Ubiquiti AG-HP-2G2 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: AG-HP-2G2

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

5 GHz High-Performance

Integrated InnerFeed

™

Antenna

Model: AG-HP-5G27

Introduction

Thank you for purchasing the Ubiquiti Networks

™

airGrid® 5GHz

High-Performance Integrated InnerFeed

™

Antenna. This Quick

Start Guide is designed to guide you through the installation, and

show you how to access the airOS® Configuration Interface. This

Quick Start Guide also includes the warranty terms and is for use

with the airGridM5 HP, model AG-HP-5G27.

Package Contents

Antenna Feed Feed Extender Grid Reflector

Rear Housing L-Bracket Pole Clamp M8 U-Bolt

5 GHz High-Performance

Integrated InnerFeed

Antenna

Model: AG-HP-5G27

M8 Flange Nuts

(Qty. 2)

PoE Adapter

(24V, 0.5A)

Power Cord Quick Start Guide

Grid reflector and mounting hardware packaged separately. Products may be different from

pictures and are subject to change without notice.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• 13 mm or ½" wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Application Examples

The airGrid mounted outdoors with the Grid Reflector installed

provides directional outdoor coverage

(gain reflector-dependent).

The airGrid mounted outdoors without the Grid Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light green when the wireless signal

strength is above -65 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light red when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light green when the

device is connected to a power source.

Hardware Installation

Assemble the airGrid according to your chosen polarization.

1. Attach the L-Bracket to the Grid Reflector by sliding the tabs

into the slots.

Vertical Polarization Horizontal Polarization

WARNING: The polarization of the airGrid must

match the polarization of its corresponding device

(horizontal to horizontal, vertical to vertical).

2. On the front of the airGrid, ensure the polarization indicator,

V or H, properly matches your desired polarization.

Vertical Polarization Horizontal Polarization

*720-00015-03*

720-00015-03

3. Attach the Rear Housing:

a. Ensure the four alignment holes on the Grid Reflector

and L-Bracket are lined up.

b. Orient the Rear Housing with the locking tab of the

cable feed door facing up.

c. Insert the alignments pins of the Rear Housing into the

alignment holes, and push until the Rear Housing locks

into place with a click.

Vertical Polarization Horizontal Polarization

4. Insert the Feed Extender into the Rear Housing with the

Release Button facing down. Push until it locks into place

with a click.

Release Button

5. Lift the locking tab of the cable feed door and detach the

door from the Rear Housing.

6. Route an Ethernet cable through the Rear Housing and Feed

Extender. Connect the cable to the Ethernet port on the

back of the Antenna Feed.

7. Attach the Antenna Feed:

a. Rotate the Antenna Feed to match the signal

polarization.

b. Insert the Antenna Feed into the Feed Extender, and

push until it locks into place with a click.

Vertical Polarization Horizontal Polarization

8. Lightly pull the Antenna Feed to ensure that the Release

Button is fully engaged and locked into place.

Antenna Feed

Feed Extender

Release Button

Bottom View

Note: If you need to remove the Antenna Feed, you

must depress the Release Button first.

9. The Release Button indicates the Antenna Feed polarization.

Confirm that the polarization indicator, V or H, on the

Antenna Feed matches the indicator on the Grid Reflector.

WARNING: The polarization indicators must match.

Vertical Polarization Horizontal Polarization

10. Re-attach the cable feed door to the Rear Housing. Ensure

the locking tab securely latches to the Rear Housing.

11. Slide the Pole Clamp onto the L-Bracket.

12. Insert the M8 U-Bolt into the Pole Clamp and L-Bracket.

Secure each end of the M8 U-Bolt with a M8 Flange Nut.

9 N-m

(80 lb-in)

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

Connecting Power over Ethernet

1. Connect the other end of the Ethernet cable from the

airGrid to the Ethernet port labeled POE on the PoE

Adapter.

2. Connect an Ethernet cable from your LAN to the Ethernet

port labeled LAN on the PoE Adapter.

3. Connect the Power Cord to the power port on the PoE

Adapter. Connect the other end of the Power Cord to a

power outlet.

airOS Configuration

Verify connectivity in the airOS Configuration Interface and

select the airGrid antenna size.

1. Make sure that your host machine is connected via

Ethernet to the airGrid.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20

in the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: U.S. product versions are locked to the

U.S. Country Code to ensure compliance with

FCC regulations.

5. Select the airGrid antenna size:

a. Click the Wireless tab.

b. From the Antenna drop-down list, select the

appropriate option.

c. Click Change to save.

d. Click OK to confirm.

Customize additional settings as needed to complete

the installation. Please review the Installer Compliance

Responsibility section on the following page.

For additional details on the airOS Configuration Interface,

refer to the User Guide available at

documentation.ubnt.com/airmax

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a

variety of antennas and cables, the Antenna and Output Power

fields are provided to the professional installer to assist in

meeting regulatory requirements.

Specifications

AG-HP-5G27

Dimensions 620 x 460 x 360 mm (Mount Included)

Weight 2585 g (Mount Included)

Networking Interface (1) 10/100 Ethernet Port

Enclosure Outdoor UV Stabilized Plastic

Frequency Worldwide: 5170 - 5875 MHz

USA: 5725 - 5850 MHz

Gain 27 dBi

Output Power 25 dBm

Max. Power Consumption 3.0 W

Power Supply 24V, 0.5A PoE Adapter (Included)

Power Method Passive Power over Ethernet

(Pairs 4, 5+; 7, 8 Return)

Max. VSWR 1.5:1

Wind Survivability 125 mph

Wind Loading 7.8 lbf @ 125 mph

ETSI Specication EN 302 326 DN2

Shock and Vibration ETSI300-019-1.4

Certications FCC, IC, CE

Operating Temperature -30 to 75° C

Operating Humidity 5 to 95% Condensing

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be

located or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d’au moins

20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre

antenne ou transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product and it

must follow the CE marking.

Pagina se încarcă ...

Ubiquiti AG-HP-2G2 Ghid de inițiere rapidă

Marca: Ubiquiti

Model: AG-HP-2G2

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti AG-HP-2G2 Quick start guide
italiano: Ubiquiti AG-HP-2G2 Guida Rapida

Ubiquiti AG-HP-2G2 Ghid de inițiere rapidă

Acest manual este potrivit și pentru

Ubiquiti AG-HP-2G2 Ghid de inițiere rapidă

în alte limbi

Lucrări conexe