor sau a unui covor,
reglaþi picioruºele astfel încât menþineþi sub
maºina de spãlat un spaþiu suficient pentru
ventilare.
Legãturi hidraulice ºi electrice
Conectarea tubului de alimentare cu apã
1. Introduceþi garnitura
A în extremitatea
tubului de alimentare ºi
înºurubaþi-l la un robinet
de apã rece cu gura
filetatã de ¾ gaz (vezi
figura).
Înainte de conectare,
lãsaþi apa curgã
pentru a se limpezi.
2. Conectaþi tubul de
alimentare la maºina
de spãlat,
înºurubându-l la
respectiva prizã de
apã, în partea
posterioarã, sus în
dreapta (vezi figura).
3. Fiþi atenþi ca tubul nu fie nici curbat nici
îndoit.
Presiunea apei trebuie fie cuprinsã în valorile
tabelului Date tehnice (vezi pagina alãturatã).
Dacã lungimea tubului de alimentare nu este
suficientã, adresaþi-vã unui magazin specializat sau
unui tehnician autorizat.
Instalare
A
15
RO
Conectarea tubului de evacuare
Conectaþi tubul de
evacuare, fãrã a-l îndoi,
la o conductã de
evacuare sau la o gurã
de evacuare în zid,
situate între 65 ºi 100
cm de pãmânt;
sau sprijiniþi-l pe
marginea unei chiuvete
sau a unei cãzi, legând
ghidul aflat în dotare,
de robinet (vezi figura).
Extremitatea liberã a
tubului de evacuare nu
trebuie rãmânã
cufundatã în apã.
Nu este recomandabilã folosirea tuburilor de
prelungire; dacã este indispensabil, tubul de
prelungire trebuie aibã acelaºi diametru cu tubul
original ºi nu trebuie depãºeascã 150 cm.
Legãtura electricã
Înainte de a introduce fiºa în priza de curent,
asiguraþi-vã ca:
priza fie cu împãmântare ºi conform
prevederilor de lege;
priza poatã suporta sarcina maximã de
putere a maºinii, indicatã în tabelul cu Date
tehnice (vezi alãturi);
tensiunea de alimentare sã fie cuprinsã în valorile
indicate în tabelul cu Date tehnice (vezi alãturi);
priza sã fie compatibilã cu fiºa maºinii de spãlat.
În caz contrar înlocuiþi priza sau fiºa.
Maºina de spãlat nu trebuie instalatã afarã, nici chiar
în cazul în care spaþiul este adãpostit, deoarece este
foarte periculoasã expunerea maºinii la ploi ºi furtuni.
Dupã instalarea maºinii de spãlat, priza de curent
trebuie sã fie uºor accesibilã.
Nu folosiþi prelungitoare ºi prize multiple.
Cablul nu trebuie fie îndoit sau comprimat.
Cablul de alimentare trebuie fie înlocuit doar
de tehnicieni autorizaþi.
Atenþie! Producãtorul îºi declinã orice
responsabilitate pentru cazul în care aceste norme
nu se respectã.
Primul ciclu de spãlare
Dupã instalare, înainte de folosire, efectuaþi un ciclu
de spãlare cu detergent ºi fãrã rufe, selectând
programul la 90°C fãrã prespãlare.
AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere
65 - 100 cm
Date tehnice
Model
WIE 107 XS
Dimensiuni
lãrgime 59,5 cm
înãlþime 85 cm
profunzime 53,5 cm
Capacitate
de la 1 la 5 kg
Legãturi electrice
tensiune 220/230 Volþi 50 Hz
putere maximã absorbitã 1850 W
Legãturi hidrice
presiune maximã 1 MPa (10 bari)
presiune minimã 0,05 MPa (0,5 bari)
capacitatea cuvei 46 litri
Viteza de centrifugare
pânã la 1000 de rotaþii pe minut
Programe de control
pe baza normei
IEC456
programul 2; temperatura 60
°
C;
efectuatã cu 5 kg de rufe.
Acest aparat este conform cu
urmãtoarele Directive Comunitare:
- 73/23/CEE din data de 19/02/73
(Tensiuni Joase) ºi modificãri succesive
- 89/336/CEE din data de 03/05/89
(Compatibilitate Electromagneticã) ºi
modificãri succesive
16
RO
Panoul de control
Descrierea maºinii de spãlat
Selectorul
Display-ul
Sertarul detergenþilor
Butonul
CENTRIFUGÃ
Butonul
TEMPERATURÃ
Butonul
PORNIRE/OPRIRE
Butonul
START/RESET
Sertarul detergenþilor pentru a încãrca detergenþi
ºi aditivi (vezi pag. 20).
Butonul CENTRIFUGÃ pentru reglarea vitezei de
centrifugare pânã la excluderea acesteia
(vezi pag. 19).
Buton DELAY TIMER pentru a întârzia pornirea
programului selectat cu maxim 24 de ore
(vezi pag. 19).
Butonul TEMPERATURÃ pentru modificarea
temperaturii de spãlare (vezi pag. 19).
Display-ul pentru programarea maºinii de spãlat ºi
efectuarea avansãrii ciclurilor de spãlare (vezi
pagina alãturatã).
Taste FUNCÞIONARE: pentru a selecta funcþiile
disponibile. Butonul corespunzãtor funcþiei
selectate va rãmâne aprins.
Butonul START/RESET pentru pornirea
programelor sau anularea a ceea a fost selectat
greºit.
Butonul PORNIRE/OPRIRE pentru pornirea ºi
stingerea maºinii de spãlat.
Selectorul pentru alegerea programelor.
Pe durata programului selectorul rãmâne ferm.
Butonul
DELAY TIMER
Taste
FUNCÞIONARE
17
RO
AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere
Display-ul
În afarã de faptul este un instrument util pentru programarea maºinii (vezi pag. 19), displayul furnizeazã
informaþii cu privire la ciclul de spãlare.
Dupã apãsarea butonului START/RESET pentru a
porni programul, pe display este cronometratã
durata rezidualã pânã la iniþierea programului de
spãlare ales. În cazul în care iniþierea programului de
spãlare dupã un anumit interval de timp (Delay
Timer, vezi pag. 19), aceasta va fi vizualizatã.
Hublou blocat:
Simbolul aprins indicã faptul hubloul este blocat pentru a împiedica deschideri întâmplãtoare.
Pentru a evita daunele ce pot deriva dintr-o funcþionare defectuoasã, este necesar aºteptaþi ca simbolul
se stingã înainte de a deschide hubloul.
La sfârºitul programului se vizualizeazã cuvântul END.
În caz de anomalie apare un cod de eroare, de exemplu: F-01, de transmis Asistenþei Tehnice (vezi pag. 24).
Program MEMO
Acest program permite memorizarea ciclului de spãlare preferat sau cel mai utilizat.
Este suficient se selecteze programul dorit ºi dupã pornire se roteascã SELECTORUL pe poziþia
,
automat ciclul va fi memorizat iar pe display va apãrea scris MEMO intermitent timp de câteva secunde.
Dupã aceea va fi posibilã pornirea unui ciclu MEMO doar prin rotirea SELECTORULUI la poziþia
; se vor
putea vizualiza valorile de temperaturã/centrifugã/delay timer apãsând pe butoanele corespunzãtoare, se vor
putea chiar ºi modifica însã aceastã variaþie va fi valabilã doar pentru programul în curs ºi nu va fi memoratã în
ciclul MEMO.
Dacã se doreºte memorarea unui nou ciclu de spãlare, repetaþi operaþiunile indicate mai sus.
18
RO
Tipul de þesãturã ºi de murdãrie Programe
Tempe-
raturã
Detergent
A ditiv
înm uiere
Opþiune
Antipatã /
Decolorant
Durata
ciclului
(minute)
Descrierea ciclului de spãlare
presp. Spãl.
Standard
Albe extrem de murdare
(cearceafuri, feþe de masã, etc.)
1
90°C

135
Prespãlare, spãlare, clãtiri,
centrifugi intermediare ºi finale
Albe extrem de murdare
(cearceafuri, feþe de masã, etc.)
2
90°C

Delicatã /
Tradiþionale
125
Spãlare, ctiri, centrifugi
intermediare ºi finale
Albe ºi colorate rezistente foarte
murdare
2
60°C

Delicatã /
Tradiþionale
110
Spãlare, ctiri, centrifugi
intermediare ºi finale
Albe ºi colorate delicate foarte
murdare
2
40°C

Delicatã /
Tradiþionale
105
Spãlare, ctiri, centrifugi
intermediare ºi finale
Albe pin murdare ºi culori
delicate (cãmãºi, bluze, etc.)
3
40°C

Delicatã /
Tradiþionale
70
Spãlare, ctiri, centrifugi
intermediare ºi finale
Culori rezistente foarte murdare
(scutece pentru noi nãscuþi, etc.)
4
60
°C
Delicatã
75
Spãlare, ctiri, antiºifonare sau
centrifugare delicatã
Culori rezistente foarte murdare
(scutece pentru noi nãscuþi, etc.)
4
40°C
Delicatã
60
Spãlare, ctiri, antiºifonare sau
centrifugare delicatã
5
40°C

50
Spãlare, clãtiri
,
antiºifonare ºi
centrifugare delicatã
Þeturi foarte delicate
(perdele, mãtase, vâscozã, etc.)
6
30°C

45
Spãlare, ctiri, antiºifonare sau
scurgere
Timp pentru tine
Albe ºi colorate rezistente foarte
murdare
7
60°C

65
Spãlare, ctiri, centrifugi
intermediare ºi finale
Albe pin murdare ºi culori
delicate (cãmãºi, bluze, etc.)
8
40°C

55
Spãlare, ctiri, centrifugi
intermediare ºi finale
Culori delicate (rufe de toate
tipurile puþin murdare)
9
40
°C

45
Spãlare, ctiri ºi centrifugare
delicatã
Culori delicate (rufe de toate
tipurile puþin murdare)
10
30°C
 30
Spãlare, ctiri ºi centrifugare
delicatã
Sport
Încãlþãminte sportivã
(
MAX 2 perechi.
)
11
30
°C
 50
Spãlare la rece (fãrã detergent),
spãlare, ctiri ºi centrifugã delicatã
Þesãturi pentru îmbrãcãminte sportivã
(Treninguri, chiloþi de gimnasticã, etc.
12
30°C
 60
Spãlare, ctiri, centrifugi
intermediare ºi finale
MEMO
Permite memorarea oricãrui tip de spãlare
PROGRAME PARÞIALE
Ctire
Delicatã /
Tradiþionale
Ctiri ºi centrifugare
Centrifugare Descãrcare apã ºi centrifugare
Descãrcare Descãrcare
Pornire ºi Programe
Tabel de programe
Pe scurt: pornirea unui program
1. Porniþi maºina de spãlat apãsând butonul .
2. Introduceþi rufele ºi închideþi hubloul.
3. Selectaþi cu ajutorul selectorului programul dorit.
Pe display va apãrea timpul estimat.
Temperatura ºi centrifuga se selecteazã automat
pe baza programului (pentru a le modifica vezi
pag. 19).
4. Selectaþi eventuale funcþii (vezi pag. 19).
5. Vãrsaþi detergenþi ºi aditivi (vezi pag. 20).
6. Porniþi programul apãsând butonul START/
RESET.
Pentru a anula þineþi apãsat butonul START/
RESET timp de cel puþin 2 secunde.
7. La sfârºitul programului va apãrea scris END.
Scoateþi rufele ºi lãsaþi hubloul întredeschis
pentru a se putea usca coºul.
8. Închideþi maºina de spãlat apãsând butonul
.
Note
-Pentru programele 7 - 8 este recomandabil nu se depãºeascã o cantitate de rufe de 3,5 kg.
-Pentru programul 12 este recomandabil nu se depãºeascã o cantitate de rufe de 2 kg.
-Antiºifonare-vezi calcã mai uºor, pagina alãturatã. Datele specificate în tabel au valoare indicativã.
Program special
Zilnic 30 (programul 10 pentru materiale sintetice) este studiat pentru a spãla rufe puþin murdare într-un
interval scurt de timp: dureazã doar 30 de minute economisindu-se energie ºi timp. Selectând programul
(10 la 30°C) este posibilã spãlarea împreunã a þesãturilor de diverse tipuri (excluse lâna ºi mãtasea) cu o
încãrcãturã maximã de 3 kg. Se recomandã folosirea detergentului lichid.
(vezi pag. 17).
19
RO
Personalizãri
AsistenþãAnomaliiPrecauþii ÎntreþinerePrograme DetergenþiInstalare Descriere
Reglarea centrifugei
Dacã la pornirea maºinii, SELECTORUL este poziþionat pe un
program care prevede centrifuga, icoana
apare fixã. Apãsând
pe butonul
se vizualizeazã viteza maximã permisã a
centrifugii pentru programul selectat iar icoana
semnalizeazã. Apãsând din nou valorile coboarã pânã la OFF,
ceea ce indicã excluderea centrifugii (apãsaþi din nou pentru a
reveni la valoarea cea mai mare); opriþi-vã la valoarea doritã,
dupã circa 2 secunde selecþia se acceptã: simbolul
rãmâne
fix. Reglarea centrifugei este activã pentru toate programele cu
excepþia programului 6 ºi a evacuãrii.
Reglarea delay timerului
Apãsând pe butonul pe display se vizualizeazã scris OFF
iar simbolul respectiv se ilumineazã intermitent.
Apãsând din nou pe buton apare 1h adicã întârziere de o orã
ºi aºa mai departe pânã la 24h; opriþi-vã la întârzierea doritã,
dupã circa 2 secunde selecþia se acceptã; dupã aceea pe
display se vizualizeazã timpul prevãzut pentru programul
selectat iar simbolul
rãmâne aprins.
Apãsând pe butonul START/RESET apare din nou valoarea
întârzierii selectate care scade la fiecare orã pânã la pornirea ciclului; în aceastã fazã se poate modifica
valoarea întârzierii doar micºorând-o. Reglarea Delay Timerului este activã cu toate programele.
Reglarea temperaturii
Dacã la pornirea maºinii, SELECTORUL este poziþionat pe un program care prevede reglarea temperaturii,
icoana
apare fixã. Apãsând pe butonul se vizualizeazã temperatura maximã permisã pentru programul
selectat iar icoana
semnalizeazã. Apãsând din nou, temperatura coboarã pânã la OFF, care indicã spãlarea
la rece (apãsaþi din nou pentru a reveni la valoarea cea mai mare); opriþi-vã la valoarea doritã, dupã circa 2
secunde selecþia se acceptã: simbolul
rãmâne fix.
Reglarea temperaturii este activã cu toate programele de spãlare.
Funcþii
Diferitele funcþii de spãlare prevãzute pentru maºina de spãlat permit obþinerea unor rezultate excepþionale (o
calitate îmbunãtãþitã a spãlãrii-rufe curate, etc.). Pentru a activa aceste funcþii, procedaþi astfel:
1. apãsaþi butonul aferent funcþiei dorite, þinând cont de informaþiile conþinute în tabelul de mai jos;
2. aprinderea butonului respectiv indicã faptul funcþia respectivã a fost activatã.
Notã: Intermitenþa rapidã a butonului indicã faptul funcþia respectivã nu este selecþionabilã pentru programul ales.
În cazul în care va fi selectatã o funcþie incompatibilã cu cea selectatã mai înainte, doar ultima aleasã va rãmâne activã.
Funcþii Efect Note pentru folosire
Activã cu
programele:
Antipa
Ciclu de decolorare
adecvat pentru
eliminarea petelor
mai rezistente.
A se vãrsa decolorantul în sertarul adiþional 4
(a se vedea pag. 20
)
În acest moment nu puteþi utiliza funcþia CAL MAI UªOR.
2, 3, 4,
Clãtiri.
Extra
Clãtire
reºte eficacitatea
clãtirii.
Se recomandã cu maºina plisau cu doze elevate de detergent.
1, 2, 3, 4,
7, 8, 9, 11,
12, Clãtiri.
Calcã mai
uºor
Reduce pliurile la
þeturi facilitând
cãlcarea.
Selectând aceastã funcþie, programele 4, 5, 6 se întrerup cu rufele la
înmuiat (Antiºifonare) iar butonul respectiv semnalizeazã.
- pentru a completa ciclul apãsaþi pe butonul START/RESET sau pe
butonul CALCÃ MAI UªOR.
- pentru a efectua doar descãrcarea poziþionaþi selectorul pe simbolul
respectiv ºi asaþi pe butonul START/RESET. .
În acest moment nu puteþi utiliza funcþia ANTIPATÃ.
3, 4, 5, 6,
7, 8, 9,
Clãtiri.
Taste FUNCÞIONARE
20
RO
Sertarul detergenþilor
Un rezultat bun la spãlare depinde ºi de dozarea
corectã a detergentului: cu un exces de detergent
nu se spalã în mod mai eficace ºi se contribuie la
încrustarea pãrþilor interne ale maºinii de spãlat ºi
poluarea mediului înconjurãtor.
Extrageþi sertarul pentru
detergenþi ºi introduceþi
detergentul sau aditivul
dupã cum urmeazã:
sertarul 1: Detergent pentru prespãlare
(sub formã de praf)
Înainte de a vãrsa detergentul verificaþi ca sertarul
adiþional 4 sã nu fie introdus.
sertarul 2: Detergent pentru spãlare
(sub formã de praf sau lichid)
Detergentul lichid trebuie vãrsat doar înainte de pornire.
sertarul 3: Aditivi (soluþie de înmuiat, etc.)
Soluþia de înmuiat nu trebuie sã iasã deasupra grãtarului.
sertar adiþional 4: Decolorant
Nu folosiþi detergenþi pentru spãlare manualã,
deoarece formeazã prea multã spumã.
Ciclu de albire
Decolorantul tradiþional se foloseºte pentru
þesãturi rezistente albe, cel delicat pentru þesãturi
colorate, sintetice ºi pentru lânã.
Introduceþi sertarul
adiþional 4, aflat în
dotare, în sertarul 1.
Când dozaþi
decolorantul nu depãºiþi
nivelul max indicat pe
pivotul central (vezi
figura).
Pentru efectuarea doar a decolorãrii, vãrsaþi
decolorantul în sertarul adiþional 4 ºi selectaþi programul
Clãtire
.
Pentru albirea în timpul spãlãrii, vãrsaþi detergentul
ºi aditivii, selectaþi programul dorit ºi activaþi
opþiunea Antipatã (vezi pag. 19).
Folosirea sertarului adiþional 4 exclude
prespãlarea.
Prepararea rufelor
Subdivizaþi rufele în funcþie de:
- tipul de þesãturã / simbolul de pe etichetã.
- culori: separaþi rufele colorate de cele albe.
Goliþi buzunarele ºi controlaþi nasturii.
Nu depãºiþi valorile indicate, referitoare la
greutatea rufelor uscate:
Þesãturi rezistente: max 5 kg
Þesãturi sintetice: max 2,5 kg
Þesãturi delicate: max 2 kg
Lânã: max 1 kg
Cât cântãresc rufele?
1 cearceaf: 400-500 g.
1 faþã de pernã: 150-200 g.
1 faþã de masã: 400-500 g.
1 halat de baie: 900-1.200 g.
1 prosop: 150-250 g.
Rufe deosebite
Perdele: împãturiþi-le ºi aºezaþi-le într-o faþã de
pernã sau într-un sac de tip plasã Spãlaþi-le singure
fãrã a depãºi o jumãtate din încãrcãturã. Folosiþi
programul 6 care exclude centrifugarea.
Plãpumi ºi haine de vânt: dacã cãptuºeala este din
fulgi de gâscã sau de raþã se pot spãla în maºina de
spãlat. Întoarceþi lucrurile pe dos ºi formaþi o
încãrcãturã maximã de 2-3 kg, repetând clãtirea o
datã sau de douã ori ºi utilizând centrifuga
delicatã.
Lânã: pentru a obþine cele mai bune rezultate,
folosiþi un detergent specific ºi nu depãºiþi 1 kg de
rufe.
Detergenþi ºi rufe albe
1
2
3
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Indesit WIE 107 XS (EX) Manualul utilizatorului

Categorie
Mașini de spălat
Tip
Manualul utilizatorului