Yamaha CDC-745 Manualul proprietarului

Categorie
CD playere
Tip
Manualul proprietarului

Acest manual este potrivit și pentru

Natural Sound Compact Disc Player
5-Disc Carousel Auto-Changer
PLAYXCHANGE; Disc Changing Capability while Playing Another
Random Access Programmable Play
Random-Sequence Play
Single Track/Entire Disc/All Disc Repeat Play
Automatic Tape-Programming
Automatic Peak Level Searching Capability
Program Data Filing Capability
Disc Scanning Capability Useful for Disc Searching or Disc Checking
Display Brightness Changing Capability
CD Synchronized Recording with a Compatible YAMAHA Tape Deck
Optical Digital Output
Remote Control Capability
IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Explanation of Graphical Symbols
CAUTION
Thank you for selecting this YAMAHA Compact Disc Player.
OWNER’S MANUAL
CONTENTS
Safety Instructions.................... 2
Connections............................. 4
Identification of Components.... 5
Loading Discs/Disc Play........... 7
Random-Sequence Play ........ 11
Program Play.......................... 12
Repeat Play............................ 16
Index Search.......................... 16
Track Programming for
Recording to Tape...................17
CD Synchronized Recording...21
Notes about the Remote
Control Transmitter................. 22
Notes about Handling
Compact Discs....................... 22
Troubleshooting...................... 23
Specifications......................... 23
CDC-845 / 745
2
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and cart combination
to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that
produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
1 To ensure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not expose
to rain and water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
5 Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
6 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
7 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that your unit
is faulty.
CAUTION FOR CARRYING THIS UNIT
Be sure not to carry or tip the unit with discs remaining in it.
CAUTION FOR MOVING THIS UNIT
When moving this unit, first remove all discs from the disc
tray and close the tray by pressing the OPEN/CLOSE
button, and then switch off the power after you confirm that
the display has turned as follows.
Never switch off the power if the display does not turn as
above, otherwise the unit will get out of order during
moving because the internal mechanism is not locked.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
3
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personel only.
To avoid electrical shock, do not open the unit. Refer
servicing to qualified personnel only.
DANGER: The use of optical instrument with this product will
increase eye hazard.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
DANGER
Invisible laser radiation when open and interlock failed or
defeated.
Avoid direct exposure to beam.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you to
avoid prolonged exposure from excessive
volume levels.
We Want You Listening For A Lifetime
FCC INFORMATION
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
WARNING
4
CONNECTIONS
Before making any connections, switch OFF the power to
the unit and the amplifier or other component.
Connections should be made to the correct input terminals
of the amplifier or other component.
If the placement of this unit causes noise to other
equipment, such as a tuner, separate them from each other.
LINE OUT
CD DIGITAL IN
OPTICAL
DIGITAL
AUDIO
OUT
OPTICAL
To AC outlet
This unit
Amplifier
Optical fiber cable
(not included)
When the LINE OUT (analog) terminals of this
unit are used (
)
Be sure that the left (“L”) and right (“R”) LINE OUT terminals
are connected to the corresponding (left and right) terminals
of the amplifier or other component.
Connect the “LINE OUT” terminals to the “CD” (or “AUX”)
terminals of the amplifier. If the amplifier does not have
such terminals, use the “TAPE PB” terminals. For additional
details concerning these connections, refer to the operation
instructions for the amplifier being used.
Adjust the level of signals output into an amplifier, etc. by
using the OUTPUT LEVEL control.
When the DIGITAL AUDIO OUT (OPTICAL)
terminal of this unit is used (
)
Before using this terminal, remove the terminal’s cover by
pulling it.
Make the connection from this terminal to the digital input
terminal of an amplifier or D/A (digital-to-analog) converter
by using a commercially available optical fiber cable.
Be sure to attach the terminal’s cover when this terminal is
not being used, in order to protect the terminal from dust.
* Use an optical fiber cable that conforms to EIAJ
standards. Other cables might not function correctly.
When this terminal is used for the connection, set the
OUTPUT LEVEL control to maximum.
Choose one of the ways listed below to connect this unit to your amplifier.
Connection cord
(included)
5
IDENTIFICATION OF COMPONENTS
FRONT PANEL
REMOTE CONTROL TRANSMITTER
The control functions on the main unit and on the remote
control transmitter are virtually identical, with the exceptions
described below.
* The PLAY/PAUSE button on the main unit
has both the functions of the PLAY button and
the PAUSE button on the remote control
transmitter.
* Remote control transmitter has two DISC
SKIP buttons. Pressing each button will
search discs in the direction shown by the
arrow.
10
DIMMER
TIME
OPEN/CLOSE
PROG
TAPE
MODE
123
4
56
7890
+
PLAY
PAUSE
SEARCH
STOP
INDEX
OUTPUT LEVEL
+
RANDOM
SKIP
SYNCHRO
REPEAT
DISC SKIP
DISC
SCAN
INDEX button (p. 16)
SYNCHRO
button (p. 21)
OUTPUT LEVEL
buttons (p. 10)
(“+” is identical with “UP
and “–” with “DOWN” of the
OUTPUT LEVEL control
on the main unit.)
DISC SCAN button (p. 9)
DIMMER button (p. 10)
TIME display mode select button (p. 9)
Display panel
Remote control sensor
(p. 22)
POWER switch (p. 7)
Disc tray (p. 7)
OPEN/CLOSE button (p. 7)
DISC SKIP button (p. 7)
STOP button (p. 8)
PLAYXCHANGE
button (p. 7)
PLAY/PAUSE
button (p. 7)
DISC-select buttons (p. 7)
RANDOM
button (p. 11)
PHONES jack (p. 10)
PROG button (p. 12)
SEARCH button (p. 9)
SKIP button (p. 8)
OUTPUT LEVEL button (p. 10)
Disc play MODE select button (p. 7)
POWER
FILE
SAVE
AUTO
DISPLAY OFF
TIME
1234 5
SKIP
SEARCH
+101234567890
PROG TAPE
PLAYXCHANGE
OPEN/CLOSE
PLAY/
PAUSE
STOP
DISC SKIP
FILE/SAVE
MODE
REPEAT
RANDOM
OUTPUT LEVEL
DOWN UP
PHONES
CLEAR
DISC
Numeric buttons (p. 8)
TAPE button (p. 17)
FILE/SAVE button (p. 14)
CLEAR button (p. 13)
PEAK button (p. 20)
REPEAT
button (p. 16)
PEAK
CDC-845
* ( ) indicates the page number on which the control part is best described.
This manual mainly describes how to operate
this unit by using the front panel buttons. To
operate this unit on the remote control
transmitter, use buttons with the same name
as those on the front panel.
REMOTE CONTROL TRANSMITTER
The control functions on the main unit and on the remote
control transmitter are virtually identical, with the exceptions
described below.
* The PLAY/PAUSE button on the main unit
has both the functions of the PLAY button and
the PAUSE button on the remote control
transmitter.
* Remote control transmitter has two DISC
SKIP buttons. Pressing each button will
search discs in the direction shown by the
arrow.
6
OPEN/CLOSE
button (p. 7)
button (p. 7)
DISC SKIP
STOP button (p. 8)
PLAY/PAUSE button (p. 7)
PLAYXCHANGE button (p. 7)
RANDOM button (p. 11)
PHONES jack (p. 10)
REPEAT button (p. 16)
OUTPUT LEVEL button (p. 10)
PROG button (p. 12)
SEARCH button (p. 9)
SKIP button (p. 8)
TIME display mode
select button (p. 9)
Display panel
Remote control sensor (p. 22)
POWER
switch (p. 7)
Disc tray (p. 7)
DISC-select buttons (p. 7)
MODE-select button (p. 7)
POWER
FILE
SAVE
AUTO
DISPLAY OFF
TIME
1 2345
SKIP
SEARCH
+101234567890
PROG TAPE
PLAYXCHANGE
OPEN/CLOSE
PLAY/
PAUSE
STOP
DISC SKIP
FILE/
SAVE
MODE
REPEAT
RANDOM
OUTPUT LEVEL
DOWN UP
PHONES
DISC
Numeric buttons (p. 8)
TAPE button (p. 17)
FILE/SAVE button (p. 14)
PEAK button (p. 20)
PEAK
FRONT PANEL
10
DIMMER
TIME
OPEN/CLOSE
PROG
TAPE
MODE
123
4
56
7890
+
PLAY
PAUSE
SEARCH
STOP
INDEX
OUTPUT LEVEL
+
RANDOM
SKIP
SYNCHRO
REPEAT
DISC SKIP
DISC
SCAN
INDEX button (p. 16)
SYNCHRO
button (p. 21)
OUTPUT LEVEL
buttons (p. 10)
(“+” is identical with “UP
and “–” with “DOWN” of the
OUTPUT LEVEL control
on the main unit.)
DISC SCAN button (p. 9)
DIMMER button (p. 10)
CDC-745
* ( ) indicates the page number on which the control part is best described.
This manual mainly describes how to operate
this unit by using the front panel buttons. To
operate this unit on the remote control
transmitter, use buttons with the same name
as those on the front panel.
7
LOADING DISCS/DISC PLAY
1
2
3
4
5
Select the disc play mode (DISC MODE: SINGLE or
ALL) while watching the display.
“SINGLE” mode: The unit will play a designated disc only.
“ALL” mode: The unit will play all discs in the tray in
sequence.
6
* If necessary, select a desired disc by using a DISC-select
button or the DISC SKIP button.
Notes
After closing the disc tray by pressing the OPEN/CLOSE
button in the stop mode or after selecting any disc by using
the DISC SKIP button, the display shows the total number of
tracks and the total recorded time of the disc to be played for
a few seconds.
Additionally, you can close the disc tray by pressing the
PLAY/PAUSE button, a DISC-select button, a numeric
button or the RANDOM button, or by pressing the front edge
of the disc tray gently. If the tray is closed in these ways,
play will begin automatically, however, the display will not
show the total number of tracks and the total recorded time
of the first disc to be played.
PLAYXCHANGE
During play, you can open the disc tray by pressing the
PLAYXCHANGE button without interrupting disc play.
However, in this case, pressing the DISC SKIP button has no
effect.
1
5 2, 46
3, 6
6
1
6 2, 46
3, 6
5
POWER
OPEN/CLOSE
DISC SKIP
MODE
PLAY/
PAUSE
DISC SKIP
PLAY/
PAUSE
Shows the selected disc
mode.
Label side
upward
Disc tray
Load the fifth disc.
1234 5
DISC
12345
DISC
CDC-845 CDC-745
CDC-845
CDC-745
8
DIRECT PLAY
Select a desired track by using the numeric buttons.
Example: To select track 25
Press
twice, then immediately press
once.
* If a track number higher than the highest track number on the
disc is selected, the last track on the disc will be played.
SKIP PLAY
To play from the beginning of the track following the one
now playing
To play from the beginning of the track now playing
To play from the beginning of the track before the one now
playing
(twice)
* These operations can also be performed when the unit is in
the pause or stop mode.
Display information at disc play
Encloses the tray number of the selected disc.
Shows the tray numbers with discs.
Shows the selected track number.
Shows the time displays. (Refer to “Selecting time
displays” on page 9.)
Displays the numbers that correspond to the numbers of
the tracks (as high as number 15) on the disc. After each
track is played, its corresponding number disappears so the
number of remaining tracks (and their numbers) can be
seen at a glance.
Shows the level of signals output into an amplifier or the
headphone level adjusted by using the OUTPUT LEVEL
control.
To play a desired track on the disc
PLAY/
PAUSE
PAUSE
STOP
1
10
2
34 5 6 78
90
+
SKIP
SKIP
SKIP
➀➁
The selected track
number is displayed.
1
10
2
34 5 6 78
90
+
To stop play temporarily
* To resume play, press the PLAY/PAUSE button again
(or press the PLAY or PAUSE button on the remote control
transmitter).
To stop play completely
9
To advance or reverse play rapidly (MANUAL SEARCH)
To advance rapidly
To reverse rapidly
The sound can be heard (although slightly garbled) during
manual search in either direction. This is convenient for
locating a precise position within a track, or for reviewing the
contents quickly.
Manual search can also be performed while disc play is
paused, though no sound will be heard.
SEARCH
SEARCH
(press and hold)
(press and hold)
When the DISC SCAN button is pressed while this unit is
stopped, this unit will play an early part of each disc in turn.
Each disc is played for 8 seconds.
If, during this play, you hear a disc that you want to listen to in
entirely, press this button once again, or press the PLAY
button on the remote control transmitter. This will cancel this
play mode and the unit will enter into the normal play mode.
Notes
During this play, the disc tray numbers flash on and off on
the display. Every time the play of a disc is finished, the
corresponding tray number is changed from flashing to
lighting.
There may be a case that you can gain no sound with this
play, if the disc has a long blank space between tracks, for
example.
Durng this play, the setting of the disc play mode (MODE),
the program play mode, etc. are canceled temporarily.
Scanning discs to search for a desired disc (or to check discs on the disc tray)
DISC
SCAN
Note
The remaining time
will not be displayed for track number
21 or higher.
Selecting time displays
You can select any of the four time displays by pressing the TIME display mode-select button.
Elapsed time of the track now playing
Remaining time of the track now playing
Total disc play time
Total remaining time on the disc
10
When you listen with headphones
Connect the headphones to the PHONES jack and adjust the
volume by using the OUTPUT LEVEL control.
* Note that the use of the OUTPUT LEVEL control will also
vary the level of the signal output to the amplifier.
When it is not necessary to operate controls inside the control
door, close the door.
To close the door To open the door
Open/close the control door CDC-845
PHONES
OUTPUT LEVEL
DOWN UP
OUTPUT LEVEL
+
or
Changing brightness of the display
You can change the brightness of the display (or turn off the illumination) by pressing the DIMMER button.
During play
Normal illumination
Dim
“OFF”
* While the display illumination is off,
the AUTO DISPLAY OFF indicator
on the front panel illuminates.
Except during play
Normal illumination
Dim
Dim
(The AUTO DISPLAY OFF indicator illuminates.
In this mode, if a disc is played, the display
illumination will be off.)
DIMMER
FILE
SAVE
AUTO
DISPLAY OFF
11
1
2
3 Select whether to play one disc or all discs in the tray.
* If the “SINGLE” disc play mode is selected, next select a
desired disc by using the DISC SKIP button or a DISC-
select button.
4
To cancel random-sequence play
Press the STOP button or RANDOM button once again, or
open the disc tray by pressing the OPEN/CLOSE button.
Notes
This feature will not function during programming, or during
programmed play.
If the POWER is switched off when the random-sequence
play mode is functioning, when the POWER is switched on
again, the unit will begin the random-sequence play
automatically. (This feature is available for timer play.)
If the SKIP button is pressed during random-sequence
play, the next randomly programmed track will be played. If
the SKIP button is pressed, play will return to the
beginning of the track now being played.
This indication appears while the unit is
mixing up tracks.
Total remaining time on the disc will not be displayed during
random-sequence play.
34
2
2
3
4
OPEN/CLOSE
MODE
RANDOM
CDC-845 CDC-745
RANDOM-SEQUENCE PLAY
You can play the tracks in a random sequence (up to 99 tracks). The unit will automatically mix up tracks from all discs or any
desired disc in the disc tray.
12
Shows the program number for the track to be set next.
Shows the selected disc and track number.
Shows the total time of the tracks currently programmed.
Shows only the numbers of programmed tracks on the
selected disc.
* If “P-01” does not appear in the display after the PROG
button is pressed, press the TIME display mode-select
button.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
4
251
3
3
3
4
153
2
PLAY/
PAUSE
➁➂
PROG
DISC SKIP
1
Stop the unit.
2
3
If necessary, select the desired disc.
4
Select the desired track.
5
When the programming is completed;
* Repeat step 3 – 4 to set more programs.
Display information during programming
or
1234 5
DISC
12345
DISC
1
10
2
34 5 6 78
90
+
STOP
CDC-845 CDC-745
CDC-845
CDC-745
PROGRAM PLAY
You can enjoy listening to your favorite tracks selected from one or several discs in any desired order using programmed play.
13
Notes
You can set as many as 40 programs at one time.
You can set a whole disc as a program by pressing “0”,
instead of selecting a track number. At that time, “AL”
flashes in the display.
If you will program tracks from more than one disc, before
you press the PROG button, check the total recorded time of
each disc on the disc tray by pressing the DISC SKIP button
in turn. Without this operation, the total time of the
programmed tracks will not be displayed during
programming.
The total time of the programmed tracks will not be
displayed, if a track number higher than 20 is programmed.
If, during programming, the TIME display mode-select button
is pressed, the program number display can be changed to
display the total time of the programmed tracks or no
information. To return to the previous display, press the
TIME display mode-select button once again.
The SKIP ( and ) button can be used during
playing, but only within the range of the programmed tracks.
The SEARCH ( and ) button can be used during
playing to search through all tracks, including
unprogrammed tracks.
To stop program play
Press the STOP button. The first track number programmed
will be displayed.
To resume play, press the PLAY/PAUSE button. Play will
begin from the beginning of the program.
To cancel a programmed setting
There are several methods, as described below.
Press the STOP button while the unit is stopped.
CDC-845 only
Press the CLEAR button while the unit is stopped.
Open the disc tray.
Switch off the power.
To check programmed data
1. If the unit is in the play mode, press the STOP button.
2. Press the PROG button.
3. Each time the SKIP button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the SKIP button.
To correct programmed data
1. Follow the procedure described in “To check programmed
data”.
2. Display the track number to be corrected by pressing the
SKIP button.
3. Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4. After the correction has been completed, press the PROG
button or PLAY/PAUSE button once again.
14
PROGRAM FILING
This unit has a function that can store (file) program data that has been set. You can play a disc with your favorite program at any
time without setting it again. However, note that you can not file program data which consists of tracks selected from more than one
disc.
To file data of tracks programmed in a desired
order
1 Follow step 1 – 3 on page 12.
2 Select track numbers in a desired order.
* If programs have already been set, make sure that
“TRACK” is flashing continuously in the display. If it is
not, once again press the PROG button. (If a program
play is being performed, press the STOP button, and
then press the PROG button.)
3
Notes
Program data filed in this way can be retained for about two
weeks with the power switched off.
One-program data can be filed for any one disc. If different
program data is filed for a disc, the previous program data
will be deleted from the file, and only the new program data
will be retained in the file.
Program data for a total of as many as about 100 discs can
be filed at any one time.
PROG Numeric buttonsPOWER
CLEAR FILE/SAVE
0
PLAY/PAUSE
DISC
STOP
OPEN/CLOSE
PROGNumeric buttonsPOWER FILE/SAVE
0 PLAY/PAUSE
DISC
STOP
OPEN/CLOSE
CDC-845
CDC-745
FILE
SAVE
AUTO
DISPLAY OFF
FILE
/
SAVE
FILE/SAVE
1
10
2
34 5 6 78
90
+
CDC-845 CDC-745
15
To play with program data
1
2
3 If the FILE indicator is not illuminated in the display,
press the FILE/SAVE button.
4 Select the disc to be played.
Notes
If, in step 4, the SAVE indicator does not illuminate, the disc
does not have its program data in the memory’s file.
To stop the play of the filed program data and change to
ordinary play of the disc, press the FILE/SAVE button. By
this operation, the disc will be played in the ordinary
sequence of tracks, but the program data in the memory’s
file for that disc will not be deleted from the memory. To
once again call out the program data, follow step 3 and 4.
In the “ALL” disc play mode, discs which have program data
in the memory’s file are played with their program data, and
others are played normally.
To delete program data from file
1 If the unit is playing a disc, press the STOP button.
* If a program play is on standby, press the STOP
button (or the CLEAR button for
CDC-845
only)
to cancel that program setting.
2
If the FILE indicator is illuminated in the display, press
the FILE/SAVE button to turn the indicator off.
3 Select the disc of which program you want to delete.
4
5
To delete all program data from the memory’s
file
1 Turn the POWER off.
2
3
4
OPEN/CLOSE
FILE
SAVE
AUTO
DISPLAY OFF
1234 5
DISC
12345
DISC
DISC SKIP
PROG
POWER
0
FILE/SAVE
0
FILE/SAVE
FILE
/
SAVE
0
FILE
/
SAVE
0
(Release.)
The SAVE indicator
goes off.
(Press and hold.)
FILE
/
SAVE
FILE/SAVE
FILE
/
SAVE
FILE/SAVE
CDC-845 CDC-745
CDC-845 CDC-745
CDC-845 CDC-745
CDC-845 CDC-745
CDC-845 CDC-745
16
1 Select a track which has index numbers.
2
3 Select the desired index number.
To cancel the index search function
Press the INDEX button.
Notes
Not all discs have index numbers. The index system is a
method for sub-dividing tracks into smaller divisions (such
as, for example, the movements within classical
symphonies) for easier location of those parts. The liner
notes with the disc usually tell if such index numbers are
included.
If an index number is selected that is higher than any index
number on that disc, play will start from the last index
number point on the disc.
For some discs, play may begin slightly prior to the actual
designated index point.
If the disc has no encoded index points, play will begin from
the start of the selected track.
The index number can be designated only while the INDEX
number display is illuminated.
SINGLE REPEAT (S REP)
A single track is repeatedly played.
* This is also available in the programmed-play mode and the
random-sequence play mode. (If the repeat play mode is
switched off, the programmed-play mode or the random-
sequence play mode will be resumed.)
FULL REPEAT (F REP)
In the “SINGLE” disc play mode: A designated disc is
repeatedly played.
In the “ALL” disc play mode: All discs in the disc tray are
repeatedly played.
* In the programmed-play mode, all programmed tracks are
repeatedly played.
* In the random-sequence play mode, all randomly sequenced
tracks are repeatedly played in the same order.
(OFF)
S REP
FREP
5
5
REPEAT
INDEX
INDEX SEARCH
If the disc includes index numbers, play can be started from any desired index number.
REPEAT PLAY
You can play any desired track or disc (set of discs) repeatedly by pressing the REPEAT button. The repeat play mode will
change whenever you press the REPEAT button.
17
TRACK PROGRAMMING FOR RECORDING TO TAPE
This convenient feature can be used to program tracks for recording to tape. By only memorizing the tape’s total possible recording
time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least amount of
unrecorded space remaining at each end of the tape.
Automatic tape programming
This is for recording tracks on a disc so that they best fit onto a tape.
1 Stop the unit.
2 Select the disc.
3 The peak level searching function of this unit is useful
for adjusting recording level on the tape deck. (Refer
to page 20.)
4 Enter the tape’s total possible recording time.
You can select any of four tape lengths by pressing
the TAPE button.
5 Otherwise, you can also enter the tape’s total possible
recording time manually.
Example: For a C-64 tape (32 minutes on each side)
6
* By pressing the REPEAT button, the unit automatically
programs tracks for side A and side B separately
considering the tape’s total time.
7 Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
8 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY/PAUSE button on
this unit.
Notes
All tracks may not be programmed if the tape’s length is not
enough. To program all tracks, use a longer tape.
In step 6, you can check the program data for side A and
side B.
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
CD synchronized recording method can be used if your tape
deck is compatible with it.
In this case, in step 7 and 8, press the SYNCHRO button
and then press the PLAY button on this unit’s remote control
transmitter. Recording automatically begins.
(For details, refer to page 21.)
5
4 7, 8 1
2
6
7, 8 1
2
645
STOP
1
10
2
34 5 6 78
90
+
TAPE
REPEAT
DISC SKIP
(off)
➀➁
TAPE
CDC-845 CDC-745
18
1 Follow step 1, 4 and 5 on page 17.
2
3 If necessary, select the desired disc.
4 Select the desired track.
5 Repeat step 3–4 to set more programs for side A of
the tape. You can select the same track again.
* If “E rr” appears in the display, the track number just
selected cannot be programmed because there is not
enough time remaining on side A of the tape.
6 After you finish the programming for side A, program
the pause mode by pressing the TAPE button.
* “Pu” flashes in the display, and after then you can begin
programming for side B.
7 Follow step 3–4.
8
Repeat step 3–4 to set more programs for the side B
of the tape. You can select the same track again.
* If “E rr” a ppears in the display, the track number just
selected cannot be programmed because there is not
enough time remaining on side B of the tape.
9
The peak level searching function of this unit is useful
for adjusting recording level on the tape deck. For
peak level searching, when the programming for side
B is finished, press the PROG button and then press
the PEAK button.
10
Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
11
The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording
and, at the same time, press the PLAY/PAUSE
button on this unit.
Notes
If you will program tracks from more than one disc, before
you press the PROG button, check the total recorded time of
each disc on the disc tray by pressing the DISC SKIP button
in turn. Without this operation, the total remaining time of
each side of the tape and previously programmed track
numbers (and also unprogrammed track numbers) will not
be displayed during programming.
In step 5 and 8, even if “E rr” appears in the display, you can
program another track of which time is shorter than the
remaining time on the side of the tape. In this case, you can
check the remaining time on the side of the tape by pressing
the TIME display mode-select button.
CD synchronized recording method can be used if your tape
deck is compatible with it.
In this case, in step 10 and 11, press the SYNCHRO button
and then press the PLAY button on this unit’s remote control
transmitter. Recording automatically begins.
(For details, refer to page 21.)
Notes on tape programming
To check, cancel or correct program data, refer to page 13.
Up to a maximum of 40 tracks can be programmed from
among any or all of the five discs loaded on the disc tray. If,
however, the PAUSE mode is inserted, each PAUSE is
counted as one track.
This function can be used to program up to track number 20.
If the disc has more than 20 tracks, track number 21 and
thereafter will not be programmed.
Manual tape programming
This is for recording desired tracks selected from one or more discs in any desired order onto tape.
6 10, 11
3
2, 9
4
9
10, 11
3
6
2, 9
4
9
1
10
2
34 5 6 78
90
+
TAPE
PROG
DISC SKIP
Flashes on and off.
CDC-845 CDC-745
Random sequential tape programming
The unit will automatically program tracks on a disc in random sequential order for recording to tape.
1 Follow step 1 – 5 on page 17.
2
* The unit will automatically program tracks for side A and
side B separately considering the tape’s total time.
3 Begin recording on the tape deck and press the
PLAY/PAUSE button on this unit at the same time.
4 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY/PAUSE button on
this unit.
Notes
Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining at
the end of the tape also changes accordingly.
If the tape’s length is not enough, all tracks cannot be
programmed. In this case, exchange the tape for a longer one.
In step 2, you can check the program data for side A and
side B.
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
CD synchronized recording method can be used if your tape
deck is compatible with it.
In this case, in step 3 and 4, press the SYNCHRO button
and then press the PLAY button on this unit’s remote control
transmitter. Recording automatically begins.
(For details, refer to page 21.)
Display information during programming
Shows the side of the tape and the program number for the
track to be set next.
Shows the selected disc and track number.
Shows the total remaining time on the side of the tape.
Programmed track numbers illuminate and unprogrammed
ones flash on and off.
* If “A-01” does not appear in the display after the PROG
button is pressed, press the TIME display mode-select
button.
2 3, 4
3, 4
2
➀➁
RANDOM
CDC-845 CDC-745
19
20
CDC-845 CDC-745
This convenient feature automatically searches for the part on a disc where the source level peaks, and next plays the part
repeatedly. For recording to tape, this feature is very helpful to adjust the recording level on the tape deck.
1 Stop the unit.
2 Select the SINGLE disc play mode.
3 Select the disc.
Notes
This feature will also function in the program play mode. If
program play is being performed, first press the STOP
button, and then press the PEAK button. If program play is
not being performed, only press the PEAK button.
To search for the peak level through all discs on the disc
tray, in step 2, select the ALL disc play mode.
4
Searches the disc for the peak level.
Repeatedly plays the part where the source level peaks.
Adjust the recording level on the tape deck listening to
this repeat play.
To cancel this function
Press the STOP button. (Some other buttons can also be
used to cancel this function.)
Even if the peak level searching is performed twice or more
on the same disc, the same part will not be always selected,
because this unit will search for the peak level among parts
on the disc that are randomly selected by the internal
microcomputer.
Automatic searching of the peak level on a disc
STOP
DISC SKIP
0
PEAK
REP
REP
4
1
3
2
3
1
4
2
MODE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Yamaha CDC-745 Manualul proprietarului

Categorie
CD playere
Tip
Manualul proprietarului
Acest manual este potrivit și pentru