Candy CHW74WX 75cm Gas Hob Manual de utilizare

Marca: Candy

Model: CHW74WX 75cm Gas Hob

Categorie: Plite

Tip: Manual de utilizare

Acest manual este potrivit și pentru

HOBS

USER INSTRUCTIONS

VARNÉ DESKY

NÁVOD POUŽITĺ

TABLES DE CUISSON

NOTICE D’EMPLOI

UND BEDIENUNGSANLEITUNG

INSTALLATIONS

ENCIMERAS

INSTRUCCIONES DE USO

INSTRUKCJE

UŻYCIA I MONTAŻU

ANKASTRE OCAK

KULLANIM KLAVUZU

NAVODILA ZA UPORABO

VGRADNJO IN PRIKLJU ITEVČ

ВАРОЧНЫЕ ПОВЕРХНОСТИ

ИНСТРУКЦИЯ ПОЛЬЗОВАТЕЛЯ

PIANI COTTURA

ISTRUZIONI PER L’USO

PLACAS

INSTRUÇ ES DE UTILIZAÇ OÕÃ

TŰZHELYLAPOK

HASZNÁLATI UTASÍTÁS

PLITE

MANUAL DE UTILIZARE

KOOKPLAATS

MANUAL DE UTILIZARE

• CHG6L

• CHW6L

CANDY HOOVER GROUP S.R.L. • Via Comolli 16 • 20861 Brugherio (MB) Italy

02 GB

SAFETY INSTURUCTIONS

We recommend you keep the instructions for

installation and use for later reference, and before

installing the hob, note its serial number in case

you need to get help from the after sales service.

WARNING: the appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements. Children under

8 years of age must be kept away from the

appliance unless they are continuously

supervised.

WARNING: use only hob guards designed by the

Manufacturer of the cooking appliance or

indicated by the Manufacturer of the appliance in

the instructions for use as suitable or hob guards

incorporated in the appliance. The use of

inappropriate guards can cause accidents.

WARNING: unattended cooking on a hob with fat

or oil can be dangerous and may result in fire.

NEVER try to extinguish a fire with water, but

switch off the appliance and then cover flame e.g.

with a lid or a fire blanket.

WARNING: danger of fire: do not store items on

the cooking surfaces.

WARNING: if the surface is cracked, do not touch

the glass and switch off the appliance to avoid the

possibility of electric shock.

This appliance can be used by children aged from

8 years and above and people with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Children should be supervised

to ensure that they do not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

CAUTION: the cooking process must be

supervised. A short term cooking process has to

be supervised continuously.

It is strongly recommended to keep children away

from the cooking zones while they are in operation

or when they are switched off, so long as the

residual heat indicator is on, in order to prevent

the risks of serious burns.

This appliance is not intended to be operated by

means of an external timer or separate remote

control system.

If present do not to stare into halogen lamp hob

elements.

Connect a plug to the supply cable that is able to

bear the voltage, current and load indicated on the

tag and having the earth contact. The socket must

be suitable for the load indicated on the tag and

must be having the earth contact connected and

in operation. The earth conductor is yellow-green

in color. This operation should be carried out by a

suitably qualified professional. In case of

incompatibility between the socket and the

appliance plug, ask a qualified electrician to

substitute the socket with another suitable type.

The plug and the socket must be conformed to

the current norms of the installation country.

Connection to the power source can also be

made by placing an omnipolar breaker between

the appliance and the power source that can bear

the maximum connected load and that is in line

with current legislation.

The yellow-green earth cable should not be

interrupted by the breaker. The socket or

omnipolar breaker used for the connection

should be easily accessible when the appliance is

installed.

The disconnection may be achieved by having

the plug accessible or by incorporating a switch in

the fixed wiring in accordance with the wiring

rules.

If the supply cord is damaged, it must be replaced

by Manufacturer, its service agent or similarly

qualified people in order to avoid a hazard. The

earth conductor (yellow-green) must be longer

than 10 mm on the terminal block side. The

internal conductors section should be

appropriate to the power absorbed by the hob

(indicated on the tag). The type of power cable

must be HO5V2V2-F.

Do not put metallic objects such as knives, forks,

spoons or lids on the hob. They could heat up.

Aluminum foil and plastic pans must not be

placed on heating zones.

After every use, some cleaning of the hob is

necessary to prevent the build-up of dirt and

grease. If left, this is recooked when the hob is

used and burns giving off smoke and unpleasant

smells, not to mention the risks of fire

propagation.

Never use a steam or high pressure spray to

clean the appliance.

Do not touch the heat zones during operation or

for a while after use.

Never cook food directly on the glass ceramic

hob.

Always use the appropriate cookware.Always

place the pan in the center of the unit that you are

cooking on.

Do not place anything on control panel.

Do not use the hob as a working surface.

Do not use the surface as a cutting board.

Do not store heavy items above the hob. If they

drop onto the hob, they may cause damage.

Do not use the hob for storage of any items.

Do not slide cookware across the hob.

03 GB

The hob may be installed in any worktop which is heat resistant to a

temperature of 100°C, and has a thickness of 25-45 mm. The

dimensions of the insert to be cut out of the worktop are in shown in

Figure 2.

When there is an accessible space between the built-in hob and the

cavity below, a dividing wall made of insulating material should be

inserted (wood or a similar material) (Figure 3).

If the Hob is fitted next to a cabinet on either side, the distance between

the Hob and the cabinet must be at least 15 cm ; while(see Figure 4)

the distance between the hob and the rear wall must be at least .70 mm

The distance between the hob and any other unit or appliance above it

(e.g.An extractor hood) must be no less than 70 cm .(Figure 4)

Metal objects in the drawer may reach high temperatures due to

air recirculation. It is therefore recommended to use an

intermediate wood panel.

Important - The diagram in figure 1 shows how the sealant should

be applied.

The Hob unit is fitted by attaching the Fixing Clamps supplied, using

the holes at the base of the unit.

If a hob of 60 cm is fitted above an oven which is not equipped with fan

cooling system it is recommended that openings are created within the

built in furniture to ensure correct air circulation.

The size of these openings must be at least 300 cm2 and placed as

shown in Figure 5.

1.1 BUILDING IN

1.2. SUITABLE LOCATION

This appliance must be installed in accordance with the regulations in

force and only used in a well ventilated space. Read the instructions

before installing or using this appliance.

A gas-powered cooking appliance produces heat and humidity in the

area in which it is installed. For this reason you should ensure good

ventilation either by keeping all natural air passages open or by

installing an extractor hood with an exhaust flue. Intensive and

prolonged use of the appliance may require extra ventilation, such as

the opening of a window or an increase in speed of the electric fan, if

you have one.

If a hood can not be installed, an electric fan should be fitted to an

outside wall or window to ensure that there isadequateventilation.

The electric fan should be able to carry out a complete change of air in

the kitchen 3-5 times every hour. The installer should follow the

relevant national standards.

2. ELECTRICAL CONNECTION (FOR U.K. ONLY)

Warning - this appliance must be earthed

This appliance is designed for domestic use only. Connection to the main

supply must be made by a competant electrician, ensuring that all current

regulations concerning such installations are observed.

The appliance must only be connected to a suitably rated spur point, a

3 pin 13 amp plug/socket is not suitable.A double pole switch must be

provided and the circuit must have appropriate fuse protection.

Further details of the power requirement of the individual product will

be found in the users’ instruction and on the appliance rating plate. In

the case of built-in product you are advised, should you wish to use a

longer cable than the one supplied, that a suitably rated heat resistant

type must be used.

The wiring must be connected to the mains supplyasfollows:

CONNECT TO SPUR TERMINAL

Green &Yellow Wire Earth Connection

Blue Wire Neutral Connection

Brown Wire Live Connection

Note: We do not advocate the use of earth leakage devices with

electric cooking appliances installed to spur points because of the

«nuisance tripping» which may occur. You are again reminded that the

appliance must be correctly earthed, the manufacturer declines any

responsibility for any event occurring as a result of incorrect electrical

installation.

2.1. ELECTRICAL CONNECTION

Check the data on the rating plate, located on the outside of the unit, to

ensure that the supply and input voltage are suitable.

Before connection, check the earthing system.

By Law, this appliance must be earthed. If this regulation is not complied

with, the Manufacturer will not be responsible for any damage caused to

persons or property. If a plug is not already attached, fit a plug

appropriate to the load indicated on the rating plate. The earth wire is

coloured yellow/green. The plug should always be accessible.

Where the Hob is connected direct to the electricity supply, a circuit

breaker must be fitted.

If the power supply cord is damaged this is to be replaced by a qualified

engineer so as to prevent any potential risk.

The earth wire ( green and yellow coloured ) must be at least 10 mm

longer than the live and neutral wires.

The section of the cable used must be of the correct size in relation to

the absorbed power of the hob.

Please check rating plate for the power details and ensure that the

power supply cord is of the type 3x0.75 mm² H05 V2V2-F.

LIVE

EARTH

NEUTRAL

Power Cable

Brown Wire

Green/Yellow Wire

Blue Wire

Mains Supply

If an appliance is not fitted with a supply cord and a plug, or with other

means for disconnection from the supply mains having a contact

separation in all poles that provide full disconnection under overvoltage

category III conditions, the instructions shall state that means for

disconnection must be incorporated in the fixed wiring in accordance with

the wiring rules.

1. INSTRUCTIONS FOR THE INSTALLER

INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION WHICH IF NOT CARRIED OUT CORRECTLY, CAN SERIOUSLY

AFFECT CONSUMER SAFETY. IT IS FOR THIS REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED

PERSON WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE. IN THE EVENT THAT THIS ADVICE IS

IGNOREDAND THE INSTALLATION IS CARRIED OUT BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALLRESPONSIBILITY

FORANY TECHNICALFAILURE OF THE PRODUCT WHETHER OR NOT IT RESULTS IN DAMAGE TO GOODS OR INJURYTO INDIVIDUALS.

These instructions are for qualified personnel, installation of

equipment must be in line with the relevant national standard. (For

U.K. only: by law the gas installation\commissioning must be

carried out by a "Gas Safe" installer)

All work must be carried out with the electricitysupplydisconnected.

The rating plate on the hob shows the type of gas with which it is

designed to be used. Connection to the mains gas supply or gas

cylinder should be carried out after having checked that it is regulated

for the type of gas with which it will be supplied. If it is not correctly

regulated see the instructions in the following paragraphs to change

gas setting.

For liquid gas (cylinder gas) use pressure regulators which comply

with the relevant national standards.

Use only pipes,washers and sealing washers which comply with the

relevant national standards.

For some models a conic link is furnished to outfit for the installation in

the countries where this type of link is obligatory; in picture 8 it is

pointed out how to recognize the different types of links (CY =

cylindrical, CO = conic). In every case the cylindrical part of the link

has to be connected to the hob.

When connecting the hob to the gas supply via use offlexible hoses

please ensure that the maximum distance covered by the hose does

not exceed 2 metres.

The flexible tube shall be fitted in such a way that it cannot come into

contact with a moveable part of the housing unit (e.g. a drawer) and does

not pass through any space where it may become crushed/ kinked or

damaged in any way.

To prevent any potential damage to the hob please carry out the

installation following this sequence (picture 6):

1)As illustrated, assemble parts in sequence:

A: 1/2 MaleAdaptor Cylindirical

B: 1/2 Seal

C: 1/2 Female GasAdaptor Conical-Cylindirical or

Cylindirical-Cylindirical

2.2. GAS CONNECTION

Table A

Burner Type

Ø pan/pot

(cm)

AUX

10 - 18

12 - 22

16 - 26

Auxiliary

Semi Rapid

Rapid

Power

(kW)

1,00

1,75

2,70

G20/20 mbar

(methane)

95 l/h

167 l/h

257 l/h

G30/28-30 mbar

(LPG)

73 g/h

127 g/h

196 g/h

04 GB

2.3. ADAPTING THE HOB TO DIFFERENT

TYPES OF GAS

To adapt the Hob for use with different types of gas, carry out the

following instructions:

•Remove the grids and burners

•Insert on hexagonal spanner (7 mm) into the burner support (Figure

•Unscrew the injector and replace it with one suitable for the gas to be

used (see gas type table)

2.4. REGULATING THE MINIMUM FLAME

After lighting the burners, turn the control knob to the minimum setting

and then remove the knob (this can easily be removed by applying

gentle pressure).

Using a small «Terminal» type screwdriver the regulating screw can

be adjusted as in Turning the screw clockwise reduces theFigure 9.

gas flow, whilst turning it anticlockwise increases the flow – Use this

adjustment to obtain a flame of approximately 3 to 4 mm in length and

then replace the control knob.

When the gas supply available is LPG - the screw to set the idle flame

must be turned (clockwise) to the end stop.

When you have carried out the new gas regulation, replace the old gas

rating plate on your appliance with one (supplied with hob) suitable for

the type of gas for which it has beenregulated.

3. USE OF HOB - USER INSTRUCTIONS

This appliance must only be used for the purpose for which it is

intended, domestic cooking, and any other use will be considered

improper and could therefore be dangerous. The Manufacturer will

not be responsible for any damage or loss resulting from improper

use.

3.1. USING THE GAS BURNER

To ignite the burners, place a lighted taper close to the burner, press in

and turn the control knob anti-clockwise.

If the burners have not been used for a couple of days, wait for a few

seconds before lighting the burner, this will allow any air present in the

pipes to escape.

For appliances fitted with electronic ignition carry out the following:

• Push in and turn the knob anticlockwise totheignitionsymbol.

• İgnite the burner by pressing the sparker button.

For hobs fitted with automatic ignition simply push in and turn the knob

to the ignition symbol.

The ignition system will continue to generate sparks as long as the

control knob is being pressed.

If the burner has not ignited within 5 seconds, turn the knob to the 0

position and repeat the operation.

For models fitted with a safety tap (which cuts-off the flow of gas if the

flame is accidentally extinguished) the burners are ignited and

described above, but care must be taken.

Prior to switching on the gas hob ensure that the burners and burner

caps are correctly placed within their position.

Warning: If there is no electricity on appliance, to ignite the burner a

lighter should be used;

- Push in and turn the knob anti-clockwise to the ignitionsymbol,

- While pushing in the button ignite the burner by using a lighter and

keep button pushed in 5 seconds after ignition.

GENERALADVISE

For best results, use cooking vessels with a flat surface. The size of

the surface should match the gas burner side asfollows.TableA.

4. MAINTENANCE AND CLEANING

Before cleaning the hob, ensure the appliance has cooled down.

Remove the plug from the socket or (if connected directly) switch off

the electricity supply.

Cleaning and user maintenance shall not be made by children without

supervision

Never use abrasives, corrosive detergents, bleaching agents or

acids. Avoid any acid or alkaline substances (lemon, juice, vinegar

etc.) on the enamelled, varnished or stainless steel sections.

When cleaning the enamelled, varnished or chrome sections, use

warm soapy water or a non caustic detergent. For stainless steel use

an appropriate cleaning solution.

The burners can be cleaned with soapy water. To restore their original

shine, use a household stainless steel cleaner. After cleaning, dry the

burners and replace.

It is important the Burners are replaced correctly.

Chromed grids and burners

Chromed grids and burners have a tendency to discolour with use.

This does not jeopardize the functionality of the hob.

Our After Sales Service Centre can provide spare parts if required.

For smaller containers the gas burner should be regulated so that the

flame does not overlap the base of the pan. Vessels with a concave or

convex base should not be used.

WARNING: If a flame is accidentally extinguished, turn the knob

to the off position and do not attempt to re-ignite if for at least 1

minute.

If over the years the gas taps become stiff to turn it is necessary to

lubricate them.

Such operation must be carried out only by qualified Service

Engineers.

2)Tighten the joints with the spanner, remembering to twist the

pipes into position.

3)Attach fitting C to mains gas supply using rigid copper pipe or

flexible steel pipe.

IMPORTANT: carry out a final check for leaks on the pipe

connections using a soapy solution. NEVER USE A FLAME.

Also, make sure that the flexible pipe cannot come into contact

with a moving part of the cabinet (eg.adrawer) and that it is not

situated where it could be damaged.

Warning: If gas can be smelt in the vicinity of this appliance turn off

the gas supply to the appliance and call the engineer directly. Do not

search for a leak with a naked flame.

Before using burner, be sure, grid perimeters center the burner as

below figure.

If you are using Cast Iron Grids; underneath the grid, position of it is

stated. Be sure for the exact grid is usedincorrect position.

05 GB

This appliance has been designed for non-professional, i.e. domestic, use.

Table 1

This appliance is marked according to the European

directive 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE). WEEE contains both

polluting substances (which can cause negative

consequences for the environment) and basic

components (which can be re-used). It is important to

have WEEE subjected to specific treatments, in order

to remove and dispose properly all pollutants, and

recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not

become an environmental issue; it is essential to follow some basic

rules:

• WEEE shall not be treated as household waste.

• WEEE shall be handed over to the relevant collection points

managed by the municipality or by registered companies. In many

countries, for large WEEE, home collection could be present.

• When you buy a new appliance, the old one may be returned to the

retailer who has to collect it free of charge on a one-to-one basis, as

long as the equipment is of equivalent type and has the same

functions as the supplied equipment.

Declaration of compliance: This equipment, in the parts intended to

come into contact with food, complies with the regulations laid down in

EEC directives 89/109.

The appliance complies with European Directive 2009/142/EC (GAD)

and starting from 21/04/2018 with Gas Appliances Regulation

2016/426 (GAR).

6. PROTECTION OF THE ENVIRONMENT

The Manufacturer will not be responsible for any inaccuracy resulting

from printing or transcript errors contained in this brochure. We

reserve the right to carry out modifications to products as required,

including the interests of consumption, without prejiudice to the

characteristics relating to safety or function.

By placing the mark on this product, we are confirming

compliance to all relevant European safety, health and environmental

requirements which are applicable in legislation for this product.

5. AFTERCARE

Before calling out a Service Engineer please check the following:

• that the plug is correctly inserted and fused;

• that the gas supply is not faulty.

If the fault cannot be detected:

Switch off the appliance and call the After Service Centre. DO NOT

TAMPER WITH THE APPLIANCE.

Burner Plate

Burner

Type

FFD

Aux 1kW

Sr 1,75 kW

R 2,7 kW

Nominal Heat Input

G20/20 mbar

G30/28-30 mbar

Installation Class

Voltage V/Frequency Hz

Electrical Input Power

Electric Ignition

Product Dimension

220-240 V/ 50/60 Hz

YES

595x510

UH60ML

YES

4 Gas

Aux/2SR/R

7,2 kW

686 l/h

524 g/h

560 mm

480 mm

min 70 mm

min 600 mm

min 50 mm

min 170 mm (60 cm)

min 250 mm (75 cm)

Figure 2Figure 1

1/2 GAS

CONICAL

CYLINDRICAL

CONICAL

INJECTOR

Figure 6

Figure 7

Figure 8

25 - 45 mm

min. 5 mm

min. 10 mm

min.

50 mm

25 - 45 mm

min. 5 mm

Figure 3

min.

50 mm

min. 10 mm

min.

50 mm

min.

50 mm

120 cm

180 cm

Figure 5

Min. 70 cm

Figure 4

GAS TYPEHOBS

Max - Min Max - Min Max - Min Max - Min Max - Min Max - Min Max - Min

72X

(1Kw-0,3Kw)

70X

(1Kw-0,3Kw)

74F1

(1Kw-0,3Kw)

72F1

(1Kw-0,3Kw)

(1Kw-0,34Kw)

43H2

(1Kw-0,39Kw)

97Z

(1.75Kw-0.44Kw)

102F3

(1.75Kw-0.44Kw)

(1.75Kw-0.51Kw)

58M

(1.75Kw-0.58Kw)

91Z

(1.75Kw-0.44Kw)

98Y

(1.75Kw-0.44Kw)

109Y

(2.7Kw-0.75Kw)

120F3

(2.7Kw-0.75Kw)

(2.7Kw-0.83Kw)

73S

(2.7Kw-0.96Kw)

110F3

(2.7Kw-0.75Kw)

125F3

(2.7Kw-0.75Kw)

II2HS3B/P

II2H3+

Efficiency Decleration 201 /4 66/EU

UH60ML

AUX FR SR RR SR RL R FL

60 % 60 % 57,6 %

SINGLE BURNER EFFICENCY

MEDIUM %5 ,92

G20/G25-20/25 mbar

II2EK B/P3

G25.1 25 mbar

EN 30-2-1

GB - IE

The manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We reserve the right

to carry out modifications to products as required, including the interests of con sumption, without prejudice to the characteri stics relating to safety or

function.

09.2018 • REV:0 • 42823718

Výrobce nezodpovídá za nepřesnosti obsažené v této příručce vzniklé při tisku nebo překladu. Vyhrazujeme se právo provádět úpravy výrobku podle

potřeby, aniž by byly dotčeny charakteristiky vztahující se kbezpečnosti nebo provozu.

Der Hersteller übernimmt keine Haftung für eventuelle Druck- oder Übersetzungsfehler dieser Bedienungsanleitung. Der Hersteller behält sich vor

technische Änderungen zurVerbesserung der Produktqualität imInteresse des Endverbrauchers vorzunehmen.

La empresa constructora declina toda responsabilidad derivada de eventuales errores de impresión contenidos en el presente libro. Se reserva ademásel

derecho de realizarlas modificaciones que se consideren útiles a los productossin comprometer las características esencial es.

Producent nie będzie ponosić odpowiedzialności za jakiekolwiek niedokładności wynikające z druku lub błęd w tłumaczenia występujące w niniejszejЧ

broszurze. Zastrzegamy sobie prawo do wprowadzania modyfikacji produktu zgodnie z potrzebami, w tym w interesie konsumenta, bez szk d dlaЧ

charakterystyk dotyczących bezpieczeństwalub działania.

Üretici, bu klavuzda meydana gelecek baskı hatalarından sorumlu değildir. Üretici gerekli olması durumunda ürünün emniyet ve işlevine ilişkin olmamak

kaydıyla üründe değişiklikyapma hakkını saklı tutar.

Производитель не несет ответственности за опечатки и неточности, которые могут встретиться в данной инструкции. Мы оставляем за собой

право вносить изменения в конструкцию выпускаемых нами изделий с целью улучшения качества выпускаемой продукции. При этом основные

функции изделияи его безопасность будут оставаться неизменными.

Proizvajalec ni odgovoren za napake v tej knjižici, ki bi nastale ob tisku ali prepisu. Pridržujemo si pravico izvajanja potrebnih sprememb na izdelku, tudi tistih,

ki se nanašajona porabo, brez škodeza varnost in funkcionalnost naprave.

La Ditta costruttrice declina ogni responsabilità per eventuali errori di stampa contenuti nel presente libretto. Si riservainoltre il diritto di apportare le modifiche

che si renderannoutili ai propri prodotti senza compromettere le caratteristiche essenziali.

O fabricante não será responsável por quaisquer imprecisões resultantes de impressão ou transcrição de erros contidos na presente brochura.

Reservamo-nos ao direito de efectuar alterações aos produtos, conforme necessário, incluindo as taxas de consumo, sem prejuízo das características

relacionadas com asegurança ou funcionamento.

Le constructeur décline toute responsabilité concernant d'éventuelles inexacitudes imputables à des erreurs d'impression ou de transcription contenue dans

cette notice. Le constructeur se réserve le droit de modifier les produits en cas de nécessité, même dans l'intérêt de l'utilisation, sans causer de préjudices

aux caractéristiques defonctionnement de sécurité des appareils.

A gyártó nem vállal felelősséget az ebben a kiadványban előforduló nyomtatási és elírási hibákból eredő pontatlanságokért. A biztonsággal vagy a

működéssel kapcsolatos jellemzőksérelme nélkül fenntartjuk a jogot a termékek szükség szerintiváltoztatására.

Producătorul nu se face responsabil pentru erorile de printare din acest manual. Ne rezervăm dreptul de a realiza modificări asupra produselor fără a afecta