Indesit XWE 71252 Manual de utilizare

Categorie
Mașini de spălat
Tip
Manual de utilizare

Acest manual este potrivit și pentru

1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9-10
Table of wash cycles
Wash options
Push & Wash
Detergents and laundry, 11-12
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13
Service, 14
English,1
GB
XWE 71252
BG
Български,29
HU
Magyar,43
RO
Română,57
GR
Ελληνικά,15
PL
Polski,71
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with the
installation process.
3 . R e m o v e t h e 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
p e r f e c t l y l e v e l ,
c o m p e n s a t e f o r
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2 . C o n n e c t t h e
i n l e t h o s e t o t h e
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand side
of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see
opposite);
the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
65 - 100 cm
Technical data
Model
XWE 71252
Dimensions
width 59.5 cm
height 85 cm
depth 54 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
and
1015/2010
Programme 8:
Cotton Standard 60°.
Programme 9:
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU
4
GB
Care and maintenance
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front
of the machine by
first pressing it in
the centre and then
pushing downwards
on both sides until
you can remove it
(see figures).
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it
and during all maintenance work.
Cleaning the washing machine
• The outer parts and rubber components
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
• The washing machine has a “Auto Clean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want
to use either the detergent (i.e. a quantity
10% the quantity specified for lightly-soiled
garments) or special additives to clean the
washing machine. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and
will last approximately 70 minutes. To stop the
cycle press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards
(2) (see figure).
Wash it under running
water; this procedure
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
2
1
1
2
3
A
B
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. remove the cover panel
on the lower front part of
the washing machine (see
figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
1
2
3
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button
and indicator light
DELAYED
START
button
OPTION
buttons
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
PUSH & WASH button: (see “Wash cycles and options”).
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of wash cycles”).
OPTION buttons: press to select the available options.
The indicator light corresponding to the selected option will
remain lit.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAYED START button: press to set a delayed
start for the selected wash cycle; the delay period appears
on the display.
START/PAUSE button and indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an amber colour. If the symbol is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 8 W
DISPLAY
PUSH & WASH
button
7
GB
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of
10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon
will then switch off approximately 1 minute after the final amount of time remaining has appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
There are three levels in section C concerning the washing options.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
Display
B
C
A
C
8
GB
Running a wash cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the
relevant compartments as described in “Detergents and
laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH & WASH” button to start the wash
programme.
Traditional programming
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described inDetergents and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 8 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
Press the button to enable the option; the indicator
light corresponding to the button will switch on.
Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will
flash accompanied by a buzzer (3 beeps), and only
the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Table of wash cycles
Wash options
Rapid
When this button is pressed the first time, the 9’ icon will
light up, when pressed the second time the 30’ icon lights
up and the third time the 1h icon lights up. When pressed
the fourth time the 9’ icon lights up again.
! It cannot be used in conjunction with wash cycles 1-2-3-
4-5-6-7-8-9-10-11-12-13- - .
Fast Forward
During a wash programme and under certain conditions,
pressing this button allows for ending the wash
programme after only 20’ if necessary, by performing a
brief rinse cycle followed by a spin cycle at maximum 800
rpm or lower, if reduced manually during the programme
customisation phase. In this case, washing and rinsing
performance will be reduced. After pressing the button, the
relative indicator light turns on together with the indicator
light of the rinse phase. If the selected temperature is
equal to 40° and/or the button is pressed during the initial
phase of the programme, the “Fast Forward” option lasts
longer so that the detergent can dissolve properly and
avoid damaging the fabrics. In this case, the rinse phase
indicator light flashes while the wash indicator light remains
fixed until the necessary activation conditions are fulfilled.
If less than 20’ remain of the wash programme, the option
will be disabled.
! It cannot be used in conjunction with wash cycles 2-4-5-
6-14- - .
Anti-Allergy
This option allows for selecting up to three additional rinse
cycles at the end of the wash cycle:
- pressing the button once activates the first level extra
rinse cycle, “Clean water”, which allows for performing an
extra rinse cycle after the wash cycle to guarantee optimal
performance.
- pressing the button twice sets the second rinse level,
“Dermo Protect”, which adds two extra rinse cycles and is
recommended for sensitive skin types.
- pressing the button the third time sets the “Anti-Allergy
function, which allows for adding three additional rinse cycles at
the end of the wash cycle, in order to fully eliminate detergent
residues and - if used together with a 6 cycle - the main
allergens too, such as pollen, mites and cat or dog hair.
The wash cycle duration varies according to the number of
selected rinse cycles.
! It cannot be used in conjunction with wash cycles 2-4-14- .
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.
3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle duration
Prewash
Wash
Fabric
softener
Bleach
Special
1
Sport
30° 600 -
- 3,5 - - - 55’
2
Dark
30° 800 -
- 4 - - - 70’
3
Anti-odour (Cotton) 60° 1000 -
- 3,5 - - - 110’
3
Anti-odour (Synthetic) 40° 1000 -
- 3,5 - - - 100’
4
Delicate
30° 0 -
- 1 - - - 80’
5
Wool: for wool, cashmere, etc. 40° 800 -
- 1,5 - - - 70’
6
Duvet: for down-stuffed garments. 30° 1000 -
- 2 - - - 110’
Standard
7
Cottons with Pre-wash: extremely soiled whites. 90° 1200
- 7 53 2,15 77 170’
8
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200 -
- 7 53 1,07 52,5 180’
9
Cotton Standard 40° (2): lightly soiled whites and delicate colours.
40° 1200 -
- 7 53 1,00 75 170’
10
Synthetic: heavily soiled resistant colours. 60° 800 -
- 3,5 46 0,79 46 110’
10
Synthetic (3): lightly soiled resistant colours. 40° 800 -
- 3,5 46 0,56 46 100’
11
Coloured
40° 1200 -
- 7 53 0,89 70 100’
Eco & Rapid
12
Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -
- 7 - - - 170’
13
Eco Synthetic
20° 800 -
- 7 - - - 120’
14
Rapid
- 800 - -
- 1,5 - - - 9’
14
Rapid
30° 800 -
- 3 80 0,22 34 30
14
Rapid
60° 1000 -
- 7 - - - 60’
Partials
Rinse/Bleach - 1200 - -
7 - - - 50’
Spin + Drain - 1200 - - - - 7 - - - 25’
10
GB
Push & Wash
This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF
button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the
Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.
The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 3,5 kg. (Cycle duration 50’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns
green and the door will lock (the DOOR LOCKED symbol turns on).
N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at
which it was interrupted.
4. Once the programme is finished, the END indicator light turns on.
11
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition
into slot B.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “max” level indicated
on the central pin.
Extra compartment 4: Bleach
Bleach cycle
Insert the additional compartment 4 (provided) into
compartment 1. In pouring the bleach do not exceed the
max” level indicated on the central pin.
Perform bleaching by pouring the bleach into additional
compartment 4 and set the programme .
! Traditional bleach should be used on resistant white
fabrics, and delicate bleach for coloured and synthetics
fabrics and for wool.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
Empty all garment pockets and check the buttons.
Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Special wash cycles
Sport (programme 1) is designed for washing lightly soiled
sports clothing (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated
in the “Table of wash cycles” We recommend using liquid
detergent, and adding the amount suitable for a half-load.
Dark: use programme 2 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
Anti-odour: use programme 3 for washing garments
with bad odours (e.g. smoke, sweat, fried food). The
programme is designed to remove bad odours while
preserving the fabric fibres. Synthetics fabrics or mixed
loads should be washed at 40°, and resistant cotton
fabrics at 60°.
Delicate: use programme 4 to wash very delicate
garments. It is advisable to turn the garments inside out
before washing them. For best results, use liquid detergent
on delicate garments.
Wool: the wool wash programme of this machine has
been tested and approved by The Woolmark Company
for the washing of wool containing garments labelled as
“hand wash” provided that the garments are washed
according to the instructions on the garment label and
those issued by the manufacturer of this washing machine.
(M1126)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Duvet: to wash single duvets (the weight of which should
not exceed 2 kg), cushions or clothes padded with
goose down such as puffa jackets, use the special wash
programme number 6. We recommend that duvets are
placed in the drum with their edges folded inwards (see
figure) and that no more than ¾ of the total volume of the
drum is used. To achieve the best results, we recommend
that a liquid detergent is used and placed inside the
detergent dispenser drawer.
Coloured: use this programme 11 to wash bright
coloured clothes. The programme is designed to maintain
bright colours over time.
1
2
3
4
A
B
12
GB
Cotton Standard 20° (programme 12) ideal for lightly
soiled cotton loads. The effective performance levels
achieved at cold temperatures, which are comparable to
washing at 40°, are guaranteed by a mechanical action
which operates at varying speed, with repeated and
frequent peaks.
Eco Synthetic (programme 13) ideal for mixed loads
(cotton and synthetics) with a normal soil level. The
effective performance levels achieved at cold temperatures
are guaranteed by a mechanical action which operates at
varying speed, across set average intervals.
Rapid (programme 14) allows for varying the garment
treatment duration from 9’ to 1h. Pressing the
corresponding “Rapid” button allows for varying the cycle
duration between 9’ (refresh), 30’ (wash), 1h (wash).
The 9’ cycle refreshes garments using fabric softener
only; it is advisable not to add any detergent into
the machine. The 30’ programme is designed to wash
lightly soiled garments at 30° (excluding wool and silk)
with a 3 kg maximum load in a short time: it only lasts 30
minutes and allows for saving time and energy. The “1h”
cycle is designed to wash moderately soiled resistant
cotton garments at 60° in an hour, with good washing
performance. For synthetic or mixed garments, we
recommend lowering the temperature down to 40°.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
13
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” on the
display).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
Theoption and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Push & Wash does not activate.
The programme lasts a lot less
that expected.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text “for
washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
After switching on the machine a control other than Push & Wash was activated.
Switch the machine off and press the Push & Wash button.
The “Fast Forward” option was activated.
14
GB
Service
Before contacting the Technical Assistance Service:
Check whether you can solve the problem alone (seeTroubleshooting”).
Restart the wash cycle to check whether the problem has been solved.
If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
15
GR
Ελληνικά
GR
ΠΛΥΝΤΗΡΙΟ
Περιεχόμενα
Εγκατάσταση, 16-17
Αποσυσκευασία και οριζοντίωση
Υδραυλικές και ηλεκτρικές συνδέσεις
Πρώτος κύκλος πλυσίματος
Τεχνικά στοιχεία
Συντήρηση και φροντίδα, 18
Αποκλεισμός νερού και ηλεκτρικού ρεύματος
Καθαρισμός του πλυντηρίου
Καθαρισμός του συρταριού απορρυπαντικών
Φροντίδα της πόρτας και του κάδου
Καθαρισμός της αντλίας
Έλεγχος του σωλήνα τροφοδοσίας του νερού
Προφυλάξεις και συμβουλές, 19
Γενική ασφάλεια
Διάθεση
Χειρονακτικό άνοιγμα της πόρτας
Περιγραφή του πλυντηρίου, 20-21
Ταμπλό ελέγχου
Οθόνη
Πως διενεργείται ένας κύκλος πλυσίματος, 22
Προγράμματα και δυνατότητες, 23-24
Πίνακας των Προγραμμάτων
Δυνατότητες πλυσίματος
Push & Wash
Απορρυπαντικά και μπουγάδα, 25-26
Θήκη απορρυπαντικών
Κύκλος λεύκανσης
Προετοιμασία της μπουγάδας
Ειδικά προγράμματα
Σύστημα ισοστάθμισης του φορτίου
Ανωμαλίες και λύσεις, 27
Υποστήριξη, 28
XWE 71252
Οδηγίες χρήσης
16
GR
Μια φροντισμένη οριζοντίωση προσδίδει
σταθερότητα στη μηχανή και αποσοβεί
δονήσεις, θορύβους και μετατοπίσεις κατά τη
λειτουργία. Σε περίπτωση μοκέτας ή τάπητα,
ρυθμίστε τα ποδαράκια έτσι ώστε να υφίσταται
κάτω από το πλυντήριο αρκετός χώρος για τον
αερισμό.
Υδραυλικές και ηλεκτρικές
συνδέσεις
Σύνδεση του σωλήνα τροφοδοσίας του
νερού
1 . Σ υ ν δ έ σ τ ε τ ο
σωλήνα τροφοδοσίας
βιδώνοντάς τον σε
ένα κρουνό κρύου
ν ε ρ ο ύ μ ε σ τ ό μ ι ο
σπειρώματος 3/4 gas
(βλέπε εικόνα).
Πρι ν τη σύν δεσ η,
αφήστε να τρέξει το
νερό μέχρι να γίνει
διαυγές.
2. Συνδέστε το σωλήνα
τ ρ ο φ ο δ ο σ ί α ς σ τ ο
πλυντήριο βιδώνοντάς
τον στην αντίστοιχη
είσοδο νερού, στο
πίσω μέρος επάνω
δεξιά (βλέπε εικόνα).
3. Προσέξτε ώστε στο σωλήνα να μην
υπάρχουν ούτε πτυχώσεις, ούτε στενώσεις.
! Η πίεση νερού του κρουνού πρέπει να
κυμαίνεται μεταξύ των τιμών του πίνακα Τεχνικά
στοιχεία (βλέπε σελίδα δίπλα).
! Αν το μήκος του σωλήνα τροφοδοσίας δεν
επαρκεί, απευθυνθείτε σε ένα ειδικευμένο
κατάστημα ή σε εξουσιοδοτημένο τεχνικό.
! Μη χρησιμοποιείτε ποτέ
χρησιμοποιημένους σωλήνες.
! Χρησιμοποιείτε εκείνους που σας παρέχονται
με τη μηχανή.
Εγκατάσταση
! Είναι σημαντικό να διατηρήσετε το εγχειρίδιο
αυτό για να μπορείτε να το συμβουλεύεστε
οποιαδήποτε στιγμή. Σε περίπτωση πώλησης,
παραχώρησης ή μετακόμισης, βεβαιωθείτε
ότι παραμένει μαζί με το πλυντήριο για να
πληροφορεί τον νέο ιδιοκτήτη για τη λειτουργία
και τις σχετικές προειδοποιήσεις.
! Διαβάστε προσεκτικά τις οδηγίες: υπάρχουν
σημαντικές πληροφορίες για την εγκατάσταση,
τη χρήση και την ασφάλεια.
Αποσυσκευασία και οριζοντίωση
Αποσυσκευασία
1. Αποσυσκευάστε το πλυντήριο.
2. Ελέγξτε αν το πλυντήριο έχει υποστεί ζημιές
κατά τη μεταφορά. Αν έχει υποστεί ζημιές
μην το συνδέετε και επικοινωνήστε με τον
μεταπωλητή.
3. Αφαιρέστε τις 4
βίδες προστασίας
για τη μεταφορά και
το λαστιχάκι με το
σχετικό διαχωριστικό,
που βρίσκονται στο
πίσω μέρος (βλέπε
εικόνα).
4. Κλείστε τις οπές με τα πλαστικά πώματα
που σας παρέχονται.
5. Διατηρείστε και τα τρία τεμάχια: αν το
πλυντήριο χρειαστεί να μεταφερθεί, θα πρέπει
να ξαναμονταριστούν.
! Οι συσκευασίες δεν είναι παιχνίδια για
μικρά παιδιά.
Ευθυγράμμιση
1. Εγκαταστήστε το πλυντήριο σε ένα
δάπεδο επίπεδο και ανθεκτικό, χωρίς να το
ακουμπήσετε σε τοίχους, έπιπλα ή άλλο.
2. Αν το δάπεδο
δεν είναι απόλυτα
οριζοντιωμένο,
αντισταθμίστε
τις ανωμαλίες
βιδώνοντας ή
ξεβιδώνοντας τα
πρόσθια ποδαράκια
(βλέπε εικόνα).Η
γωνία κλίσης,
μετρημένη στην
επιφάνεια εργασίας, δεν πρέπει να ξεπερνάει
τις 2°.
17
GR
Σύνδεση του σωλήνα αδειάσματος
Συνδέστε το σωλήνα
αδειάσματος, χωρίς
να τον διπλώσετε,
σε μια σωλήνωση
αδειάσματος ή σε
μ ι α πα ρ οχ έ τ ε υ σ η
επιτοίχια σε ύψος από
το έδαφος μεταξύ 65
και 100 cm.
Ή στηρίξτε τον στο
χείλος ενός νιπτήρα
ή μ ι α ς λ ε κ ά ν η ς ,
δένοντας τον οδηγό
που σας παρέχεται
στον κρουνό (βλέπε
εικόνα). Το ελεύθερο
άκρο του σωλήνα
α δ ε ι ά σ μ α τ ο ς δ ε ν
πρέπει να παραμένει
βυθισμένο στο νερό.
! Δεν συνιστάται η χρήση προεκτάσεων
σωλήνων. Αν απαιτείται, η προέκταση πρέπει
να έχει την ίδια διάμετρο του αρχικού σωλήνα
και να μην ξεπερνάει τα 150 cm.
Ηλεκτρική σύνδεση
Πριν εισάγετε το βύσμα στην ηλεκτρική
πρίζα, βεβαιωθείτε ότι:
η πρίζα διαθέτει γείωση και τηρεί τις εκ του
νόμου προδιαγραφές.
Η πρίζα να είναι σε θέση να υποφέρει το μέγιστο
φορτίο ισχύος της μηχανής, που αναφέρεται
στον πίνακα Τεχνικών στοιχείων (βλέπε δίπλα).
Η τάση τροφοδοσίας να κυμαίνεται μεταξύ
των τιμών που αναφέρονται στον πίνακα
Τεχνικών στοιχείων (βλέπε δίπλα).
Η πρίζα να είναι συμβατή με το βύσμα
του πλυντηρίου. Σε αντίθετη περίπτωση,
αντικαταστήστε την πρίζα ή το βύσμα.
! Το πλυντήριο δεν εγκαθίσταται σε ανοιχτό
χώρο, ακόμη και αν ο χώρος είναι καλυμμένος,
διότι είναι πολύ επικίνδυνο να το αφήνετε
εκτεθειμένο σε βροχή και κακοκαιρία.
! Με την εγκατάσταση του πλυντηρίου, η πρίζα
ρεύματος πρέπει να είναι εύκολα προσβάσιμη.
! Μη χρησιμοποιείτε προεκτάσεις και
πολύπριζα.
! Το καλώδιο δεν πρέπει να φέρει πτυχές ή
να είναι συμπιεσμένο.
65 - 100 cm
! Το καλώδιο τροφοδοσίας πρέπει να
αντικαθίσταται μόνο από εξουσιοδοτημένους
τεχνικούς.
Προσοχή! Η επιχείρηση αποποιείται κάθε
ευθύνης σε περίπτωση που δεν τηρούνται
αυτοί οι κανόνες.
Πρώτος κύκλος πλυσίματος
Μετά την εγκατάσταση, πριν τη χρήση,
διενεργήστε ένα κύκλο πλυσίματος με
απορρυπαντικό και χωρίς ρούχα θέτοντας το
πρόγραμμα “ΑΥΤΌ-ΚΑΘΑΡΙΣΜΟΣ” (βλέπε
«Καθαρισμός του πλυντηρίου»).
Ôå÷íéêÜ óôïé÷åßá
ÌïíôÝëï XWE 71252
ÄéáóôÜóåéò
ðëÜôïò cm 59,5
ýøïò cm 85
âÜèïò cm 54
×ùñçôéêüôçôá áðü 1 Ýùò 7 kg
ÇëåêôñéêÝò
óõíäÝóåéò
ÂëÝðå ôçí ðéíáêßäá
÷áñáêôçñéóôéêþí åðß ôçò
ìç÷áíÞò
ÓõíäÝóåéò
íåñïý
ìÝãéóôç ðßåóç
1 MPa (10 bar)
ÅëÜ÷éóôç ðßåóç
0,05 MPa (0,5 bar)
÷ùñçôéêüôçôá ôïõ êÜäïõ 52
ëßôñá
Ôá÷ýôçôá
óôõøßìáôïò
ìÝ÷ñé 1200 óôñïöÝò ôï ëåðôü
Προγράμματα
ελέγχου
σύμφωνα με
τις οδηγίες
1061/2010
και
1015/2010
ðñüãñáììá 8; κανονικό
πρόγραμμα για βαμβακερά
στους 60°C.
ðñüãñáììá 9; κανονικό
πρόγραμμα για βαμβακερά
στους 40°C.
Ç óõóêåõÞ áõôÞ åßíáé
óýìöùíç ìå ôéò áêüëïõèåò
ÊïéíïôéêÝò Ïäçãßåò:
- 2004/108/CE
(ÇëåêôñïìáãíçôéêÞ
Óõìâáôüôçôá)
- 2012/19/EU
- 2006/95/CE (×áìçëÞ ÔÜóç)
θόρυβος
(dB(A) re
1 pW)
Πλύσιμο: 59
Στύψιμο: 80
18
GR
Φροντίδα της πόρτας και του κάδου
Να αφήνετε πάντα μισόκλειστη την πόρτα
για να μην παράγονται δυσοσμίες.
Καθαρισμός της αντλίας
Το πλυντήριο διαθέτει μια αντλία
αυτοκαθαριζόμενη που δεν χρειάζεται
συντήρηση. Μπορεί, όμως, να τύχει να
πέσουν μικρά αντικείμενα (κέρματα, κουμπιά)
στον προθάλαμο που προστατεύει την
αντλία, που βρίσκεται στο κάτω μέρος αυτής.
! Βεβαιωθείτε ότι ο κύκλος πλυσίματος έχει
τελειώσει και βγάλτε το βύσμα.
Για να έχετε πρόσβαση στον προθάλαμο:
1. αφαιρέστε το
πάνελ κάλυψης στο
πρόσθιο πλευρό
της μηχανής προς
το κέντρο, κατόπιν
ωθήστε προς τα
κάτω αμφότερα τα
πλευρά και βγάλτε το
(βλέπε εικόνες).
2. Ξεβιδώστε το
καπάκι στρέφοντάς
το αριστερόστροφα
(βλέπε εικόνα): είναι
φυσικό να βγαίνει
λίγο νερό.
3. καθαρίστε επιμελώς το εσωτερικό
4. ξαναβιδώστε το καπάκι
5. ξαναμοντάρετε το πάνελ όντας σίγουροι,
πριν το σπρώξετε προς τη μηχανή, ότι έχετε
εισάγει τα γαντζάκια στις αντίστοιχες εσοχές.
Έλεγχος του σωλήνα τροφοδοσίας
του νερού
Ελέγχετε το σωλήνα τροφοδοσίας
τουλάχιστον μια φορά ετησίως. Αν
παρουσιάζει σκασίματα και σχισμές
αντικαθίσταται: κατά τα πλυσίματα οι ισχυρές
πιέσεις θα μπορούσαν να προκαλέσουν
αναπάντεχα σπασίματα.
! Μη χρησιμοποιείτε ποτέ
χρησιμοποιημένους σωλήνες.
Συντήρηση και φροντίδα
Αποκλεισμός νερού και ηλεκτρικού
ρεύματος
Κλείνετε τον κρουνό του νερού μετά
από κάθε πλύσιμο. Έτσι περιορίζεται η
φθορά της υδραυλικής εγκατάστασης του
πλυντηρίου και αποσοβείται ο κίνδυνος
απωλειών.
Να βγάζετε το βύσμα από το ρεύμα όταν
καθαρίζετε το μηχάνημα και κατά τις
εργασίες συντήρησης.
Καθαρισμός του πλυντηρίου
• Το εξωτερικό μέρος και τα λαστιχένια
μέρη μπορούν να καθαρίζονται με ένα πανί
βρεγμένο με χλιαρό νερό και σαπούνι. Μη
χρησιμοποιείτε διαλύτες ή αποξυστικά.
• Το πλυντήριο διαθέτει ένα πρόγραμμα
“ΑΥΤΌ-ΚΑΘΑΡΙΣΜΟΣ” των εσωτερικών
μερών που πρέπει να διενεργείται χωρίς
κανένα τύπο φορτίου στον κάδο.
Το απορρυπαντικό (σε ποσότητα ίση με
το 10% της προτεινόμενης για ρούχα
λίγο λερωμένα) ή πρόσθετα ειδικά για
τον καθαρισμό του πλυντηρίου, μπορούν
να χρησιμοποιηθούν ως ενισχυτικά
στο πρόγραμμα πλύσης. Συνιστάται να
διενεργείτε το πρόγραμμα καθαρισμού κάθε
40 κύκλους πλυσίματος.
Για την ενεργοποίηση του προγράμματος
πατήστε το κουμπί Α για 5 sec (βλέπε
Εικόνα). Το πρόγραμμα θα ξεκινήσει
αυτόματα και θα έχει διάρκεια περίπου
70 λεπτών. Για να σταματήσετε τον κύκλο
πατήστε το κουμπί START/PAUSE.
Καθαρισμός του συρταριού
απορρυπαντικών
Για να βγάλετε το
συρτάρι πατήστε το
μοχλό (1) και τραβήξτε
το προς τα έξω (2)
(βλέπε εικόνα).
Πλένετέ το κάτω από
τρεχούμενο νερό. Ο
καθαρισμός αυτός
διενεργείται συχνά.
2
1
A
B
1
2
3
19
GR
Προφυλάξεις και συμβουλές
! Το πλυντήριο σχεδιάστηκε και κατασκευάστηκε σύμφωνα με
τους διεθνείς κανόνες ασφαλείας. Αυτές οι προειδοποιήσεις
παρέχονται για λόγους ασφαλείας και πρέπει να διαβάζονται
προσεκτικά.
Γενική ασφάλεια
Η συσκευή αυτή σχεδιάστηκε αποκλειστικά για οικιακή
χρήση.
Η συσκευή αυτή μπορεί να χρησιμοποιηθεί
από παιδιά άνω των 8 ετών και από άτομα με
μειωμένες φυσικές, αισθητηριακές ή νοητικές
ικανότητες ή με εμπειρία και γνώσεις ανεπαρκείς,
αν επιτηρούνται ή αν έχουν δεχτεί κατάλληλη
εκπαίδευση σχετικά με τη χρήση της συσκευής με
τρόπο ασφαλή και κατανοώντας τους σχετικούς
κινδύνους. Τα παιδιά δεν πρέπει να παίζουν με τη
συσκευή. Συντήρηση και καθαρισμός δεν πρέπει
να διενεργούνται από παιδιά χωρίς επιτήρηση.
Το πλυντήριο πρέπει να χρησιμοποιείται μόνο από
ενήλικα άτομα και σύμφωνα με τις οδηγίες που
αναφέρονται στο παρόν εγχειρίδιο.
Μην αγγίζετε το μηχάνημα με γυμνά πόδια ή με τα χέρια
ή τα πόδια βρεγμένα.
Μην βγάζετε το βύσμα από την ηλεκτρική πρίζα
τραβώντας το καλώδιο, αλλά να πιάνετε την πρίζα.
Μην ανοίγετε το συρταράκι απορρυπαντικών ενώ το
μηχάνημα είναι σε λειτουργία.
Μην αγγίζετε το νερό αδειάσματος, αφού μπορεί να
φτάσει σε υψηλές θερμοκρασίες.
Μην ζορίζετε σε καμία περίπτωση την πόρτα: θα
μπορούσε να χαλάσει ο μηχανισμός ασφαλείας που
προστατεύει από τυχαία ανοίγματα.
Σε περίπτωση βλάβης, σε καμία περίπτωση να
μην επεμβαίνετε στους εσωτερικούς μηχανισμούς
προσπαθώντας να την επισκευάσετε.
Να ελέγχετε πάντα τα παιδιά να μην πλησιάζουν στο
μηχάνημα σε λειτουργία.
Κατά το πλύσιμο η πόρτα τείνει να θερμαίνεται.
Αν πρέπει να μετατοπιστεί, συνεργαστείτε δύο ή τρία
άτομα με τη μέγιστη προσοχή. Ποτέ μόνοι σας γιατί το
μηχάνημα είναι πολύ βαρύ.
Πριν εισάγετε τη μπουγάδα ελέγξτε αν ο κάδος είναι
άδειος.
Διάθεση
Διάθεση του υλικού συσκευασίας:
τηρείτε τους τοπικούς κανονισμούς, ώστε οι συσκευασίες
να μπορούν να επαναχρησιμοποιηθούν.
Η Ευρωπαϊκή Οδηγία 2012/19/CE για τα απορρίμματα
ηλεκτρικών και ηλεκτρονικών συσκευών, προβλέπει ότι
οι οικιακές ηλεκτρικές συσκευές δεν πρέπει να διατίθενται
στην κανονική ροή των στερεών αστικών απορριμμάτων.
Οι απορριπτόμενες συσκευές πρέπει να συλλέγονται
χωριστά για να βελτιστοποιείται το ποσοστό ανάκτησης
και ανακύκλωσης των υλικών που τις αποτελούν και
να αποφεύγονται δυνητικές ζημιές για την υγεία και το
περιβάλλον. Το σύμβολο του διαγραμμένου καλαθιού
υπάρχει σε όλα τα προϊόντα για να θυμίζει τις υποχρεώσεις
χωριστής συλλογής.
Για περιατέρω πληροφορίες, για τη σωστή απομάκρυνση
των οικιακών ηλεκτρικών συσκευών, οι κάτοχοι θα μπορούν
να απευθύνονταιi στην αρμόδια δημόσια υπηρεσία ή στους
μεταπωλητές.
Χειρονακτικό άνοιγμα της πόρτας
Στην περίπτωση αδυναμίας ανοίγματος της πόρτας εξ
αιτίας απουσίας ηλεκτρικής ενέργειας ενώ θέλετε να
απλώσετε την μπουγάδα, προχωρήστε ως ακολούθως:
1. βγάλτε το βύσμα από την
ηλεκτρική πρίζα.
2. βεβαιωθείτε ότι η στάθμη
του νερού στο εσωτερικό της
μηχανής είναι χαμηλότερη
σε σχέση με το άνοιγμα της
πόρτας. Σε αντίθετη περίπτωση
αφαιρέστε το σε περίσσεια νερό
μέσω του σωλήνα αδειάσματος
συλλέγοντάς το σε ένα κουβά
όπως φαίνεται στηνεικόνα.
3. αφαιρέστε το ταμπλό
κάλυψης στο πρόσθιο
πλευρό του πλυντηρίου
(βλέπε εικόνα).
4. χρησιμοποιώντας τη γλωσσίτσα που φαίνεται στην
εικόνα τραβήξτε προς τα έξω μέχρι να ελευθερώσετε το
πλαστικό από το στοπ. Τραβήξτε το ακολούθως προς τα
κάτω και ταυτόχρονα ανοίξτε την πόρτα.
5. ξαναμοντάρετε το πάνελ όντας σίγουροι, πριν το
σπρώξετε προς τη μηχανή, ότι έχετε εισάγει τα γαντζάκια
στις αντίστοιχες εσοχές.
1
2
3
20
20
GR
Περιγραφή του πλυντηρίου
Πίνακας ελέγχου
Κουμπί
ΘΕΡΜΟΚΡΑΣΙΑΣ
ΕΠΙΛΟΓΈΑΣ
ΠΡΟΓΡΑΜΜΆΤΩΝ
Θήκη απορρυπαντικών
Κουμπί ON/OFF
Κουμπί
ΣΤΥΨΙΜΑΤΟΣ
Κουμπί και ενδεικτικό
φωτάκι START/PAUSE
ΟΘΌΝΗ
Κουμπί
ΚΑΘΥΣΤΕΡΗΜΕΝΗΣ
ΕΚΚΙΝΗΣΗΣ
Κουμπιά
ΛΕΙΤΟΥΡΓΙΑΣ
Θήκη απορρυπαντικών: για την προσθήκη
απορρυπαντικών και πρόσθετων (βλέπε
«Απορρυπαντικά και μπουγάδα»).
Κουμπί ON/OFF : πιέστε για λίγο το κουμπί για να
ανάψετε ή να σβήσετε τη μηχανή. Το ενδεικτικό φωτάκι
START/PAUSE πράσινου χρώματος που αναβοσβήνει
αργά δείχνει ότι η μηχανή είναι αναμμένη. Για να
σβήσετε το πλυντήριο κατά το πλύσιμο πρέπει να
κρατάτε πατημένο το κουμπί πιο πολύ, περίπου 3 sec.
Στιγμιαίο ή τυχαίο πάτημα δεν επιτρέπει το σβήσιμο της
μηχανής. Το σβήσιμο της μηχανής κατά το πλύσιμο σε
εξέλιξη ακυρώνει το ίδιο το πλύσιμο.
Κουμπί PUSH & WASH: (βλέπε «Προγράμματα και
δυνατότητες»).
ΕΠΙΛΟΓΕΑΣ ΠΡΟΓΡΑΜΜΑΤΩΝ: Για να θέσετε
το επιθυμητό πρόγραμμα (βλέπε τον “Πίνακα
προγραμμάτων”).
Κουμπιά ΔΥΝΑΤΟΤΗΤΑΣ: για να επιλέξετε τις διαθέσιμες
δυνατότητες. Το ενδεικτικό φωτάκι το σχετικό με
τηδυνατότητα που επελέγη θα παραμείνει αναμμένο.
Κουμπί ΘΕΡΜΟΚΡΑΣΙΑΣ : Πιέστε για να μειώσετε ή
να αποκλείσετε τελείως τη θερμοκρασία. Η τιμή φαίνεται
στην οθόνη.
Κουμπί ΣΤΥΨΙΜΑΤΟΣ : πιέστε για να μειώσετε ή να
αποκλείσετε τελείως το στύψιμο. Η τιμή φαίνεται στην
οθόνη.
Κουμπί ΕΚΚΙΝΗΣΗΣ ΜΕ ΥΣΤΕΡΗΣΗ : πατήστε για
να θέσετε μια εκκίνηση με υστέρηση του προεπιλεγμένου
προγράμματος. Η καθυστέρηση υποδεικνύεται στην
οθόνη.
Κουμπί και ενδεικτικό φωτάκι START/PAUSE : όταν
το πράσινου ενδεικτικό φωτάκι αναβοσβήνει αργά,
πατήστε το κουμπί για την εκκίνηση πλυσίματος. Με την
εκκίνηση του κύκλου το ενδεικτικό φωτάκι σταθεροποιείται.
Για να θέσετε μια παύση στο πλύσιμο, πατήστε εκ νέου
το κουμπί. Το ενδεικτικό φωτάκι θα αναβοσβήνει με
κεχριμπαρί χρώμα. Αν το σύμβολο δεν φωτίζεται,
μπορείτε να ανοίξετε την πόρτα. Για να ξεκινήσει πάλι το
πλύσιμο από το σημείο διακοπής, πατήστε εκ νέου το
κουμπί.
Τρόπος stand by
Το πλυντήριο αυτό, σύμφωνα με τις νέες διατάξεις για
την εξοικονόμηση ενέργειας, διαθέτει ένα σύστημα
αυτόματου σβησίματος (stand by) που τίθεται σε
λειτουργία εντός 30 λεπτών στην περίπτωση μη χρήσης.
Πιέστε στιγμιαία το κουμπί ON/OFF και περιμένετε να
ενεργοποιηθεί εκ νέου η μηχανή.
Κατανάλωση σε off-mode: 0,5 W
Κατανάλωση σε Left-on: 8 W
Κουμπί
PUSH & WASH
1 / 1

Indesit XWE 71252 Manual de utilizare

Categorie
Mașini de spălat
Tip
Manual de utilizare
Acest manual este potrivit și pentru

în alte limbi