LG 24LF450B Manual de utilizare

Please read this manual carefully before operating your

set and retain it for future reference.

www.lg.com

Safety and Reference

OWNER’S MANUAL

LED TV*

* LG LED TV applies LCD screen with LED backlights.

*MFL68702435*

P/NO : MFL68702435(1503-REV00)

Printed in Korea

ENGLISH

Please read these safety precautions carefully before

using the product.

environments:

t A location exposed to direct sunlight

t An area with high humidity such as a bathroom

t Near any heat source such as stoves and other devices that

produce heat

t Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

t An area exposed to rain or wind

t Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

cause a re hazard.

TV connecting/disconnecting device to AC mains

electric supply. This plug must remain readily attached and operable

when TV is in use.

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

e sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

t power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

such as a heater. This may cause a re or an electric shock hazard.

Otherwise, this may result in re or electric shock.

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

outlet. Otherwise, this may result in re due to over-heating.

ENGLISH

devices. Otherwise, this may result in injury or damage to the product.

Desiccant

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out

of the reach of children.

Otherwise, the TV may fall over, which may cause serious injury.

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

danger of combustion/explosion or re due to careless handling of the

inammable substances.

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

substance (thinner or benzene). Fire or electric shock accident can

occur.

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

You may be electrocuted.

windows and ventilate. It may cause a re or a burn by a spark.

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

ENGLISH

y of the following occur, unplug the product immediately and

contact your local service centre.

t The product has been impacted by shock

t The product has been damaged

t Foreign objects have entered the product

t The product produced smoke or a strange smell

This may result in re or electric shock.

TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

ater enters or comes into contact with TV, AC adapter or power

cord please disconnect the power cord and contact service centre

immediately . Otherwise ,this may result in electric shock or re.

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction or product deformation.

or electric shock.

oduct where no radio wave occurs.

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

ou install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

Only use the attachments / accessories specied by the manufacturer.

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

ENGLISH

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

remote control.

batteries to overheat and leak.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open replace and electric heaters.

Do not place non-rechargeable batteries in charging device.

e sure there are no objects between the remote control and its

sensor.

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

ollow the installation instructions below to prevent the product

from overheating.

t The distance between the product and the wall should be more

than 10cm.

t Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

t Do not install the product on a carpet or cushion.

t Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

a re hazard.

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

ENGLISH

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

the plug.

Don’t pull at the cord to unplug the power cord from the power board,

as this could be hazardous.

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

product is heavy. Otherwise, this may result in injury.

product.

Accumulated dust can cause mechanical failure.

er all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

oduct feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

million to six million pixels. You may see tiny black dots and/or brightly

coloured dots (red, blue or green) at a size of 1ppm on the panel. This

does not indicate a malfunction and does not aect the performance

and reliability of the product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

ENGLISH

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

menu, scene from a video game) for a prolonged time may cause

damage to the screen, resulting in retention of the image, which is

known as image sticking. The warranty does not cover the product for

image sticking.

Avoid displaying a xed image on your television’s screen for a

prolonged period (2 or more hours for LCD, 1 or more hours for Plasma).

Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking

may occur on the borders of the panel.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

Generated Sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV (e.g. electric

mosquito-swatter). This may result in product malfunction.

Preparing

TE

t Image shown may dier from your TV.

t Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

t The available menus and options may dier from the input source

or product model that you are using.

t New features may be added to this TV in the future.

t The TV can be placed in standby mode in order to reduce the power

consumption. And the TV should be turned o if it will not be

watched for some time, as this will reduce energy consumption.

t The energy consumed during use can be signicantly reduced if the

level of brightness of the picture is reduced, and this will reduce

the overall running cost.

t The items supplied with your product may vary depending on the

model.

t Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

t For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

*B

<

=

t Use a certied cable with the HDMI logo attached.

t If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur. (Recommended HDMI Cable Types)

- High-Speed HDMI

®

/

TM

cable (3 m or less)

- High-Speed HDMI

®

/

TM

cable with Ethernet (3 m or less)

ENGLISH

t Do not use any unapproved items to ensure the safety and product

life span.

t Any damage or injuries caused by using unapproved items are not

covered by the warranty.

t Some models have a thin lm attached on to the screen and this

must not be removed.

t When attaching the stand to the TV set, place the screen facing

down on a cushioned table or at surface to protect the screen

from scratches.

t Make sure that the screws are fastened completely. (If they are

not fastened securely enough, the TV may tilt forward after being

installed.) Do not use too much force and over tighten the screws;

otherwise screw may be damaged and not tighten correctly.

Maintenance

Cleaning your TV

Clean your TV regularly to keep the best performance and to extend the

product lifespan.

t Make sure to turn the power o and disconnect the power cord and

all other cables rst.

t When the TV is left unattended and unused for a long time,

disconnect the power cord from the wall outlet to prevent possible

damage from lightning or power surges.

Screen, frame, cabinet and stand

To remove dust or light dirt, wipe the surface with a dry, clean, and

soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in

clean water or a diluted mild detergent. Then wipe immediately with

a dry cloth.

t Avoid touching the screen at all times, as this may result in damage

to the screen.

t Do not push, rub, or hit the screen surface with your ngernail or a

sharp object, as this may result in scratches and image distortions.

t Do not use any chemicals as this may damage the product.

t Do not spray liquid onto the surface. If water enters the TV, it may

result in re, electric shock, or malfunction.

Power cord

Remove the accumulated dust or dirt on the power cord regularly.

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

t It is recommended to move the TV in the box or packing material

that the TV originally came in.

t Before moving or lifting the TV, disconnect the power cord and

all cables.

t When holding the TV, the screen should face away from you to

avoid damage.

Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

When transporting a large TV, there should be at least 2 people.

t When transporting the TV by hand, hold the TV as shown in the

following illustration.

When transporting the TV, do not expose the TV to jolts or

excessive vibration.

t When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

t Do not apply excessive pressure to cause exing /bending of frame

chassis as it may damage screen.

t When handling the TV, be careful not to damage the protruding

joystick button.

t Avoid touching the screen at all times, as this may result in damage

to the screen.

t Do not move the TV by holding the cable holders, as the cable

holders may break, and injuries and damage to the TV may occur.

ENGLISH

Using the joystick button

(Image shown may dier from your TV.)

You can simply operate the TV functions, pressing or moving the joystick

button up, down, left or right.

Joystick Button

When the TV is turned o, place your

nger on the joystick button and

press it once and release it.

When the TV is turned on, place your

nger on the joystick button and

press it once for a few seconds and

release it. (However, if the Menu

button is on the screen, pressing and

holding the joystick button will let

you exit the Menu.)

Control

If you place your nger over the

joystick button and move it left or

right, you can adjust the volume level

you want.

Control

If you place your nger over the

joystick button and move it up or

down, you can scrolls through the

saved programmes you want.

Adjusting the Menu

When the TV is turned on, press the joystick button one time. You can

adjust the Menu items moving the joystick button up, down, left or

right.

Turns the power o.

Clears on-screen displays and returns to TV viewing.

TE

t When your nger over the joystick button and push it to the up,

down, left or right, be careful not to press the joystick button. If you

press the joystick button rst, you may not be able to adjust the

volume level and saved programmes.

Mounting on a table

(Depending on model)

1 Lift and tilt the TV into its upright position on a table.

t Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

t Do not place the TV near or on sources of heat, as this may result in

re or other damage.

Using the kensington security

system

(This is not available for all models.)

t Image shown may dier from your TV.

The Kensington security system connector is located at the rear of the

TV. For more information of installation and using, refer to the manual

provided with the Kensington security system or visit http://www.

kensington.com. Connect the Kensington security system cable between

the TV and a table.

ENGLISH

(This feature is not available for all models.)

Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

t If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

t Make sure that children do not climb on or hang on the TV.

TE

t Use a platform or cabinet that is strong and large enough to

support the TV securely.

t Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

Mounting on a wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the

use of LG’s wall mount bracket. When you do not use LG’s wall mount

bracket, please use a wall mount bracket where the device is adequately

secured to the wall with enough space to allow connectivity to external

devices.

10 cm

Standard dimensions for the wall mount kits are described in the

following table.

Separate purchase(Wall Mounting Bracket)

Model

28LF45**

28LF55**

Wall Mount (A x B) 100 x 100

Standard screw

Number of screws

Wall mount bracket

A

B

t Disconnect the power rst, and then move or install the TV.

Otherwise electric shock may occur.

t Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

t If you install the TV on a ceiling or slanted wall, it may fall and

result in severe injury. Use an authorised LG wall mount and

contact the local dealer or qualied personnel.

t Do not over tighten the screws as this may cause damage to the TV

and void your warranty.

t Any damages or injuries by misuse or using an improper accessory

are not covered by the warranty.

t Screw length from outer surface of back cover should be under 8

mm.

Back Cover

: M4 x L10

Wall mount Pad

Back Cover

Max.8 mm

ENGLISH

TE

t The wall mount kit includes an installation manual and necessary

parts.

t The wall mount bracket is not provided. You can obtain additional

accessories from your local dealer.

t The length of screws may dier depending on the wall mount.

Make sure to use the proper length.

t For more information, refer to the manual supplied with the wall

mount.

Connections (notications)

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

TE

t The external device connection may dier from the model.

t Connect external devices to the TV regardless of the order of the

TV port.

t If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

t Refer to the external equipment’s manual for operating

instructions.

t If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

t In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

t In PC mode, some resolution settings may not work properly

depending on the graphics card.

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

t Use a signal splitter to use more than 2 TVs.

t If the image quality is poor, install a signal amplier properly to

improve the image quality.

t If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

t An antenna cable and converter are not supplied.

t Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,

HE-AAC

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω).

CI module connection

View the encrypted (pay) services in digital TV mode.

t Check if the CI module is inserted into the PCMCIA card slot in the

right direction. If the module is not inserted properly, this can

cause damage to the TV and the PCMCIA card slot.

t If the TV does not display any video and audio when CI+ CAM is

connected, please contact to the Terrestrial/Cable/Satellite Service

Operator.

Euro Scart connection

Transmits the video and audio signals from an external device to the

TV set. Connect the external device and the TV set with the euro scart

cable.

Type

Current

input mode

AV1

(TV Out

1

)

Digital TV Digital TV

Analogue TV, AV

Analogue TVComponent

HDMI

1 TV Out : Outputs Analogue TV or Digital TV signals.

t Any Euro scart cable used must be signal shielded.

ENGLISH

t Please be sure to connect the TV to the AC-DC power adapter

before connecting the TV’s power plug to a wall power outlet.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

USB port supports 0.5A electric current. If you need more electric

current in case of HDD, use the separate power adaptor.

Remote control

(Depending on model)

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the

ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

t Do not mix old and new batteries, as this may damage the remote

control.

t The remote control will not be included for all sales market.

Make sure to point the remote control toward the remote control sensor

on the TV.

A

B

(POWER)

alls your preferred subtitle in digital mode.

enabled.

Changes the input source.

Number buttons

o the previously viewed programme.

B

ws programme guide.

es all sounds.



 Moves to the previous or next screen.

ENGLISH

C

D

Teletext buttons ( )

teletext.

screen.

Navigation buttons (up/down/left/right)

or options.

o the previous level.

Clears on-screen displays and returns to TV viewing.

D

Accesses the AV devices connected with the HDMI

cable through HDMI-CEC. Opens the SIMPLINK menu.

on model)

Control buttons ( )

menus, or the SIMPLINK compatible devices (USB,SIMPLINK).

Coloured buttons

( , reen, lue)

Adjusts the brightness of the screen by

controlling the screen backlight.

TE

t On MHEG channel, you cannot adjust the backlight with the yellow

or blue key.

Licenses

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

tured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby

Laboratories.

and the HDMI logo are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.

plays DivX® video.

To play purchased DivX movies, rst register your device at vod.divx.

com. Find your registration code in the DivX VOD section of your

device setup menu.

DivX Certied® to play DivX® video up to HD 1080p, including

premium content.

DivX®, DivX Certied® and associated logos are trademarks of DivX,

LLC and are used under license.

Covered by one or more of the following U.S. patents :

7,295,673; 7,460,668; 7,515,710; 7,519,274.

Open source software

notice information

To obtain the source code under GPL, LGPL, MPL and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

ENGLISH

Automatically Setting Up Programme

SETTINGS SETUP Auto Tuning

Automatically tunes the programmes.

t If Input Source is not connected properly, programme registration

may not work.

t

Auto Tuning ogrammes that are currently

broadcasting.

t If Lock System -up window will appear asking

for password.

To adjust picture with Picture Wizard

SETTINGS

PICTURE Picture Wizard III

[Depending on model]

Calibrates and adjusts for optimum picture quality using the remote

control and the Picture Wizard without expensive pattern devices or

help from a specialist.

To select Picture Mode

SETTINGS

PICTURE Picture Mode

programme.

t Vivid eightens contrast, brightness and sharpness to display

vivid images.

t Standard isplays images in standard levels of contrast,

brightness and sharpness.

t Eco/APS epending on model]

The Energy Saver feature changes settings on the TV to reduce

power consumption.

t Cinema/Game isplays the optimum picture for movie, game.

t Sport epending on model] Optimizes the video image for

high and dynamic actions by emphasizing primary colours such as

white, grass, or sky blue.

t Expert 1, 2 or adjusting picture quality that

allows experts and amateurs to enjoy the best TV viewing. This

is the adjustment menu provided for ISF-certied picture tuning

professionals. (ISF logo can only be used on ISF-certied TVs.)

ISFccc: Imaging Science Foundation Certied Calibration Control

t Depending on input signal, available range of picture modes may

dier.

t t mode is for picture tuning professionals to control

and ne-tune using a specic image. For normal images, the

eects may not be dramatic.

t The ISF function is only available on some models.

To set advanced control

SETTINGS

PICTURE Picture Mode Advanced Control /

Expert Control

for a special screen. First select a Picture Mode our choice.

t Dynamic Contrast djusts the contrast to the optimal level

according to the brightness of the image.

t Dynamic Colour djusts colours to make the image appear in

more natural colours.

t Skin Colour ets Skin colour spectrum separately to implement

the skin colour as dened by the user.

t Sky Colour olour is set separately.

t Grass Colour tural colour spectrum (meadows, hills, etc.) can

be separately set.

t Gamma ets the gradation curve according to the output of

picture signal in relation to the input signal.

t Colour Gamut elects the range of colours that can be

expressed.

t Edge Enhancer ws clearer and distinctive yet natural edges

of the video.

t Expert Pattern epending on model]

Patterns used for expert adjustment.

t Colour Filter ilters a specic colour spectrum in RGB colours to

ne-tune colour saturation and hue accurately.

t Colour Temperature djusts the overall tone of the screen

as desired. In Expert mode, detailed ne-tuning can be set via

Gamma method, etc.

t Colour Management System This is a system that experts use

when they adjust colour with a test pattern. They can select from

six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow)

without aecting other colours. For normal images, adjustments

may not result in noticeable colour changes.

t Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

ENGLISH

To set additional picture options

SETTINGS

PICTURE Picture Mode Picture Option

Adjusts detailed setting for images.

t Noise Reduction liminates noise in the picture.

t MPEG Noise Reduction liminates noise generated while

creating digital picture signals.

t Black Level djusts the brightness and contrast of the screen

to suit the black level of the input picture by using the blackness

(black level) of the screen.

t Real Cinema ptimizes the screen for movie viewing.

t Motion Eye Care / Smart Energy Saving epending on

model] Saves power consumption by adjusting the brightness

corresponding to the movement of the image on the screen.

t Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

To use Energy Saving feature

SETTINGS

PICTURE Energy Saving

es power consumption by adjusting screen brightness.

t Off Turns o the Energy Saving mode.

t Minimum / Medium / Maximum pplies the pre-set Energy

Saving mode.

t Screen Off creen is turned o and only sound is played. Press

any button except Power button on the remote control to turn the

screen back on.

To use TV speaker

SETTINGS

AUDIO Sound Out TV Speaker

Sound is output through the TV speaker.

To use Headphone

SETTINGS AUDIO Sound Out Headphone

Sound is output through the headphone connected to the earphone/

headphone port.

To synchronize audio and video

SETTINGS AUDIO AV Sync. Adjust

Synchronizes video and audio directly when they do not match.

t If you set AV Sync. Adjust ON ou can adjust the sound output

(TV speakers) to the screen image.

To use SIMPLINK

[Depending on model]

SIMPLINK is a feature that enables you to control and manage various

multimedia devices conveniently via the SIMPLINK menu.

1 Connect the TV’s

HDMI IN

output terminal using an HDMI cable.

2 Select INPUT SIMPLINK

SIMPLINK menu window appears.

3 In SIMPLINK Setting window, set SIMPLINK function to ON

4 In SIMPLINK menu window, selects the device you want to control.

t This function is only compatible with devices with the SIMPLINK

logo.

t To use the SIMPLINK function, you need to use a high-speed HDMI®

cable (with CEC (Consumer Electronics Control) feature added).

High-speed HDMI® cables have the No. 13 pin connected for

information exchange between devices.

t If you switch to another input, the SIMPLINK device will stop.

t If a third-party device with the HDMI-CEC function is also used, the

SIMPLINK device may not work normally.

t If you select or play media from a the device with a home theatre

function, the

HT Speaker(Speaker) omatically connected.

ENGLISH

tion description

t

Direct Play ys the multimedia device on the TV instantly.

t Select multimedia device elects the desired device via the

SIMPLINK menu to control it from the TV screen instantly.

t Disc playback e with the TV

remote control.

t Power off all devices When you power o the TV, all connected

devices are turned o.

t Sync Power on When the equipment with SIMPLINK function

connected HDMI terminal starts to play, the TV will automatically

turn on.

t Speaker epending on model]

Select speaker either on the home theatre unit or the TV.

To set password

SETTINGS LOCK Set Password

The initial password is set to ‘0000’.

t When France is selected for Country, password is not ‘0000’ but

‘1234’.

t When France is selected for Country, password cannot be set to

‘0000’.

To return Factory Reset

SETTINGS OPTION Factory Reset

The TV turns itself o and back on, and all settings are reset.

t When Lock System e, a pop-up window appears and asks

for password.

t Do not turn o the power during initialization.

To remove the USB device

Q.MENU USB Device

When you see a message that the USB device has been removed,

separate the device from the TV.

t Once a USB device has been selected for removal, it can no longer

be read. Remove the USB storage device and then re-connect it.

Using a USB storage device - warning

t If the USB storage device has a built-in auto recognition program

or uses its own driver, it may not work.

t Some USB storage devices may not work or may work incorrectly.

t Use only USB storage devices formatted with the Windows FAT32

or NTFS File System.

t For external USB HDDs, it is recommended that you use devices

with a rated voltage of less than 5 V and a rated current of less

than 500 mA.

t It is recommended that you use USB memory sticks of 32 GB or less

and USB HDDs of 2 TB or less.

t If a USB HDD with power-saving function does not work properly,

turn the power o and on. For more information, refer to the user

manual of the USB HDD.

t Data in the USB storage device can be damaged, so be sure to back

up important les to other devices. Data maintenance is the user’s

responsibility and the manufacturer is not responsible for data loss.

My Media supporting le

t Maximum data transfer rate : 20 Mbps (Mega bit per second)

t External supported subtitle formats : *.srt (SubRip), *.smi (SAMI),

*.sub (SubViewer, MicroDVD, DVDsubtitleSystem, SubIdx(Vobsub)),

*.ass/*.ssa (SubStation Alpha), *.txt (TMplayer), *.psb (PowerDivX)

t Internal supported subtitle formats: *.dat/*.mpg/*.mpeg/*.

vob (DVD Subtitle), *.ts/*.tp/*.m2ts/ (DVB Subtitle), *.mp4 (DVD

Subtitle, UTF-8 Plain Text), *.mkv (ASS, SSA, UTF-8 Plain Text,

Universal Subtitle Format, VobSub, DVD Subtitle), *.divx/*.avi

(XSUB

1

, XSUB+)

1 XSUB : Supports internal subtitles generated from DivX6

ENGLISH

Supported Video Formats

t Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)

t .asf, .wmv

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC, VC1(WMV3, WVC1), MP43

[Audio] WMA Standard, WMA9(Pro), MP3, AAC, AC3, MP3, 3D WMV

Single Stream.

t divx, .avi

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC

[Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I, MPEG-1 Layer II,

Dolby Digital, MPEG-1 Layer III (MP3), *DTS

t .ts, .trp, .tp, .mts, .m2ts

[Video] H.264/AVC, MPEG-2, AVS, VC1

[Audio] MPEG-1 Layer I, MPEG-1 Layer II, MPEG-1 Layer III (MP3),

Dolby Digital, Dolby Digital Plus, AAC, HE-AAC, *DTS

t .vob

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1 Layer II, DVD-LPCM

t .mp4, .m4v, .mov

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XVID, H.264/AVC

[Audio] AAC, MPEG-1 Layer III (MP3), *DTS

t .mkv

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XVID, H.264/AVC

[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III (MP3), *DTS, LPCM

t motion JPEG

[Video] MJPEG

[Audio] LPCM, ADPCM

t .mpg, .mpeg, .mpe

[Video] MPEG-1, MPEG-2

[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby Digital, LPCM

t dat

[Video] MPEG-1, MPEG-2

[Audio] MP2

t v

[Video] Sorenson H.263, H.264/AVC

[Audio] MP3, AAC, HE-AAC

t *rm, *rmvb

[Video] RV30, RV40

[Audio] Dolby Digital, AAC, HE-AAC, RA6(Cook)

t 3gp, 3gp2

[Video] H.264/AVC, MPEG-4 Part2

[Audio] AAC, AMR(NB/WB)

t *DTS / *rm / *rmvb : Depending on model

Supported Audio Formats

t File type : mp3

[Bit rate] 32 Kbps - 320 Kbps

[Sample freq.] 16 kHz - 48 kHz

[Support] MPEG1, MPEG2, Layer2, Layer3

t File Type : AAC

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] ADIF, ADTS

t File Type : M4A

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] MPEG-4

t File Type : WMA

[Bit rate] 128 Kbps ~ 320 Kbps

[Sample freq.] 8 kHz ~ 48 kHz

[Support] WMA7, WMA8, WMA9 Standard

t File Type : WMA 10 Pro

[Bit rate] ~ 768 Kbps

[Channel / Sample freq.]

M0 : up to 2 Channel @ 48 kHz

(Except LBR mode),

M1 : up to 5.1 Channel @ 48 kHz,

M2 : up to 5.1 Channel @ 96 kHz

[Support] WMA 10 Pro

t File Type : OGG

[Bit rate] Free Format

[Sample freq.] ~ 48 kHz

[Support] OGG Vorvis

Supported Photo Formats

t Category : 2D (jpeg, jpg, jpe)

[Available le type] SOF0: Baseline,

SOF1 : Extend Sequential,

SOF2 : Progressive

[Photo size] Minimum : 64 x 64,

Maximum : Normal Type: 15360 (W) x 8640 (H),

Progressive Type : 1920 (W) x 1440 (H)

t Category : BMP

[Photo size] Minimum : 64 x 64, Maximum : 9600 x 6400

t Category : PNG

[Available le type] Interlace, Non-Interlace

[Photo size] Minimum : 64 x 64, Maximum : Interlace : 1200 x 800,

Non-Interlace : 9600 x 6400

t BMP and PNG format les may be slower to display than JPEG.

ENGLISH

To obtain detailed User Guide information, please visit www.lg.com.

External control device

setup

To obtain the external control device setup information, please visit

www.lg.com.

Troubleshooting

Cannot control the TV with the remote control.

t Check the remote control sensor on the product and try again.

t Check if there is any obstacle between the product and the remote

control.

t Check if the batteries are still working and properly installed (

to

, to ).

No image display and no sound is produced.

t Check if the product is turned on.

t Check if the power cord is connected to a wall outlet.

t Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

t Check the power control settings. The power supply may be

interrupted.

t Check if the

Automatic Standby Sleep

Timer Off Time tivated in the TIME .

t If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is

displayed.

t Turn the TV o/on using the remote control.

t Reconnect the HDMI cable.

t Restart the PC with the TV on.

www.lg.com

"L¨T[»M¨LIBT[OMBUCBW¨UFMFFMďUUŻHZFMNFTFOPMWBTTBFMB[

¹UNVUBU²U¨TďSJ[[FNFHNFSUL¨TďCCT[»LT¨HFMFIFUS

#J[UPOTHJ²WJOU¨[LFE¨TFL

HASZNÁLATI ÚTMUTATÓ

LED TV*

* Az LG LED TV megnevezés a LED háttérfénnyel ellátott

LCD képernyőkre vonatkozik.

MAGYAR

A készülék használata előtt kérjük, gyelmesen

olvassa el a következő biztonsági óvintézkedéseket.

környezetekbe:

t Közvetlen napsugárzásnak kitett helyek

t Nedves területek, például fürdőszoba

t Hőforrás közelébe, például kályhák és egyéb hőt kibocsátó

eszközök

t Konyhai berendezések vagy párologtató készülékek közelébe, ahol

könnyen ki vannak téve gőznek vagy olajnak

t Esőnek vagy szélnek kitett helyek

t Vizet tartalmazó tárgyak, például vázák közelébe

Ellenkező esetben tűz, áramütés, hibás működés vagy deformálódás

következhet be.

Ez tűzveszélyes lehet.

zati csatlakozódugó a készülék áramtalanítására szolgál. A

dugónak könnyen hozzáférhetőnek kell lennie.

nedvesek vagy porosak, törölje teljesen szárazra, illetve portalanítsa.

Ellenkező esetben a nedvesség halálos áramütést okozhat.

ábelt minden esetben földelt konnektorhoz csatlakoztassa.

(Kivéve a földelés nélküli eszközöket.)

Halálos áramütést vagy sérülést szenvedhet.

ábelt szorosan csatlakoztassa az aljzathoz.

A nem megfelelően csatlakoztatott tápkábel tüzet okozhat.

fűtőtesthez. Ez tűzveszélyes és áramütést okozhat.

ábelre se nehéz tárgyat, se készüléket ne helyezzen.

Ellenkező esetben tüzet vagy áramütést okozhat.

tenna kábelét az épület belső és külső tere között úgy,

hogy ne juthasson bele esővíz.

Az eső tönkreteheti a készülék belsejét, és áramütést is okozhat.

TV-készüléket szerel a falra, gondoskodjon arról, hogy azt ne a TV

hátulján lévő táp- és jelkábelnél fogva akassza fel.

Ez tüzet vagy áramütést okozhat.

számára készült aljzatba.

Ellenkező esetben a túlmelegedés miatt tűz keletkezhet.

Pagina se încarcă ...

LG 24LF450B Manual de utilizare

LG 24LF450B Manual de utilizare

în alte limbi

Lucrări conexe