Husqvarna 110iL Cordless 36v Grass Trimmer Manual de utilizare

110iL

EN Operator's manual 5-20

SV Bruksanvisning 21-35

DA Brugsanvisning 36-50

NO Bruksanvisning 51-65

FI Käyttöohje 66-79

DE Bedienungsanweisung 80-96

FR Manuel d'utilisation 97-112

NL Gebruiksaanwijzing 113-128

IT Manuale dell'operatore 129-144

ES Manual de usuario 145-160

PT Manual do utilizador 161-176

ET Kasutusjuhend 177-191

LT Operatoriaus vadovas 192-206

LV Lietošanas pamācība 207-221

CS Návod k použití 222-236

SK Návod na obsluhu 237-251

PL Instrukcja obsługi 252-267

HU Használati utasítás 268-283

HR Priručnik za korištenje 284-298

SL Navodila za uporabo 299-313

RO Instrucţiuni de utilizare 314-329

SR Priručnik za rukovaoca 330-344

BG Ръководство за експлоатация 345-362

EL Οδηγίες χρήσης 363-379

JA 取扱説明書 380-394

RU Руководство по эксплуатации 395-412

TR Kullanım kılavuzu 413-427

UK Посібник користувача 428-444

7

8

6

5

9

12

11

10

14

13

1

16

17

15

19

18

4

3

2

20

1

21

22

11

1

2 3 4 5 6 7

8 9 10 11 12 13

14 15

16

17 18 19

20 21

B

A

22

A

B

23 24 25

26 27 28

29 30 31

AB

32

C

33

D

C

34

35 36 37

38 39 40

1

2

3

41 42 43

44 45 46

47 48 49

50 51

Contents

Introduction..................................................................... 5

Safety..............................................................................6

Assembly...................................................................... 12

Operation...................................................................... 12

Maintenance................................................................. 14

Troubleshooting............................................................ 15

Transportation, storage and disposal........................... 16

Technical data.............................................................. 17

Accessories.................................................................. 18

Declaration of Conformity............................................. 19

Introduction

Product description

Husqvarna 110iL is a battery lawn trimmer/lawn edge

trimmer with an electrical motor.

Work is constantly in progress to increase your safety

and efficiency during operation. Speak to your servicing

dealer for more information.

Intended use

The product is used with a trimmer head to cut grass.

Do not use the product for other tasks than grass

trimming, grass clearing and lawn edging.

Note: National regulations can set limit to the

operation of the product.

Product overview

(Fig. 1)

1. Trimmer head

2. Cutting attachment guard

3. Shaft

4. Shaft coupling

5. Loop handle

6. Keypad

7. Power trigger lockout

8. Power trigger

9. Operator's manual

10. Power cord

11. Power on and warning indicator

12. Battery Charger QC80

13. Start/stop button

14. Battery

15. Battery release buttons

16. Battery indicator button

17. Battery status

18. Warning indicator

19. Combination tool

20. Plant guard

21. Connector

22. Battery Charger 40-C80

Symbols on the product

(Fig. 2) WARNING: This product can be

dangerous and cause serious injury or

death to the operator or others. Be careful

and use the product correctly.

(Fig. 3) Read the operator's manual carefully and

make sure that you understand the

instructions before use.

(Fig. 4) Use eye protection.

(Fig. 5) Do not expose to rain.

(Fig. 6) Noise emissions to the environment label

as per EU (also including New South

Wales Legislation) and UK directives and

regulations. Noise emission data can be

found on the machine label and in the

Technical data chapter.

(Fig. 7) Keep bystanders away from the product.

(Fig. 8) Disconnect battery before maintenance.

(Fig. 9) The product or package of the product is

not domestic waste. Recycle it at a

recycling station for electrical and

electronic equipment.

(Fig. 10) The product agrees with the applicable

EU directives.

(Fig. 11) The product conforms to the applicable

UK regulations.

(Fig. 12) Direct current.

1728 - 001 - 30.09.2021 5

yyyywwxxxxx The rating plate or the laser

printing shows the serial

number. yyyy is the pro-

duction year and ww is the

production week.

Symbols on the battery and/or on the

battery charger

(Fig. 16)

Recycle this product at a recy-

cling station for electrical and

electronic equipment. (Applies

to Europe only)

(Fig. 13) Fail-safe transformer.

(Fig. 14) Use and keep the battery charger indoors

only.

(Fig. 15) Double insulation.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of

injury or death for the operator or bystanders

if the instructions in the manual are not

obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials or

the adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary

in a given situation.

General power tool safety warnings

WARNING: Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or serious injury.

Note: Save all warnings and instructions for future

reference. The term "power tool" in the warnings refers

to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

Check before starting

• Always remove the battery to prevent the product

being started by accident. Always remove the battery

before any maintenance on the product.

• Before using the product and after any impact, check

for signs of wear or damage and repair as

necessary.

• Inspect the working area. Remove all loose objects,

such as stones, broken glass, nails, steel wire, string

etc. that could be thrown out or become wrapped

around the cutter or cutter guard.

• Check the motor for dirt and cracks. Clean off grass

and leaves from the engine using a brush. Gloves

should be worn when necessary.

• Check that the trimmer head is completely attached

to the trimmer.

• Check that the product is in perfect working order.

Check that all nuts and screws are tight.

• Check that the trimmer head and trimmer guard are

not damaged or cracked. Replace the trimmer head

or trimmer guard if the have been exposed to impact

or are cracked. Always use the recommended guard

for the cutting attachment you are using. See

chapter on Technical data.

• The product operator must ensure that no people or

animals come closer than 15 metres while working.

When several operators are working in the same

area the safety distance should be at least 15

metres.

• Carry out an overall inspection of the product before

use. See the maintenance schedule.

• National or local regulations may regulate the use.

Comply to given regulations.

61728 - 001 - 30.09.2021

Work area safety

•Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

•Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

•Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

Electrical safety

•Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce

risk of electric shock.

•Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

•Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

•Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

•When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

•If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of a RCD reduces the risk of

electric shock.

Personal safety

•Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result

in serious personal injury.

•Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

•Prevent unintentional starting. Ensure the switch is in

the OFF-position before connecting to a power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

•Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in

personal injury.

•Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

•Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

•If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

•Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

• The vibration emission during actual use of the

power tool can differ from the declared total value

depending on the ways in which the tool is used.

Operators should identify safety measures to protect

themselves that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger).

Power tool use and care

•Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it

was designed.

•Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

•Disconnect the plug from the power source and/or

remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the

power tool accidentally.

•Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

•Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool´s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

•Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

•Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

1728 - 001 - 30.09.2021 7

different from those intended could result in a

hazardous situation.

•Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

Battery tool use and care

•Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

•Use products only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

•When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

•Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritations or burns.

•Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion or

risk of injury.

•Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or

temperature above 130 °C / 265 °F may cause

explosion.

•Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified

range may damage the battery and increase the risk

of fire.

Service

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

•Never service damaged battery packs. Service of

battery packs should only be performed by the

manufacturer or authorized service providers.

Always use common sense

It is not possible to cover every conceivable situation

you can face. Always exercise care and use your

common sense. Avoid all situations which you consider

to be beyond your capability. If you still feel uncertain

about operating procedures after reading these

instructions, you should consult an expert before

continuing.

WARNING: Never allow children to use

or be in the vicinity of the machine. Since

the machine is easy to start, children may be

able to start it if they are not kept under full

surveillance. This can mean a risk of serious

personal injury. Therefore disconnect the

battery when the machine is not under close

supervision.

General safety instructions

WARNING: Read the warning

instructions that follow before you use the

product.

• Remove the battery to prevent the product from

being started by accident.

• This product is a dangerous tool if you are not

careful or if you use the product incorrectly. This

product can cause serious injury or death to the

operator or others.

• Do not use the product if it is changed from its initial

specification. Do not change a part of the product

without approval from the manufacturer. Only use

parts that are approved by the manufacturer. Injury

or death is a possible result of incorrect

maintenance.

• Do a check of the product before use. See,

Check

before starting on page 6

and

Before you operate

the product on page 12

. Do not use a defective

product. Do the safety checks, maintenance and

service instructions described in this manual.

• Children should be supervised to ensure that they do

not play with the product. Never allow children or

other persons not trained in the use of the product

and/or the battery to use or service it. Local laws

may regulate the age of the user.

• Keep the product in a locked area to prevent access

for children or persons that are not approved.

• Store the product out of reach of children.

• Under no circumstances may the design of the

product be modified without the permission of the

manufacturer. Always use original accessories. Non-

authorized modifications and/or accessories can

result in serious personal injury or the death of the

operator and others.

Note: National or Local laws can regulate the use.

Comply to given regulations.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use the

product.

81728 - 001 - 30.09.2021

•Do not use the machine in bad weather conditions,

especially when there is a risk of lightning. This

decreases the risk of being struck by lightning.

•Thoroughly inspect the area for wildlife where the

machine is to be used. Wildlife may be injured by the

machine during operation.

•Thoroughly inspect the area where the machine is to

be used and remove all stones, sticks, wires, bones,

and other foreign objects. Thrown objects can cause

personal injury.

•Before using the machine, always visually inspect to

see that the cutter and the cutter assembly are not

damaged. Damaged parts increase the risk of injury.

•Keep guards in place. Guards must be in working

order and be properly mounted. A guard that is

loose, damaged, or is not functioning correctly may

result in personal injury.

•Keep all cooling air inlets clear of debris. Blocked air

inlets and debris may result in overheating or risk of

fire.

•Wear eye protection and ear protection. Adequate

protective equipment will reduce personal injury.

•While operating the machine, always wear non-slip

and protective footwear. Do not operate the machine

when barefoot or wearing open sandals. This

reduces the chance of injury to the feet from contact

with the moving cutter.

•Always wear clothing such as trousers that covers

the operator's legs while operating the machine.

Contact with the moving cutter or line may cause

injury.

•Keep bystanders away while operating the machine.

Thrown debris can result in serious personal injury.

•Do not operate the machine above waist height. This

helps prevent unintended cutter contact and enables

better control of the machine in unexpected

situations.

•Exercise caution when operating the machine in wet

grass. Walk, never run. This reduces the risk of

slipping and falling which may result in personal

injury.

•Do not operate the machine on excessively steep

slopes. This reduces the risk of loss of control,

slipping and falling which may result in personal

injury.

•When working on slopes, always be sure of your

footing, always work across the face of slopes, never

up or down and exercise extreme caution when

changing direction. This reduces the risk of loss of

control, slipping and falling which may result in

personal injury.

•Keep all power cords and cables away from cutting

area. Power cords or cables may be hidden in

hedges or bushes and can be accidentally cut or

damaged by the line or cutter.

•Keep all parts of the body away from the moving

trimmer cutter or line. Do not clear material from the

machine until it has been disconnected from the

power source. The moving trimmer cutter or line may

result in serious personal injury.

•Carry the machine with the machine switched off and

away from your body. Proper handling of the

machine will reduce the likelihood of accidental

contact with a moving trimmer cutter or line.

•Only use replacement cutting heads and trimmer

cutters or lines specified by the manufacturer. Do not

replace the trimmer cutters or lines with metal wires

or blades. Incorrect replacement parts may cause

loss of control, breakage and injury.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use the

product.

• Always use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it

decreases the degree of injury if an accident does

occur. Let your dealer help you select the correct

equipment.

• Use approved hearing protection.

(Fig. 17)

• Use approved eye protection. If you use a visor, you

must also use approved protective goggles.

Approved protective goggles must comply with the

ANSI Z87.1 standard in the USA or EN 166 in EU

countries.

(Fig. 18)

• Use gloves when it is necessary, for example when

you attach, examine or clean the cutting equipment.

(Fig. 19)

• Use protective boots with steel toe-cap and non-slip

soles.

(Fig. 20)

• Use clothing made of a strong fabric. Always use

heavy, long pants and long sleeves. Do not use

loose clothing that can catch on twigs and branches.

Do not use jewelry, short pants or sandals. Do not

go with bare feet. Put your hair up safely above

shoulder level.

• Keep first aid equipment near.

(Fig. 21)

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use the

product.

In this section the product’s safety features, its purpose

and how checks and maintenance should be carried out

to ensure that it operates correctly. See instructions

1728 - 001 - 30.09.2021 9

under the heading

Introduction on page 5

to find where

these parts are located on your product.

The life span of the product can be reduced and the risk

of accidents can increase if product maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest servicing dealer.

WARNING: Never use a product with

defective safety components. The product's

safety equipment must be inspected and

maintained as described in this section. If

your product fails any of these checks,

contact your service agent to get it repaired.

CAUTION: All servicing and repair work

on the machine requires special training.

This is especially true of the machine′s

safety equipment. If your machine fails any

of the checks described below you must

contact your service agent. When you buy

any of our products we guarantee the

availability of professional repairs and

service. If the retailer who sells your

machine is not a servicing dealer, ask him

for the address of your nearest service

agent.

To do a check of the keypad

1. Push and hold the start/stop button (A). (Fig. 22)

a) The product is on when the LED (B) is on.

b) The product is off when the LED (B) is off.

2. Refer to

Keypad on page 15

if the LED (B) flashes.

To do a check of the power trigger lockout

The power trigger lockout prevents accidental start.

When you push the power trigger lockout (A), it releases

the power trigger (B). When you release the handle, the

power trigger and the power trigger lockout move back

to their initial positions.

(Fig. 23)

1. Make sure that the power trigger is locked when the

power trigger lockout is in its initial position. (Fig. 24)

2. Push the power trigger and make sure that it moves

back to its initial position when you release it. (Fig.

25)

3. Make sure that the power trigger and the power

trigger lockout moves freely and that the return

spring works correctly. (Fig. 26)

4. Start the product. Refer to

To start the product on

page 13

.

5. Apply full power.

6. Release the power trigger and make sure that the

cutting attachment stops fully.

To do a check of the cutting attachment guard

WARNING: Do not use a cutting

attachment without an approved and

correctly attached cutting attachment guard.

Always use the recommended cutting

attachment guard for the cutting attachment

that you use, see

Technical data on page

17

. If an incorrect or faulty cutting

attachment guard is attached, it can cause

serious personal injury.

The cutting attachment guard stops objects that eject in

the direction of the operator. The cutting attachment

guard also prevents injuries that can occur if you touch

the cutting attachment.

1. Stop the motor.

2. Do a visual check for damages, for example cracks.

3. Replace the cutting attachment guard if it is

damaged.

Cutting equipment

Select correct cutting equipment and do maintenance on

the cutting equipment to:

• Get maximum cutting performance.

• Increase lifetime of the cutting equipment.

WARNING: Only use cutting

attachments with the guards we

recommend! See

Technical data on page

17

. Refer to the instructions for the cutting

attachment to find the correct way to load

the trimmer line and the correct trimmer line

diameter.

WARNING: A defective cutting

attachment may increase the risk of

accidents.

WARNING: Always stop the engine

before you do the work on the cutting

attachment. This continues to rotate after

you release the throttle. Make sure that the

cutting attachment has stopped fully and

disconnect the spark plug cap before you

start the work on it.

Trimmer head

WARNING: Always make sure the

trimmer line is wound tightly and evenly

around the drum to prevent harmful

vibration.

(Fig. 27)

10 1728 - 001 - 30.09.2021

• Only use recommended trimmer heads and trimmer

lines.

• Only use recommended cutting attachments.

• Smaller machines requires small trimmer heads and

vice versa.

• The length of the trimmer line is important. A longer

trimmer line requires greater engine power than a

shorter trimmer line of the same diameter.

• Make sure that the cutter on the trimmer guard is

intact. This cuts the trimmer line to the correct

length.

• Soak the trimmer line in water for a couple of days

before use to increase the life length.

Battery safety

WARNING: Read the warning

instructions that follow before you use the

product.

• Only use the BLi battery. Refer to

Technical data on

page 17

. The battery is software encrypted.

• Use the BLi battery that is rechargable as a power

supply for the related Husqvarna products only. To

prevent injury, do not use the battery as a power

supply for other devices.

• Risk of electrical shock. Do not connect the battery

terminals to keys, coins, screws or other metal. This

can cause a short circuit of the battery.

• Do not use non-rechargeable batteries.

• Do not put objects into the air slots of the battery.

• Keep the battery away from sunlight, heat or open

flame. The battery can cause burns and/or chemical

burns.

• Keep the battery away from rain and wet conditions.

• Keep the battery away from microwaves and high

pressure.

• Do not try to disassemble or break the battery.

• If the battery leaks, do not let the liquid touch your

body or eyes. If you have touched the liquid, clean

the area with a large quantity of water and soap, and

get medical aid. If you get liquid in your eyes, do not

rub but flush with water for a minimum of 15 minutes

and get medical aid.

• Use the battery in temperatures between -10 °C (14

°F) and 40 °C (114 °F).

• Do not clean the battery or the battery charger with

water. Refer to

To clean the product, the battery and

the battery charger on page 15

.

• Do not use a defective or damaged battery.

• Keep batteries in storage away from metal objects

such as nails, screws or jewelry.

• Keep the battery away from children.

Battery charger safety

WARNING: Read the warning

instructions that follow before you use the

product.

• Risk of electrical shock or short circuit if the safety

instructions are not obeyed.

• Do not use other battery chargers than the one

supplied for your product. Only use QC80 and 40-

C80 chargers when you charge BLi replacement

batteries.

• Do not try to disassemble the battery charger.

• Do not use a defective or damaged battery charger.

• Do not lift the battery charger by the power cord. To

disconnect the battery charger from a mains socket,

pull out the plug. Do not pull the power cord.

• Keep all cables and extension leads away from

water, oil and sharp edges. Make sure that the cable

is not caught between objects, for example, doors,

fences or equivalent.

• Do not use the battery charger near flammable

materials or materials that can cause corrosion.

Make sure that the battery charger is not covered.

Pull out the plug to the battery charger if there is

smoke or fire.

• Only charge the battery indoors in a location with

good airflow and away from sunlight. Do not charge

the battery outdoors. Do not charge the battery in

wet conditions.

• Only use the battery charger where the temperature

is between 5 °C (41 °F) and 40 °C (104 °F). Use the

charger in an environment which has a good airflow,

dry and free from dust.

• Do not put objects into the cooling slots of the

battery charger.

• Do not connect the battery charger terminals to

metal objects as this can short circuit the battery

charger.

• Use approved mains sockets that are not damaged.

Make sure that the cord of the battery charger is not

damaged. If extension cables are used, make sure

that the extension cables are not damaged.

• Do not charge non-rechargeable batteries in the

battery chargers.

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you do

maintenance on the product.

• Remove the battery before you do maintenance,

other checks or assemble the product.

• The operator must only do the maintenance and

servicing shown in this operator's manual. Turn to

your servicing dealer for maintenance and servicing

of a larger extension.

1728 - 001 - 30.09.2021 11

• Do not clean the battery or the battery charger with

water. Strong detergent can cause damage to the

plastic.

• If you do not do maintenance, it decreases the life

cycle of the product and increases the risk of

accidents.

• Special training is necessary for all servicing and

repair work, especially for the safety devices on the

product. If not all checks in this operator's manual

are approved after you have done maintenance, turn

to your servicing dealer. We guarantee that there are

professional repairs and servicing available for your

product.

• Only use original spare parts.

Assembly

Introduction

WARNING: Read and understand the

safety chapter before you assemble the

product.

To attach the trimmer guard

1. Put the trimmer guard against the motor housing.

(Fig. 28).

2. Install the bolt through the motor housing and the

trimmer guard. (Fig. 29)

3. Tighten the bolt.

To assemble the trimmer head

1. Turn the output shaft until the hole in the drive disc

aligns with the hole in the gear housing.

2. Install the locking pin in the hole to lock the shaft.

3. Turn the trimmer head clockwise. (Fig. 30)

To assemble the loop handle

1. Attach the loop handle onto the shaft. (Fig. 31)

2. Move the spacer into the slot of the loop handle.

3. Install the screw and the knob. Do not tighten too

much.

4. Adjust the loop handle to an applicable position.

Refer to

To adjust the loop handle on page 13

.

5. Tighten the knob.

To assemble the two-piece shaft

1. Align the triangle symbol (A) on the shaft with the

triangle symbol (B) on the shaft coupling. (Fig. 32)

2. Push the shaft into the shaft coupling (C). (Fig. 33)

3. Move the shaft coupling sleeve (D) to the shaft

coupling (C). (Fig. 34)

4. Turn and tighten the shaft coupling sleeve fully. (Fig.

35)

To install the plant guard

1. Install the plant guard into the holes on the motor

housing.

2. Make sure that the plant guard can move forward

and rearward freely. (Fig. 36)

Battery information

Refer to the operator's manual of the battery for

information about how to use the battery.

Operation

Introduction

WARNING: Read and understand the

safety chapter before you use the product.

Before you operate the product

• Examine the work area to make sure that you know

the type of terrain. Examine the slope of the ground

and if there are obstacles such as stones, branches

and ditches.

• Do an overhaul of the product.

• Do the safety inspections, maintenance and

servicing that are given in this manual.

• Examine the motor for dirt or cracks. Use a brush to

clean the motor from grass and leaves. Use gloves

when it is necessary.

• Examine the trimmer head and cutting attachment

guard for damages or cracks. Replace the trimmer

head and cutting attachment guard if they are hit or if

they have cracks.

• Make sure that all nuts and screws are tight.

• Make sure that all covers, guards, handles and the

cutting equipment are correctly attached and not

damaged before you start the product.

To connect the battery charger

1. Connect the battery charger to the voltage and

frequency that is specified on the rating plate.

12 1728 - 001 - 30.09.2021

2. Put the plug in a grounded socket outlet. The LED

on the battery charger flashes green one time.

Note: The battery does not charge if the battery

temperature is more than 50 °C/122 °F. If the

temperature is more than 50 °C/122 °F, the battery

charger makes the battery become cool before the

battery charges.

To charge the battery

Note: Charge the battery if it is the first time that you

use it. A new battery is only 30% charged.

1. Connect the battery to the battery charger. (Fig. 37)

(Fig. 38)

2. Make sure that the green charging light on the

battery charger comes on. That means that the

battery is connected correctly to the battery charger.

(Fig. 39) (Fig. 40)

3. When all LEDs on the battery come on, the battery is

fully charged. (Fig. 41)

4. To disconnect the battery charger from the mains

socket, pull the plug. Do not pull the cable.

5. Disconnect the battery from the battery charger.

Note: Refer to the battery and battery charger

manuals for more information.

To connect the battery to the product

WARNING: Only use the initial

Husqvarna battery for the product.

1. Fully charge the battery.

2. Push the battery into the battery holder of the

product. The battery locks into position when you

hear a click. (Fig. 42)

CAUTION: If the battery does not

move easily into the battery holder, the

battery is not installed correctly. This can

cause damage to the product.

To start the product

1. Push and hold the start/stop button until the green

LED comes on. (Fig. 43)

2. Push the power trigger lockout and the power

trigger. The cutting equipment starts to rotate.

To adjust the loop handle

1. Loosen the knob and adjust the loop handle to an

applicable position. (Fig. 44)

Note: Make sure not to attach or move the loop

handle onto the warning decals on the two-piece

shaft.

2. Tighten the knob.

Automatic shutdown function

The product has a shutdown function that stops the

product if the product is not used. The green LED for

start/stop indication goes off and the product stops after

180 seconds.

To operate the product

To trim the grass

1. Hold the trimmer head immediately above the

ground at an angle. Do not push the trimmer line into

the grass. (Fig. 45)

2. Decrease the length of the trimmer line by 9–11 cm/

3.5–4.3 in.

To clear grass

1. Keep the trimmer head above the ground.

2. Tilt the trimmer head.

3. Cut with the end of the trimmer line around objects in

the work area.

CAUTION: Cut grass. Other objects

that are hit by the trimmer line, increases

the wear on the trimmer line.

To cut the grass

1. Make sure that the trimmer line is parallel to the

ground when you cut the grass. (Fig. 46)

2. Do not push the trimmer head to the ground. This

can cause damage to the product.

3. Move the product from side to side when you cut

grass. Use full speed. (Fig. 47)

To sweep the grass

The airflow from the rotating trimmer line can be used to

remove cut grass from an area.

1. Hold the trimmer head and the trimmer line parallel

to the ground and above the ground.

2. Apply full throttle.

3. Move the trimmer head from side to side and sweep

the grass.

WARNING: Clean the trimmer head

cover each time you assemble new trimmer

line to prevent unbalance and vibrations in

the handles. Also do a check of the other

parts of the trimmer head and clean it if

necessary.

1728 - 001 - 30.09.2021 13

To turn the trimmer head

The twist and edge button of the product lets the

operator turn the trimmer head. This makes it easier to

edge along walks or driveways.

(Fig. 48)

1. Push and hold the button while you turn the trimmer

head 90 degrees.

2. Release the button to lock the trimmer head in

vertical position.

To cut the lawn edge

Make sure that the grass trimmer line is vertical to the

ground. Refer to

To turn the trimmer head on page 14

.

(Fig. 49)

• Walk slowly.

• Do not let the trimmer head touch the ground. The

ground and the trimmer head can become damaged.

• Use full power.

• Make sure that the cut material ejects into an area

that was cut before.

To stop the product

1. Release the power trigger and the power trigger

lockout.

2. Push the start/stop button until the green LED goes

off.

3. Push the release buttons on the battery and remove

the battery from the product. (Fig. 50)

To replace trimmer line

Refer to the last page of this operator's manual.

Maintenance

Introduction

WARNING: Read and understand the

safety chapter before you do maintenance

on the product.

Maintenance schedule

WARNING: Remove the battery before

you do maintenance.

The following is a list of the maintenance steps that you

must do on the product. See

Maintenance on page 14

for more information.

Maintenance Daily Weekly Monthly

Clean the external parts of the product with a dry cloth. Do not use water. X

Examine that the start and stop button works correctly and is not damaged. X

Make sure that the power trigger and the power trigger lockout function correctly

from a safety point of view. X

Make sure that all controls work and are not damaged. X

Keep the handles dry, clean and free from oil and grease. X

Make sure that the cutting attachment is not damaged. Replace the cutting at-

tachment if it is damaged. X

Make sure that the cutting attachment guard is not damaged. Replace the cut-

ting attachment guard if it is damaged. X

Make sure that the screws and nuts are tight. X

Make sure that the battery release buttons on the battery works and locks the

battery in the product. X

Examine that the battery charger is not damaged and function correctly. X

Make sure that the battery is not damaged. X

Make sure that the battery is charged. X

14 1728 - 001 - 30.09.2021

Maintenance Daily Weekly Monthly

Make sure that the battery charger is not damaged. X

Examine all cables, couplings and connections. Make sure they are not dam-

aged and free from dirt. X

Do a check of the connections between the battery and the product. Do a check

of the connection between the battery and the battery charger. X

To examine the battery and the battery

charger

1. Examine the battery for damages, for example

cracks.

2. Examine the battery charger for damages, for

example cracks.

3. Make sure that the connection cord of the battery

charger is not damaged and that there are no cracks

in it.

To clean the product, the battery and

the battery charger

1. Clean the product with a dry cloth after use.

2. Clean the battery and battery charger with a dry

cloth. Keep the battery guide tracks clean.

3. Make sure that the terminals on the battery and the

battery charger are clean before the battery is put in

the battery charger or the product.

To examine and replace the trimmer

head

1. Do a check of the trimmer head for damages and

cracks.

2. Pull out the chute assembly for the trimmer line.

3. Remove the trimmer head. (Fig. 51)

4. Replace the trimmer head.

5. Assemble the trimmer head. Refer to

To assemble

the trimmer head on page 12

.

Troubleshooting

Keypad

Problem Possible faults Possible solutions

The LED flashes continuously. Low voltage. Charge battery.

The product does not start. Push the power trigger and press the

start button at the same time.

Release the power trigger and stop

the product.

The LED flashes 3 times again and

again.

Overcurrent. Release the power trigger and start

the product again.

The LED flashes 5 times again and

again.

Temperature deviation. Let the product cool down.

The LED flashes 7 times again and

again.

Logical error. Release the power trigger and start

the product again.

Battery

LED display Possible faults Possible action

The green LED flashes. Low battery voltage. Charge the battery.

1728 - 001 - 30.09.2021 15

LED display Possible faults Possible action

The error LED flashes. Temperature deviation. Use the battery in temperatures between

-10°C (14°F) and 40°C (104°F).

Too much voltage. Make sure that the mains voltage aligns with

the voltage stated on the rating plate of the

product.

Remove the battery from the battery charger.

The error LED is on. Cell difference is too much (1V). Speak to your servicing dealer.

Battery charger

Problem Possible faults Possible solution

Red error LED flashes. Temperature deviation. Use the battery charger in tempera-

tures between 5 °C (41 °F) and 40 °C

(104 °F).

Red error LED comes on. Too much cell difference (1V). Speak to your servicing dealer.

Transportation, storage and disposal

Transportation and storage

• The supplied Li-ion batteries obey the Dangerous

Goods Legislation requirements.

• Obey the special requirement on package and labels

for commercial transportation, including by third

parties and forwarding agents.

• Speak to a person with special training in dangerous

material before you send the product. Obey all

applicable national regulations.

• Use tape on open contacts when you put the battery

in a package. Put the battery in the package tightly

to prevent movement.

• Remove the battery for storage or transportation.

• Put the battery and the battery charger in a space

that is dry and free from moisture and frost.

• Do not keep the battery in an area where static

electricity can occur. Do not keep the battery in a

metal box.

• Put the battery in storage where the temperature is

between 5°C/41°F and 25°C/77°F and away from

open sunlight.

• Put the battery charger in storage where the

temperature is between 5 °C/41 °F and 45°C/113°F

and away from open sunlight.

• Use the battery charger only when the surrounding

temperature is between 5°C/41°F and 40°C/104°F.

• Charge the battery 30% to 50% before you put it in

storage for long periods.

• Put the battery charger in storage in a space that is

closed and dry.

• Keep the battery away from the battery charger

during storage. Do not let children and other not

approved persons to touch the equipment. Keep the

equipment in a space that you can lock.

• Clean the product and do a full servicing before you

put the product in storage for a long time.

• Use the transportation guard on the product to

prevent injuries or damage on the product during

transportation and storage.

• Attach the product safely during transportation.

Disposal of the battery, battery charger

and product

Symbols on the product or the package of the product

means that the product is not domestic waste. Recycle it

at a recycling station for electrical and electronic

equipment. This helps to prevent damage to the

environment and to persons.

Get in touch with your local authorities, domestic waste

service or your dealer for more information about how to

recycle your product.

16 1728 - 001 - 30.09.2021

Technical data

110iL

Motor

Motor type PMDC

Speed of output shaft, rpm 6500

Cutting width, mm 300

Weight

Weight without battery, kg 3.2

Weight with battery (BLi10), kg 4.0

Noise emissions1

Sound power level, measured dB (A) for lawn trimmer 84.7

Sound power level, measured dB (A) for edge trimmer 87.6

Sound power level, guaranteed LWAdB (A) 92

Noise levels2

Equivalent sound pressure level at the operator's ear, measured according to EN ISO

50636-2-91, dB (A) for lawn trimmer:

73.4

Equivalent sound pressure level at the operator's ear, measured according to EN ISO

50636-2-91, dB (A) for edge trimmer:

72.9

Vibration levels3

Vibration levels at handles, measured according to EN50636-2-91, m/s2

Equipped with trimmer head (original), front/rear for lawn trimmer.

1.365 / 1.051

Vibration levels at handles, measured according to EN50636-2-91, m/s2

Equipped with trimmer head (original), front/rear for edge trimmer.

0.873 / 0.789

Approved batteries for the product

Battery BLi10

Type Lithium-ion

1Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive

2000/14/EC. The difference between guaranteed and measured sound power is that guaranteed sound power

also includes dispersion in the measurement result and the varaitaions between different products of the

same model refer to Directive 2000/14/EC.

2Reported data for equivalent sound pressure level for the product has a typical statistical dispersion (standard

deviation) of 2.5 dB (A).

3Reported data for vibration level has a typical statistical dispersion (standard deviation) of 1.5 m/s2.

1728 - 001 - 30.09.2021 17

Battery BLi10

Battery capacity, Ah Refer to battery rating decal Refer to battery rating decal

Nominal voltage, V 36 36.5

Weight, lb/kg 0.7 0.7

Approved battery chargers for the product

Battery charger QC80 40-C80

Mains voltage, V 100-240 100-240

Frequency, Hz 50-60 50-60

Power, W 100 72

Output Voltage, V d.c./ Amps, A 36/2 43/1.6

Accessories

Approved accessories

Approved accessories Type Cutting attachment guard, Art. no.

Trimmer head A15B M6 (Ø 1.5 mm cord) 534 98 40-01

18 1728 - 001 - 30.09.2021

Declaration of Conformity

EU Declaration of conformity

We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:

+46-36-146500, declare on our sole responsibility that

the product:

Description Battery lawn trimmer / Lawn edge trimmer

Brand Husqvarna

Type / Model 110iL

Identification Serial numbers dating from 2021 and onwards

complies fully with the following EU directives and

regulations:

Directive/ Regulation Description

2006/42/EC "relating to machinery"

2014/30/EU ”relating to electromagnetic compability”

2000/14/EC "relating to the noise emissions in the environment"

2011/65/EU “on the restriction of the use of certain hazardous substances in electrical and electronic

equipment ”

and that the following standards and/or technical

specifications are applied: EN

60335-1:2012+A11:2014+A13:2017+A14:2019+A1:2019

+A2:2019, EN 50636-2-91:2014, EN IEC 63000:2018,

EN 55014-1:2017+A11; EN 55014-2:2015.

Notified body: 0197 TÜV Rheinland LGA Products

GmbH, Tillystraße 2, 90431 Nürnberg, Germany has

certified conformity with the council's directive

2000/14/EC, conformity assessment procedure: Annex

VI.

For information relating to noise emission, refer to

Technical data on page 17

.

Huskvarna, 2021-09-30

Pär Martinsson, Development Manager, Husqvarna AB

Responsible for technical documentation

1728 - 001 - 30.09.2021 19

UK Declaration of conformity

We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:

+46-36-146500, declare on our sole responsibility that

the product:

Description Battery lawn trimmer / Lawn edge trimmer

Brand Husqvarna

Type / Model 110iL

Identification Serial numbers dating from 2021 and onwards

complies fully with the following UK regulations:

Regulation Description

S.I. 2008/1597 The Supply of Machinery (Safety) Regulations 2008

S.I. 2016/1091 Electromagnetic Compatibility Regulations 2016

S.I. 2001/1701 The Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001,

Schedule 9

S.I. 2012/3032 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic

Equipment Regulations 2012

and that the following standards and/or technical

specifications are applied: EN

60335-1:2012+A11:2014+A13:2017+A14:2019+A1:2019

+A2:2019, EN 50636-2-91:2014, EN IEC 63000:2018,

EN 55014-1:2017+A11; EN 55014-2:1997+A2:2008.

Approved body: 8500, AnP Certification Ltd. 2 Parkfield

Street, Rusholme, Manchester M14 4PN, UK has

carried out certified conformity according to

S.I.2001/1701.

For information relating to noise emissions, refer to

Technical data on page 17

.

Huskvarna, 2021-09-30

Pär Martinsson, Development Manager, Husqvarna AB

Responsible for technical documentation

UK Importer:

Husqvarna UK Ltd

Preston Road, Co. Durham

DL5 6UP

20 1728 - 001 - 30.09.2021

Pagina se încarcă ...