Yamaha GW33 Manualul proprietarului

Marca: Yamaha

Model: GW33

Categorie: Amplificator de instrumente muzicale

Tip: Manualul proprietarului

GUITAR PERFORMANCE EFFECTOR

OWNER’S MANUAL

This product utilizes batteries or an external

power supply (adapter). DO NOTconnect this

product to any power supply or adapter other than

one described in the manual, on the name pIate,

or specifically recommended by Yamaha.

This Product should be used only with the compo-

nents supplied or; a cart, rack, or stand that is

recommended by Yamaha. If a cart, etc., is used,

please observe all safety markings and instruc-

tions that accompany the accessory product.

SPEClFlCATIONS SUBJECT TO CHANGE:

The information contained in this manual is

believed to be correct at the time of printing.

However, Yamaha reserves the right to change or

modify any of the specifications without notice or

obligation to update existing units.

This product, either aIone or in combination with

an amplifier and headphones or speaker/s, may

be capable of producing sound levels that could

cause permanent hearing loss. DO NOT operate

for Iong periods of time at a high volume level or

at a level that is uncomfortabIe. lf you experience

any hearing Ioss or ringing in the ears, you

should consult an audiologist. lMPORTANT: The

louder the sound, the shorter the time period

before damage occurs.

NOTlCE:

Service charges incurred due to Iack of knowl-

edge relating to how a function or effect

works(when the unit is operating as designed)are

not covered by the manufacturer’s warranty, and

are therefore the owners responsibility. Please

study this manual carefulIy and consult your

dealer before requesting service.

ENVIRONMENTAL lSSUES:

Yamaha strives to produce products that are both

user safe and environmentalIy friendIy. We

sincerely believe that our products and the

production methods used to produce them, meet

these goals . ln keeping with both the letter and

the spirit of the law, we want you to be aware of

the following:

Battery Notice: This product MAY contain a

small non-rechargeable battery which (if

applicabIe)is soldered in PIace. The average life

span of this type of battery is approximately five

years. When repIacement becomes necessary,

contact a qualified service representative to

perform the replacement.

This Product may also use “household”type

batteries. Some of these may be rechargeable.

Make sure that the battery being charged is a

rechargeable type and that the charger is in-

tended for the battery being charged.

When installing batteries, do not mix old batteries

with new, or with batteries of a different type.

Batteries MUST be installed correctly. Mismatches

or incorrect instalIation may result in overheating

and battery case rupture.

Warning: Do not attempt to disassemble, or

incinerate any battery. Keep alI batteries away

from chiIdren. Dispose of used batteries promptly

and as regulated by the laws in your area.

Note: Check with any retailer of household type

batteries in your area for battery disposal informa-

tion.

Disposal Notice: Should this Product become

damaged beyond repair, or for some reason its

useful life is considered to be at an end, pIease

observe aII IocaI, state, and federaI regulations

that relate to the disposal of products that contain

lead, batteries, plastics, etc. if your dealer is

unable to assist you, Please contact Yamaha

directly.

NAME PLATE LOCATlON:

The name Plate is located on the bottom of the

product. The model number, serial number, power

requirements, etc., are located on this plate. You

should record the seriaI number and the date of

purchase in the spaces provided beIow and retain

this manual as a permanent record of your

purchase.

Model GW33

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION (USA)

PLEASE KEEP THIS MANUAL

92-BP

AURAL EXCITER

is a registered trademark and is manufactured under license from Aphex Systems, Ltd.

You are probably eager to try out your new GW33 right

away and hear what it can do, rather than have to read

through a lot of instructions before you can even get a

sound out of it.

Before you do anything else, however, you should read the

PRECAUTIONS

section (page 3). This tells you briefly

how to care for your new GW33, how to avoid damaging

it, and how to ensure long-term, reliable operation.

Next, read the

GW33 SYSTEM OVERVIEW

(page 7).

This provides an important introduction to the internal

organization of the GW33, enabling you to better under-

stand its various functions and use the device to its full

potential.

To actually start using the GW33, read the

GUIDED

TOUR

(page 10). It guides you step-by-step in setting up

your GW33, connecting it properly, and (most impor-

tantly!) getting sound out of it. The section also intro-

duces you to the effect programs by letting you hear what

they are capable of, and explains how to use some of the

other main functions of the device.

The

REFERENCE

section (page 16), on the other hand,

is a comprehensive guide to all functions. You won’t need

(or want) to read through all of it at once, but it is there for

you to refer to when you need information about a certain

feature or function.

The

PANEL CONTROLS AND TERMINALS

(page 4)

is also mainly for reference. In general, look through this

section to familiarize yourself with the controls, and refer

to it when necessary.

The

INDEX

in the

APPENDIX

section (page 40) is also

very helpful. It lists page numbers for virtually every

function, feature, control and terminal found on the

GW33, and lets you find the information you need quickly

and easily.

Other parts of the

APPENDIX

section (page 36) provide

additional useful information: lists of the effect programs

of the GW33, tips on troubleshooting (when something

doesn’t work as expected), and other important informa-

tion.

( READ THIS FIRST!!)

Congratulations and thank you for purchasing the Yamaha GW33 Guitar Performance Effector!

The GW33 is a portable and convenient multi-effect device designed especially for guitar. The comprehen-

sive variety of high-quality effects and convenient Pedal Switch control functions make the highly portable

GW33 ideal for signal processing in home recording, studio, and live performance applications.

Some of the advanced features of the GW33 include:

• Eight independent effect blocks, including Compressor, Distortion/Insert, Equalizer/Amp Simula-

tor, Modulation 1/2, Delay, Reverb, and Noise Gate. The two Modulation blocks allow you to have

two different modulation effects simultaneously.

• A wide variety of high-quality distortion effects, utilizing both analog and digital distortion circuits.

• Twenty-five professionally created Preset effect programs, for use in a wide variety of processing

applications, plus twenty-five User memory locations for saving your own effect programs.

• A separate send/return loop (Insert) for integrating external effects into the GW33 effect chain.

• Convenient parameter control over all effects, yet exceptional ease-of-use — you can adjust the

parameters of the effect blocks much as you would on conventional pedal effects.

• Consistent, continuous Delay/Reverb decay, letting you switch between similarly set programs

without cutting off the Delay/Reverb sound.

• Foot Controller input, for connection of an optional FC7 Foot Controller, giving you convenient

volume control as well as realtime adjustment of the Pedal Wah effect.

• Built-in tuner, allowing you to tune your instrument without removing it from the signal chain.

• Built-in metronome, with fully adjustable time signature and tempo. The metronome provides both

visual indication and an audio click for maximum flexibility.

HOW TO USE THIS MANUAL (READ THIS FIRST!!) . . . . . . . . . . . . . . . . . . . . . . 1

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PANEL CONTROLS AND TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

GW33 SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

GW33 Internal Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

The Effects of the GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

The Effect Structure of the GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Memory Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Effect Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SETTING UP AND PLAYING YOUR GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PLAYING WITH THE EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

EDITING AN EFFECT PROGRAM AND SAVING IT . . . . . . . . . . . . . . . . . . . . . 13

Editing an Effect Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Comparing the Edited Effect Program with the Original . . . . . . . . . . . . . . . . . . 14

Saving an Effect Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

SELECTING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

TURNING ALL EFFECTS OFF — BYPASS FUNCTION . . . . . . . . . . . . . . . . . . . 17

TURNING EFFECT BLOCKS ON AND OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EDITING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Compare Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Parameter Check Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Checking Parameter Values in the Play Mode . . . . . . . . . . . . . . . . . . . . 19

EFFECTS AND PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Compressor Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Distortion/Insert Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Equalizer/Amp Simulator (EQ/AMP) Block . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Amp Simulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Modulation (MOD) 1 and 2 Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chorus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Phaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Pitch Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Detune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

AURAL EXCITER

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Touch Wah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Pedal Wah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Delay Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Reverb Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Noise Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

FOOT CONTROLLER OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Setting the Volume Position and Minimum Volume . . . . . . . . . . . . . . . . . . . . . 30

Using the Foot Controller for Pedal Wah Control . . . . . . . . . . . . . . . . . . . . . . . 30

TOTAL LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

SAVING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

COPY AND SWAP OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Copying One Effect Program to Another Program Number . . . . . . . . . . . . . . . 32

Swapping One Effect Program with Another . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Restoring Factory-set Effect Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

TUNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Tuning the Pitch of the Connected Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Changing the Standard Pitch of the Tuner Function . . . . . . . . . . . . . . . . . . . . . . 35

METRONOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

BLANK EFFECT PARAMETER CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

■ USE THE CORRECT POWER SUPPLY

Power to the GW33 should be supplied only from the

appropriate Yamaha AC adaptor (the PA-3, or another

adaptor recommended by Yamaha). Use of another

adaptor may cause serious damage to the unit. (Never use

the PA-3B.) Also make sure that the adaptor you have is

appropriate for the AC mains supply voltage in the area

where you intend to use the GW33. (The correct input

voltage is marked on the adaptor.)

■ AVOID EXCESSIVE HEAT, HUMIDITY, DUST

AND VIBRATION

Keep the unit away from locations where it is likely to be

exposed to high temperatures (such as direct sunlight) or

humidity. Also avoid locations which are subject to

excessive dust accumulation or vibration which could

cause mechanical damage.

■ AVOID PHYSICAL SHOCKS

Although the GW33 has been constructed to withstand the

normal rigors of stage and studio use for optimum sturdi-

ness and reliability, avoid subjecting it to strong physical

shocks (such as dropping or hitting it), since this may

damage the unit. Since the GW33 is a precision-made

electronic device, also avoid applying excessive force to

the various controls.

■ DO NOT OPEN THE CASE OR ATTEMPT

REPAIRS OR MODIFICATIONS YOURSELF

This product contains no user-serviceable parts. Refer all

maintenance to qualified Yamaha service personnel.

Opening the case and/or tampering in any way with the

internal circuitry will void the warranty.

■ MAKE SURE POWER IS OFF BEFORE MAK-

ING OR REMOVING CONNECTIONS

Always turn the power off prior to connecting or discon-

necting cables.

■ HANDLE ALL CONNECTIONS CAREFULLY

Always be careful to connect and disconnect all cables and

cords by gripping the connector itself, not by pulling on

the cord.

■ CLEAN WITH A SOFT, DRY CLOTH

Never use solvents such as benzine or thinner to clean the

unit, since these will damage the finish. Wipe clean with a

soft, dry cloth. If necessary, use a soft, clean slightly

moistened cloth — making sure to wipe the case off again

with a dry cloth.

■ ELECTRICAL INTERFERENCE

Since the GW33 contains digital circuitry, it may cause

interference and noise if placed too close to TV sets,

radios or similar equipment. If such a problem occurs,

move the GW33 further away from the affected equip-

ment.

This section shows and explains all of the controls and terminals of the GW33. Since the expla-

nations below are fairly brief, you should turn to the page references given for more information

on individual buttons and features. Refer to this section also as necessary when using the GW33,

when you need specific information on a certain control or terminal.

■ TOP PANEL

•••••••••••••••••••••••••••••••••••••••••••••••••

•••••••

COMP

DIST /

INSERT

EQ / AMP

DELAY

REVERB

N.GATE/UTIL

TUNER/

METRONOME

MOD 2

MOD 1

ATTACK

PRE-DRIVE*

LOW / —

TIME

THRESHOLD

SPEED

PITCH

PITCH L

ENHANCE

SENSE

DRIVE

MID / —

TONE

VOLUME POSITION

BEAT

(14~88 = 1/4~8/8)

DEPTH

— / PITCH R

FREQUENCY

—

TONE

HIGH / TONE

MIX

MINIMUM VOLUME

TEMPO

(60~86.=60~186)

TONE / FB

MIX

MIX / RANGE

LEVEL

TOTAL LEVEL

CLICK LEVEL

(1 LO 2 MID 3 HI)

ON/OFF

(SWITCH 4)

1 EQ / 2 STACK 3 COMBO 4 TUBE

————---

1~3

OD, DIST1,2 (DI*+AN)

4,5 OD*+DIST1,2

6~11 OD, DIST1,2+INSERT 12 INSERT

————---

TUNING PITCH

(0~5

440~445Hz)

1 CHORUS / 2 FLANGER 3 PHASER

4 PITCH SHIFT / 5 DETUNE

6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH

1 HALL 2 ROOM 3 STAGE 4 PLATE

ON/OFF

(SWITCH 5)

ABCDE

COPY / SWAP / WRITE

MEMORY NO.

TUNER

–20

– 5

+ 5

+20

PLAY

COPY

SWAP/

WRITE

EDIT/

COMPARE

METRONOME

•

••••

•

PITCH SHIFT

±1 = 3rd

±2 = 3rd

±3 = 4th

±4 = 5th

±5 = 5th

±6 = 6th

±7 = 7th

±8 =

OCTAVE

DELAY TIME

10 ~ 90 =

10 ~ 90ms

10.~ 81.=

100 ~ 810ms

ON / OFF

1 EFFECT OFF

2 EFFECT ON

3 SWITCH

VOLUME POSITION

1 DIST

2 DELAY

3 REVERB

4 REVERB

DISTORTION / INSERT

1 OVERDRIVE

2 DISTORTION

3 DISTORTION

→INSERT

1→INSERT

2→INSERT

INSERT→OD

INSERT→DS

4 OD + DIST

5 OD + DIST

12 INSERT

COMPRESSOR DIST / INSERT EQ / AMP MOD 1 MOD 2 DELAY REVERB

TUNER

HOLD

GUITAR PERFORMANCE EFFECTOR

YES

BANK MEMORY

••••

•

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••

••••••

•

••••••

••

••••

••

••••

BYPASS

••

••••

••

••••

—

TWIN DRIVE OVERDRIVE & DISTORTION

DUAL MODULATION WITH AURAL EXCITER

INTEGRATED INSERTION LOOP

BUILT-IN TUNER & METRONOME

ON OFF

••••••••••••••••••••••

PARAM

CHECK

•

ewq r t y

o !1!0 !2

q COPY, SWAP/WRITE Buttons

These two buttons call up the Copy and Swap/Write

operations, respectively. (See pages 32 and 33.) Copy

and Swap are called up from the Play mode, while

Write is called up from the Edit mode. The COPY and

SWAP/WRITE lamps are lit when the respective Copy

or Swap/Write operation is active.

When pressed together simultaneously, these buttons

start the built-in Metronome function. When the

Metronome is on, the lamps of the two buttons flash in

time with the audio click. (See page 35.)

w PLAY Button

Enables the Play mode, from which the effect programs

can be selected and played.

e BANK/MEMORY Indicator

Displays the program number. During Tuner operation,

this displays the name of the note or string played. (See

page 34.) The LED dot (#) at the bottom right serves as

a sharp indicator during Tuner operation (functioning

along with the note name shown in the BANK/

MEMORY indicator), and lights to indicate values of

100 and higher.

r EDIT/COMPARE Button

For enabling the Edit mode, from which the selected

effect program can be edited. In the Edit mode, this

also serves as a Compare switch for toggling between

the newly edited settings and original settings of an

effect program.

t Effect Parameter/Tuner Lamps

In the Edit mode:

These indicate the effect block and

parameters currently selected for editing. (See

page 13.)

In the Play mode:

These indicate the effect block

currently selected for checking parameter

values. (See page 19.)

In the Tuner mode:

These indicate whether the input

signal is in tune or not; when the center lamp (to

the right of 0) flashes, the signal is in tune. (See

page 34.)

y YES/ and NO/ Buttons

In the Edit mode:

These are used to select an effect

block (and its parameters) for editing. (See page

13.)

When pressed together (in the Edit mode):

These call

up the Parameter Check mode, for checking the

currently edited parameter values. (See page

19.) Pressing one of the buttons again returns to

normal editing.

In the Play mode:

These are used to select the effect

block for checking parameter values. (See page

19.)

In the Copy, Swap and Write operations:

These are

used to execute (YES) or cancel (NO) the

respective operation.

u TUNER Button

For enabling the Tuner mode (from the Play mode).

(See page 34.) Pressing the button again returns to the

Play mode.

i Effect Block ON/OFF Lamps

These light when the corresponding effect block is on.

o Pedal Switches 1 – 5

In the Play mode:

When the ON/OFF lamp (above

Pedal Switch B) is off, these are used to select

effect programs. (See page 12.)

In the Edit or Play modes:

When the ON/OFF lamp

(above Pedal Switch B) is flashing, these are

used to turn individual effect blocks on or off.

(See page 17.)

Also, pressing Pedal Switches 1 and 2 together simulta-

neously enables the Tuner mode. (See page 34.)

Pressing Pedal Switches 2 and 3 together simulta-

neously enables the Bypass function. (See page 17.)

!0 Parameter Dials

For selecting the effect type and adjusting the param-

eters of a selected effect. The parameters in a single

column correspond to the dial in that column.

!1 Pedal Switch B (Bank)

In the Play mode:

Pressing this once enables selection

of banks 1 – 5. Holding this down enables

selection of banks 6 – 0.

Pressing this twice quickly enables effect block on/off

switching. (See page 17.)

!2 ON/OFF Mode Lamp

This flashes to indicate that Pedal Switches 1 – 5 can be

used to turn individual effect blocks on or off.

■ REAR PANEL

POWER

ON OFF DC IN INPUT SEND RETURN

INSERT

OUTPUT

L / MONO

PHONES

FOOT

CONTROLLER

q w e r y ut

q POWER ON/OFF Switch

w DC IN Terminal

For connection to the PA-3 AC adaptor (or another

adaptor recommended by Yamaha). (Never use the

PA-3B.) Wrap the adaptor cord firmly around the cable

clip as shown, to prevent accidental unplugging of the

power cord during use.

t L/MONO and R OUTPUT Jacks

For stereo or mono output of the instrument and metro-

nome sound. Connect both of these to the corresponding

left and right channels of your stereo amplification system

to take full advantage of the stereo effects of the GW33.

For mono operation, connect your system only to the L/

MONO jack; this provides a mono mix of the instrument

sound when the R OUTPUT jack is not connected.

y PHONES Jack

For stereo output of the guitar/effect and metronome

sound to a set of stereo headphones.

u FOOT CONTROLLER Jack

For connection of an optional foot controller (use ONLY

the Yamaha FC7), for controlling the volume or the Pedal

Wah effect. (See page 30.)

AC adaptor

Cable clip

DC IN

e INPUT Jack

For connection of an instrument (guitar, bass, etc.). (See

page 10 for more information on input/output connec-

tions.)

r INSERT SEND and RETURN Jacks

For connection of an external effect device or devices.

Use the SEND jack to output the signal from the GW33,

and use RETURN to input the signal from the external

effect device(s).

This section provides a brief overview of the GW33 — the basic structure of its various functions

and the memory system. Once you gain a general understanding of the internal workings of the

GW33 as given here, you’ll have the tools for taking full advantage of its features.

The diagram below shows the internal system of the

effects and other functions of the GW33.

The GW33 is equipped with a comprehensive set of

effects designed specifically for the guitar player. Up to

eight different effects can be used simultaneously. More-

over, a special Insert block lets you connect additional

external effect units to the multi-effect chain of the GW33.

Individual effects (excepting Noise Gate) can be turned on

and off as needed with the Pedal Switches and can be

quickly and easily adjusted with the Parameter Dials.

There are eight main effect blocks and a total of thirty-one

different effect types:

(Refer to the EFFECTS AND PARAMETERS section,

page 20, for more detailed descriptions and explanations

of these effects.)

With all these various effects, used individually or simul-

taneously, the GW33 has all you need to augment your

sound, whatever the application. Plus, flexible effect

bypass (on/off) functions give you even more realtime

control over the sound. A programmable Noise Gate is

also included for filtering out hum, hiss and other undesir-

able noise. (See page 29.)

The Effects of the GW33

Effect Block

Compressor

Distortion/Insert

Equalizer/

Amp Simulator

Modulation 1

Modulation 2

Delay

Reverb

Noise Gate

Effect Type

Compressor

Overdrive, Distortion 1,

Distortion 2, Overdrive + Distortion 1,

Overdrive + Distortion 2, Overdrive → Insert,

Distortion 1 → Insert, Distortion 2 → Insert,

Insert → Overdrive, Insert → Distortion 1,

Insert → Distortion 2, Insert

Equalizer, Stack Amp Simulator,

Combo Amp Simulator, Tube Amp Simulator

Chorus, Flanger, Phaser, Pitch Shift,

Detune, Exciter, Touch Wah, Pedal Wah

(Same as Modulation 1; effects can be used

independently.)

Delay

Hall, Room, Stage, Plate

Noise Gate

GW33 Internal Structure

* Use the optional YAMAHA Foot Controller FC7.

INPUT

INSERT

SEND

INSERT

RETURN

WAH

COMP

DIST /

INSERT

N.GATE EQ / AMP DELAY MOD 1 REVERB

OUTPUT

L/MONO

MOD 2

TOTAL

LEVEL

CLICK

LEVEL

TUNER

BYPASS

METRONOME

Volume

Pedal

(Position 2)

Volume

Pedal

(Position 1)

Volume

Pedal

(Position 3)

Volume

Pedal

(Position 4)

(when

Touch Wah

or Pedal

Wah is

selected)

MOD 1, 2 Block

Headphones

Wah

Pedal

The Effect Structure of the GW33

Keep in mind as you use the GW33 that the structure of its

effects is basically in a four-part hierarchy: 1) Effect

programs, 2) Effect blocks, 3) Effect types, and 4) Effect

parameters.

An effect program consists of eight different effect blocks,

all of which can be used simultaneously. A block includes

one or more effect types, one of which can be used at a

time. And each effect type has up to four different param-

eters, which allow you to set the sound of the effect. The

logic of this structure is reflected in the panel layout, with

effect blocks, types and parameters printed in a matrix

from left to right.

Memory Structure

The GW33 has a total of 50 effect programs, divided into

ten banks of five programs each. The 25 programs from

61 – 05 are Preset programs. Programs 11 – 55 are User

programs, and your own original settings can be stored to

these.

•••••••••••••••••••••••••••••••••••••••••••••••••

COMP

DIST /

INSERT

EQ / AMP

DELAY

REVERB

N.GATE/UTIL

TUNER/

METRONOME

MOD 2

MOD 1

ATTACK

PRE-DRIVE*

LOW / —

TIME

THRESHOLD

SPEED

PITCH

PITCH L

ENHANCE

SENSE

DRIVE

MID / —

TONE

VOLUME POSITION

BEAT

(14~88 = 1/4~8/8)

DEPTH

— / PITCH R

FREQUENCY

—

TONE

HIGH / TONE

MIX

MINIMUM VOLUME

TEMPO

(60~86.=60~186)

TONE / FB

MIX

MIX / RANGE

LEVEL

TOTAL LEVEL

CLICK LEVEL

(1 LO 2 MID 3 HI)

ON/OFF

(SWITCH 4)

1 EQ / 2 STACK 3 COMBO 4 TUBE

————---

1~3

OD, DIST1,2 (DI*+AN)

4,5 OD*+DIST1,2

6~11 OD, DIST1,2+INSERT 12 INSERT

————---

TUNING PITCH

(0~5

440~445Hz)

1 CHORUS / 2 FLANGER 3 PHASER

4 PITCH SHIFT / 5 DETUNE

6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH

1 HALL 2 ROOM 3 STAGE 4 PLATE

ON/OFF

(SWITCH 5)

ABCDE

COPY / SWAP / WRITE

MEMORY NO.

YES

•••••

••••••

•

••••••

—

••••••••••••••••••••••

PARAM

CHECK

•

Effect Block

These are used to

select the effect

block.

This is used to

select the

effect type.

These are used to change the

parameters in the corresponding

columns.

Effect Types

Effect Parameters

Preset Programs

Bank 6 Bank 7 Bank 8 Bank 9 Bank 0

User Programs

Bank 1 Bank 2 Bank 3 Bank 4 Bank 5

Sound Character

Main Sub

Effect Programs

Sound Character

Main Sub

Programmer’s comments

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Over

Drive

Dist

Hard

Dist

Softer

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Hard

Dist

Softer

Over

Drive

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Hard

Over

Drive

Clean

Dist

Hard

Dist

Softer

Clean

S.E.

—

Detune

—

Detune

Flanger

Chorus

—

Wah

Chorus

Detune

Phaser

—

Detune

—

Detune

Phaser

Flanger

Detune

—

Touch

Wah

—

Detune

Chorus

—

Detune

—

Chorus

Detune

—

Touch

Wah

Pitch

Detune

Chorus

Detune

—

Flanger

—

Phaser

Detune

—

Detune

—

Detune

Chorus

Pitch

Pedal

Wah

Detune

Pedal Wah

Flanger

Touch Wah

Chorus

Phaser

Digital and analog distortion for rock

solos.

Analog overdrive + distortion; good

for pop music.

Natural overdrive for rock’n’roll.

Clean sound, good for wide range of

styles (ex., blues, funk, jazz).

Clear sound with flanger and chorus.

Heavy distortion sound with en-

hanced low and high frequencies.

Distortion sound for backing.

Spacious overdrive sound for fusion.

Natural reverb sound from the 50’s.

Dynamics “squashed” with compression.

Tremolo sound.

Digital + analog overdrive for rock

or fusion.

Powerful sound, good for rock

ballads.

Overdrive sound for rock leads.

Mellow, round sound.

Clean sound for rhythmic play.

Hard distortion sound with enhanced

attack; for rock leads.

Distortion sound with detuning, for

rock backing.

“Dry” overdrive.

Multi-purpose program for a wide

variety of styles.

Touch Wah program, good for funk,

jazz, blues, etc.

Hard digital + analog distortion

sound for direct recording.

Hard distortion program, with stack

amp sound, for direct recording.

Warm overdrive sound for direct

recording.

Clear, distinct sound with detuning

and delay, for direct recording.

Clean sound for direct recording.

Distortion especially for rock solos.

Digital + analog distortion, plus EQ,

for heavy metal.

Detune and reverb for a “wet” solo

sound.

Natural, warm overdrive.

Clean, spacious sound with Cho./

Detune/Delay/Reverb mix.

Hard, metallic lead.

Dynamically responds to your

plucking technique.

Stereo pitch shift: 5th above and

below.

Clean and dreamy with long delay.

Soft, clean sound, ideal for soloing or

rhythmic chords.

Analog overdrive + distortion —

hard-edged for backing.

Analog + digital distortion, plus

flanger and delay.

Bright overdrive with delay for

American hard rock leads.

British 60’s rock sound — simple

and straight.

70’s fusion sound, with heavy

phaser.

Hard distortion for rock soloing.

Slightly bright distortion for hard

rock backing.

Crunch sound with enhanced low

and high frequencies.

Good, clear sound for rhythmic

playing.

Ideal for funky rhythmic playing or

arpeggios.

Hard distortion sound, with pitch an

octave below.

Hard crunch sound for rhythmic

playing; with Pedal Wah.

Mellow sound for rhythmic play.

Sound effect with dynamic response

to plucking technique.

Chorus sound with stereo phaser.

Once you’ve taken your GW33 out of the box and are ready to use it, you’ll have to make a few

connections and follow some simple instructions on setting it up.

GUIDED TOUR

When using your GW33 for the first time, read through this short section of the

manual. It guides you step-by-step in all basic operations: setting the instrument

up, connecting it properly to other equipment, and playing the effect programs.

POWER

ON OFF DC IN INPUT SEND RETURN

INSERT

OUTPUT

L / MONO

PHONES

FOOT

CONTROLLER

OUT IN

Plug into a

suitable AC

outlet

PA-3

power adaptor

Use only this

adaptor or

another Yamaha

recommended

adaptor.

Wrap the adaptor cord around the

cable clip to prevent accidintal

unplugging.

Electric guitar

Optional FC7

Foot Controller

(for Volume pedal

and Pedal Wah

control).

External effect unit

Guitar amplifier

(left channel)

Guitar amplifier

(right channel)

Headphones

Signals are output through

the OUTPUT jacks, even

when headphones are

connected.

Adjust the headphone

volume with the Total Level

parameter (see page 31).

When using a single guitar amp, connect to

the L/MONO OUTPUT jack.

First, make sure that the power switch on the GW33

is off before making ANY connections.

Plug the DC output cable from the supplied PA-3

adaptor (or another adaptor recommended by

Yamaha) (Never use the PA-3B.) into the DC IN

terminal on the rear panel, then plug the adaptor into

a convenient AC outlet.

The cable clip located next to this terminal helps to

prevent accidental unplugging of the power supply

during use. Wrap the adaptor cord firmly around the

clip (see the Rear Panel illustration, page 10).

CAUTION! ■

Do not attempt to use a different

AC adaptor with the GW33. (See the precaution

on page 3.)

Plug your instrument into the INPUT jack on the rear

panel.

For the sake of these instructions, we’ll assume

you’re using an electric guitar; however, most any

electronic instrument can be used.

NOTE ■

You should be careful if you are connecting

a synthesizer or electronic keyboard. Since their

output level is generally much higher than that of a

guitar, the volume control on the instrument should

be turned down accordingly.

Connect the GW33 output or outputs to your ampli-

fier/speaker system, as shown on page 10. Before

you do this, however, make sure that the power on

the system is first turned off and all volume controls

are set to zero — this includes the guitar controls and

the volume on the connected amp(s).

NOTE ■

Use the clean channel of the amplifier for

best results.

If you are using an optional FC7 Foot Controller

with the GW33, connect it to the FOOT CONTROL-

LER input jack on the rear panel. Make sure that the

pedal is at or near the maximum position.

Turn on the power of all the equipment, starting with

the GW33, and turning on the connected amplifier

last.

Before you turn up the volume and try to play, set all

the effects to off by using the Bypass function.

To do this, simultaneously press and hold down

Pedal Switches 2 and 3. Keep holding them down

(for roughly one second) until “bP” (Bypass)

appears in the BANK/MEMORY indicator.

This temporarily turns off all effect processing, and

lets you hear the “dry” input signal.

Now, set your guitar to a suitable volume. Next,

slowly bring up the level of the connected amplifier

as you play, until the level is suitable.

Finally, turn the Bypass function off by pressing any

one of the Pedal Switches (1 – 5 or B).

If you’ve followed all these instructions carefully,

you should now be able to hear the sound of your

guitar processed by the effects of the GW33, and are

able to try out some of the other effect programs of

the GW33. If no sound is output or the sound isn’t as

you expect, refer to the Troubleshooting section on

page 36.

DIST / INSERT EQ / AMP

BYPASS

••

••••

••

••••

•••••••

BANK MEMORY

Firmly press and hold these

down for about one second.

Now that you’ve set up your GW33 and have got sound out of it, let’s try playing with some of

the effects. (If you haven’t already done so, read through the GW33 SYSTEM OVERVIEW

section on page 7 for information on the basic structure of the GW33.)

First, make sure that the Play mode is enabled. Press

To change the bank, use the Bank (B) Pedal Switch.

To select one of banks 1 – 5, press it once, then press

the appropriate Pedal Switch 1 – 5.

Let’s start with a clean chorus/delay effect. Use

Pedal Switch 5 to select program number 15.

PLAY

DELAY REVERB

•••••••

BANK MEMORY

DIST / INSERT

•••••••

BANK MEMORY

HOLD

ON OFF

Press this once... ...then press one

of these to select

bank 1 – 5.

1 – 5

To select one of banks 6 – 0, hold the Bank Pedal

Switch down and simultaneously press the appropri-

ate alternate numbered Pedal Switch 6 – 0.

Now that you know how to select banks and pro-

grams, try exploring some of the other effect pro-

grams of the GW33. Look through the Effect

Programs list on page 9 for more information about

the programs, and play with a few of them to hear

how they sound.

COMPRESSOR

•••••••

BANK MEMORY

HOLD

ON OFF

While holding

this down...

...press one of

these to select

bank 6 – 0.

6 – 0

NOTE ■

If you’re using the FC7 Foot Controller,

make sure that it is at or near the maximum position

to ensure proper volume.

Next, try a heavy distortion sound. Press Pedal

Switch 2 to select program number 12.

DIST / INSERT

•••••••

BANK MEMORY

Notice that all the program numbers have two digits.

The first digit indicates the bank and the second

indicates the program number. By pressing one of

the Pedal Switches 1 – 5, you can select one of five

programs in the currently selected bank.

The GW33 makes it extremely easy to adjust or change the sound of the effects. In this section,

you’ll learn how to change the effect type and use the Parameter Dials to change effect settings.

You’ll also learn how to compare the edited program with the original. Finally, you’ll learn how

save the new effect program you’ve created.

Editing an Effect Program

Select one of the User or Preset effect programs.

Although any effect program will do, select

program number 11 for this example.

NOTE ■

The on/off switching of the MOD 1/2 and

Delay/Reverb blocks is determined by the On/Off

parameter of those blocks. (See pages 24 and 27.)

Use the y and n buttons to select the

desired effect block row (in the parameter matrix

printed on the panel). (The lamp at the left of the

corresponding block lights.) For this example, press

either button repeatedly until the Distortion/Insert

block is selected.

NOTE ■

Even though creating and saving your own

effect program erases the previously stored program,

you can restore that particular factory Preset pro-

gram. Refer to RESTORING FACTORY-SET

EFFECT PROGRAMS on page 33 for details. Keep

in mind, however, that restoring the factory Preset

program will irretrievably erase the effect you’ve

created. For this reason, you may want to keep a

written record of the settings you make (using a copy

of the Blank Effect Parameter Chart on page 38), so

that you can reprogram the effect later if necessary.

Next, press the e button to enable

the Edit mode. (The EDIT/COMPARE lamp

lights and the ON/OFF lamp above the Bank Pedal

Switch flashes.)

•••••••

BANK MEMORY

Press the Bank (B) Pedal Switch once, and press Pedal

Switch 1 to select Bank 1. Then, press Pedal Switch 1

again (if needed) to select program number 11.

HOLD

ON OFF

COMPRESSOR COMPRESSOR

NOTE ■

The TUNER/METRONOME row cannot be

selected in the Edit mode.

Use the Parameter Dials to adjust the effect

parameters. For example, if you want to change the

amount of Pre-drive in the Distortion effect (selected

above), adjust Parameter Dial B.

COMP

DIST /

INSERT

EQ / AMP

MOD 2

MOD 1

1 EQ /

————---

1~3

6~11 OD

1 CHOR

4 PITCH

6 EXCIT

YES

•••••

••••••

•

••••••

••••••••••••••••••••••

PARAM

CHECK

•

Parameter Dial A is used to change the effect type of

the selected block; B – E are used to change the

corresponding parameters.

If you wish, you can simply view the parameter

values that you are currently editing (without

changing them) by using the Parameter Check

mode. (See page 19 for details.)

For information about each of the effects and their

parameters, refer to the section EFFECTS AND

PARAMETERS on page 20.

Press this.

EDIT/

COMPARE

Press this to turn Distortion

block on or off. (The lamp

lights when the block is on.)

DIST / INSERT

DIST / INSER

OFF

Notice that the ON/OFF lamp above the Bank Pedal

Switch flashes. This means that you can turn indi-

vidual effect blocks on and off.

Try turning an effect block on and off now; press

Pedal Switch 2 to turn the Distortion block on or

off.

Comparing the Edited Effect Program with the Original

You can compare the sound of the newly edited program

with the sound of the original one. To do this, press the

e button again (so that the EDIT/COM-

PARE lamp flashes).

EDIT/

COMPARE

EDIT/

COMPARE

In this condition, you can hear the sound of the original

effect program. You can also view the original parameter

values by selecting the desired effect block with the

y or n buttons and turning the Parameter

Dials. Doing this doesn’t change the value, it simply

displays it so that you can check it against the value

you’ve edited.

Each press of the e button switches back

and forth between the original program (lamp flashes) and

your new edits (lamp lights continuously).

When you’ve adjusted the sound to your satisfaction, you

may wish to save it for future recall. You can either copy

the settings down on paper (using a copy of the Blank

Effect Parameter Chart on page 38) or go on to the next

section and save the settings to the GW33’s memory.

CAUTION! ■

Be careful not to press the

button while editing. If you do, the original effect

program’s settings will be called up, erasing all

settings you had made to that point.

Saving an Effect Program

Now that you’ve created your own original effect pro-

gram, you will want to save the settings to a program

number, so that you can recall your new effect program in

the future. (For more information on saving effect pro-

grams and other matters relating to memory, see the

SYSTEM OVERVIEW section on page 7.)

If you’ve continued from the last section and have

new settings you want to save, press the

s button.

The SWAP/WRITE lamp lights and the program

number in the BANK/MEMORY indicator flashes

to indicate that the GW33 is ready to write the

settings to memory at the selected program number.

If you want to save the program to the current

number, skip to step #3. If you want to select a

different program for saving the new program, go to

the next step.

NOTE ■

Edited programs can be saved to the User

effect programs, in banks 1 – 5. Banks 6 – 0 are

reserved for the Preset effect programs, and cannot

be used to save edited programs.

NOTE ■

When you’ve edited one of the Preset

programs (61 – 05) and try to save it, “—” appears in

the BANK/MEMORY indicator until you select one of

the User program numbers (11 – 55).

If desired, select the destination User program

number (11 – 55) by using Parameter Dial A.

Keep in mind that the programs that you edit can

only be saved to one of the User program numbers,

and not to the Preset program numbers.

To actually save the new settings, press the

y button. (Operation returns to the Edit

mode.)

SWAP/

WRITE

SWAP/

WRITE

•••••••

BANK MEMORY

This concludes your short tour of the important functions of the GW33. To find out

more about how to best use your GW33, look through the Reference section and read

about some of the functions that interest you.

•••••••

BANK MEMORY

YES

•••••

••••••

•

••••••

•••••••••••••

PAR

CHE

•

To cancel the operation without saving, press the

n button.

Pressing n returns to the program that you’ve

been editing. The settings are saved temporarily, and

you can continue editing the program.

YES

•••••

••••••

•

••••••

••••••••••••••••••••••

PARAM

CHECK

•

OPERATION

With the Play mode enabled (press p ), first

select the desired bank of programs.

● To select one of banks 1 – 5

To select one of banks 1 – 5, press the Bank Pedal

Switch once, then press the appropriate Pedal Switch 1

– 5.

REFERENCE

This section of the manual explains briefly, yet completely, all of the features and

functions of the GW33. Refer to it when you need information about a specific

feature or function.

With the bank now selected, press one of Pedal

Switches 1 – 5 to select the desired program.

Refer to the Effect Programs list on page 9 for more

information on the programs of the GW33.

•••••••

BANK MEMORY

DELAY REVERB

You can continue to select other programs in the same

bank by pressing the other Pedal Switches.

User programs are in banks 1 – 5, and Preset programs

are in banks 6 – 0. Each bank contains five programs.

Preset Programs

Bank 6 Bank 7 Bank 8 Bank 9 Bank 0

User Programs

Bank 1 Bank 2 Bank 3 Bank 4 Bank 5

● To select one of banks 6 – 0

To select one of banks 6 – 0, hold the Bank Pedal

Switch down and simultaneously press the appropriate

alternate numbered Pedal Switch 6 – 0.

•••••••

BANK MEMORY

DIST / INSERT

HOLD

ON OFF

Press this once... ...then press one

of these to select

bank 1 – 5.

1 – 5

•••••••

BANK MEMORY

COMPRESSOR

HOLD

ON OFF

While holding

this down...

...press one of

these to select

bank 6 – 0.

6 – 0

While playing, you can instantly get a clean, unprocessed sound by using the Bypass function.

This effectively cancels all currently active effects to give you a “dry” sound.

● To use the Bypass function:

Simultaneously and firmly press and hold down Pedal

Switches 2 and 3. Keep holding them down (for roughly

one second) until “bP” (Bypass) appears in the BANK/

MEMORY indicator.

Now, when you play your guitar, you should hear the

guitar sound unprocessed by the effects.

NOTE ■

If a Foot Controller has been connected, it is

also disabled when Bypass is on.

To return to normal Play mode operation and the current

effect program, press any one of Pedal Switches 1 – 5 or

Pedal Switch B.

NOTE ■

As you press and hold Pedal Switches 2 and 3,

the BANK/MEMORY indicator may briefly show the

program number corresponding to one of those switches.

However, the program you selected before using Bypass

remains selected, and is the one returned to when turning

Bypass off.

DIST / INSERT EQ / AMP

BYPASS

••

••••

••

••••

•••••••

BANK MEMORY

Firmly press and hold these

down for about one second.

In the Play or Edit modes, any of the main effect blocks can be individually turned on or off with

the Pedal Switches. (Switching of Modulation 1/2, and Delay/Reverb is dependent on the On/Off

settings of those effect blocks; see pages 24 and 27.)

OPERATION

With the Play mode enabled (press the p

button if necessary), press Pedal Switch B twice

quickly so that the lamp above the Pedal Switch

flashes. This same condition is called up automati-

cally when entering the Edit mode.

Press the appropriate Pedal Switch to turn the

desired effect block on or off. (The lamp above the

Pedal Switch lights or goes out accordingly.)

To cancel the effect on/off operation and return to

normal effect program selection, press Pedal

Switch B again. (The lamp goes out.)

NOTE ■

The effect on/off changes that you make here

are temporary. The original on/off settings are re-

stored as soon as you change programs. The on/off

switching of the MOD 1/2 and Delay/Reverb blocks is

determined by the On/Off parameter of those blocks.

(See pages 24 and 27.)

Press this to turn Distortion

block on or off. (The lamp

lights when the block is on.)

DIST / INSERT

DIST / INSER

OFF

Effect programs can be edited in the Edit mode. Once you’ve edited a program, you can save it

to a User memory location. (See SAVING EFFECT PROGRAMS on page 31.)

CAUTION! ■

Be careful not to press the

button at any time during editing. Doing so

will call up the original effect program’s settings and erase all settings you had made to that

point.

OPERATION

Select an effect program for editing and press the

e button to enable the Edit mode.

(The EDIT/COMPARE lamp lights and the ON/OFF

lamp above Pedal Switch B flashes.)

Use Pedal Switches 1 – 5 to turn on the desired

effect blocks.

HINT ■

Since you’ll probably want to listen to the

changes as you make them, make sure that all

relevant effect blocks are turned on. Better yet, turn off

all blocks except the one you are editing. This lets you

clearly hear only the effect you wish to edit. (One

possible exception to this guideline is the Amp Simula-

tor effect, changes to which are easier to hear when

Distortion is also on.)

Use the y and n buttons to select the

desired effect block row (in the parameter matrix

printed on the panel). (The lamp at the left of the

corresponding block lights.)

NOTE ■

The TUNER/METRONOME row cannot be

selected in the Edit mode.

Use the Parameter Dials to adjust the effect param-

eters.

Parameter Dial A is used to change the effect type of

the selected block; B – E are used to change the

corresponding parameters.

In the example shown below, the EQ/AMP block has

been selected.

•••••••••••••••••••••••••••••••••••••••••••••••••

ABCDE

COPY / SWAP / WRITE

MEMORY NO.

YES

•••••

••••••

•

••••••

••••••••••••••••••••••

PARAM

CHECK

•

COMP

DIST /

INSERT

EQ / AMP

DELAY

REVERB

N.GATE/UTIL

TUNER/

METRONOME

MOD 2

MOD 1

ATTACK

PRE-DRIVE*

LOW / —

TIME

THRESHOLD

SPEED

PITCH

PITCH L

ENHANCE

SENSE

DRIVE

MID / —

TONE

VOLUME POSITION

BEAT

(14~88 = 1/4~8/8)

DEPTH

— / PITCH R

FREQUENCY

—

TONE

HIGH / TONE

MIX

MINIMUM VOLUME

TEMPO

(60~86.=60~186)

TONE / FB

MIX

MIX / RANGE

LEVEL

TOTAL LEVEL

CLICK LEVEL

(1 LO 2 MID 3 HI)

ON/OFF

(SWITCH 4)

1 EQ / 2 STACK 3 COMBO 4 TUBE

————---

1~3

OD, DIST1,2 (DI*+AN)

4,5 OD*+DIST1,2

6~11 OD, DIST1,2+INSERT 12 INSERT

————---

TUNING PITCH

(0~5

440~445Hz)

1 CHORUS / 2 FLANGER 3 PHASER

4 PITCH SHIFT / 5 DETUNE

6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH

1 HALL 2 ROOM 3 STAGE 4 PLATE

ON/OFF

(SWITCH 5)

—

Use these to select

the desired block

for editing. (In this

example, EQ/AMP

is selected.)

Selects the type of

effect. (In this

example, 1 EQ is

selected.)

Adjusts the LOW parameter for the

EQ effect. (The dash indicates that

no parameter is available for the

other effects.)

Adjusts the MID parameter

for the EQ effect. (The dash

indicates that no parameter

is available for the other

effects.)

Adjusts the HIGH

parameter for the EQ effect

and the TONE parameter

for the others.

Adjusts

the LEVEL

parameter.

Pagina se încarcă ...

Yamaha GW33 Manualul proprietarului

Marca: Yamaha

Model: GW33

Categorie: Amplificator de instrumente muzicale

Tip: Manualul proprietarului

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha GW33 El kitabı
français: Yamaha GW33 Le manuel du propriétaire
čeština: Yamaha GW33 Návod k obsluze
русский: Yamaha GW33 Инструкция по применению
English: Yamaha GW33 Owner's manual
polski: Yamaha GW33 Instrukcja obsługi
Deutsch: Yamaha GW33 Bedienungsanleitung
italiano: Yamaha GW33 Manuale del proprietario
español: Yamaha GW33 El manual del propietario
svenska: Yamaha GW33 Bruksanvisning
dansk: Yamaha GW33 Brugervejledning
português: Yamaha GW33 Manual do proprietário
Nederlands: Yamaha GW33 de handleiding

Yamaha GW33 Manualul proprietarului

Yamaha GW33 Manualul proprietarului

în alte limbi

Lucrări conexe