Ubiquiti M900 Specificație

Marca: Ubiquiti

Model: M900

Tip: Specificație

Acest manual este potrivit și pentru

Carrier Class

airMAX

™

BaseStation

Models:

M900/M2/M3/M365/M5

Introduction

Thank you for purchasing a Ubiquiti Networks

™

Rocket

™

M series

product. This Quick Start Guide is designed to walk you through

installation and show you how to access the airOS

™

Configuration

Interface.

Package Contents

RocketM Metal Strap 24V PoE Adapter

Carrier Class

airMAX

™

BaseStation

Models:

M900/M2/M3/M365/M5

Power Cord Quick Start Guide

Installation Requirements

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks

™

. For more details, visit www.ubnt.com/toughcable

Rocket

™

M Quick Start Guide

Hardware Overview

Antenna

Connectors

Port Cover

Ethernet Port

USB Port

Note: U.S. product versions are locked to the U.S. Country

Code to ensure compliance with FCC regulations.

Hardware Overview

LEDs

Power The Power LED will light green when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light red when the wireless signal

strength is above -94 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light green when the wireless signal

signal strength is above -73 dBm.

LED will light green when the wireless signal

strength is above -65 dBm.

Rocket

™

M Quick Start Guide

Hardware Installation

1. Remove the Port Cover by lifting the release latch on the

bottom of the RocketM and sliding the Port Cover off.

2. Connect an Ethernet cable to the Ethernet port.

3. Replace the Port Cover.

Hardware Installation

4. Attach the RF Cables to the connectors labeled Chain 0 and

Chain 1 on the RocketM.

5. Attach the RocketM to an antenna. Align the mounting tabs

on the back of the RocketM with the mounting bracket on

the antenna. Slide the RocketM down until it locks into place.

(If you are mounting the RocketM on a pole, refer to the

Pole‑Mounting section on page 7.)

Mounting on a Dish Antenna Mounting on a Sector Antenna

Rocket

™

M Quick Start Guide

6. Attach the RF Cables from the RocketM to the connectors on

the antenna.

Connecting to a Dish Antenna Connecting to a Sector Antenna

7. Attach the Protective Shroud.

Align the arrow on the top of the shroud

with the short hash mark on the Dish

Antenna, and then rotate the shroud

clockwise until it aligns with the long hash

mark to lock it into place.

Slide the Protective Shroud down

over the RocketM until it locks into

place on the Sector Antenna.

Hardware Installation

Pole-Mounting

To mount the RocketM on a pole, use the included Metal Strap and

perform the following steps:

1. Open the Metal Strap by turning the locking mechanism

counter-clockwise. You can loosen it by hand or use a flathead

screwdriver.

2. Straighten out the end of the Metal Strap and slide it through

the back of the RocketM.

Rocket

™

M Quick Start Guide

3. Wrap the Metal Strap around the pole and use a flathead

screwdriver to tighten the locking mechanism by turning it

clockwise.

Connecting Power over Ethernet

1. Connect the other end of the Ethernet cable from the RocketM

to the Ethernet port labeled POE on the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the Ethernet port

labeled LAN on the PoE Adapter.

3. Connect the Power Cord to the power port on the PoE Adapter.

Connect the other end of the Power Cord to a power outlet.

Rocket

™

M Quick Start Guide

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host machine is connected via Ethernet to

the RocketM.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type http://192.168.1.20 in the

address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username and

Password fields. Select your Country and Language. You must

agree to the Terms of Use to use the product. Click Login.

Note: U.S. product versions are locked to the U.S. Country

Code to ensure compliance with FCC regulations.

The airOS Configuration Interface will appear, allowing you to

customize your settings as needed.

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional

installer's responsibility to make sure the device is operated within

local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a variety

of antennas and cables, the Antenna Gain, Cable Loss, and Output

Power fields are provided to the professional installer to assist in

meeting regulatory requirements.

Rocket

™

M Quick Start Guide

Specifications

RocketM

Dimensions 16 x 8 x 3 cm

Weight 0.5 kg

Ports (1) 10/100 Ethernet Port

RF Connectors (2) RPSMA (Waterproof)

Enclosure Outdoor UV Stabilized Plastic

Max. Power Consumption

RocketM9/2/3/365 6.5 W

RocketM5 8 W

Power Supply 24V, 1A PoE Supply Included

Power Method Passive PoE (Pairs 4, 5+; 7,8 Return)

Operating Temperature -30 to 75° C

(-22 to 167° F)

Operating Humidity 5 to 95% Condensing

Shock and Vibrations ETSI300-019-1.4

Operating Frequency

RocketM900 902 - 928 MHz

RocketM2 2402 - 2462 MHz

RocketM3 3370 - 3730 MHz

RocketM365 3650 - 3675 MHz

RocketM5 5170 - 5875 MHz

¹ RocketM3 not supported in the USA

² Only 5725 - 5850 MHz supported in the USA

(USunitswithFCCID:SWX-RM5areallowed5250-5825MHz.)

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be

submerged by water.

WARNING: Avoid using this product during an electrical storm.

There may be a remote risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there are

questions about the installation prior to connecting the equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Rocket

™

M Quick Start Guide

General Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and

warrants that the Products furnished hereunder shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS sole and exclusive obligation under the foregoing

warranty shall be to repair or replace, at its option, any defective Product

that fails during the warranty period. The expense of removal and

reinstallation of any item is not included in this warranty.

The foregoing warranty is exclusive and in lieu of all other warranties,

express or implied, including the implied warranties of merchantability and

fitness for a particular purpose and any warranties arising from a course

of dealing, usage or trade practice with respect to the products. Repair or

replacement in the manner provided herein shall be the sole and exclusive

remedy of Buyer for breach of warranty and shall constitute fulfillment

of all liabilities of UBIQUITI NETWORKS with respect to the quality and

performance of the Products. UBIQUITI NETWORKS reserves the right

to inspect all defective Products (which must be returned by Buyer to

UBIQUITI NETWORKS factory freight prepaid).

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS.

Products returned without an RMA number will not be processed and will

be returned to Buyer freight collect. UBIQUITI NETWORKS shall have no

obligation to make repairs or replacement necessitated by catastrophe,

fault, negligence, misuse, abuse, or accident by Buyer, Buyer’s customers or

any other parties. The warranty period of any repaired or replaced Product

shall not extend beyond its original term.

Warranty Conditions

The foregoing warranty shall apply only if:

(I) The Product has not been subjected to misuse, neglect or unusual

physical, electrical or electromagnetic stress, or some other type of

accident.

(II) No modification, alteration or addition has been made to the Product

by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORK’S

authorized representatives or otherwise approved by UBIQUITI

NETWORKS.

(III) The Product has been properly installed and used at all times in

accordance, and in all material respects, with the applicable Product

documentation.

(IV) All Ethernet cabling runs use CAT5 (or above) shielded cabling.

Compliance

Disclaimer: UBIQUITI NETWORKS does not warrant that the operation of

the products is error-free or that operation will be uninterrupted. In no

event shall UBIQUITI NETWORKS be responsible for damages or claims

of any nature or description relating to system performance, including

coverage, buyer’s selection of products for buyer’s application and/or

failure of products to meet government or regulatory requirements.

Returns

In the unlikely event a defect occurs, please work through the dealer or

distributor from which this product was purchased.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

For MPE and antenna usage details, please visit our website at

www.ubnt.com/products

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

Rocket

™

M Quick Start Guide

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe A est confrome à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 2.52 m from all persons and must not be

located or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d'au moins

2.52 m et ne doivent pas être localisé ou utilisé en conflit avec tout autre

antenne ou transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with

all directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product

and it must follow the CE marking.

Compliance

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt

in Ihrer Verantwortung, dieses Gerät und andere elektrische und

elektronische Geräte über die dafür zuständigen und von der Regierung

oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen.

Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle

negative Folgen für Umwelt und die menschliche Gesundheit zu

vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Español

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este

símbolo en el propio aparato y/o en su embalaje no deben eliminarse

junto con otros residuos urbanos no seleccionados. El símbolo indica

que el producto en cuestión debe separarse de los residuos domésticos

convencionales con vistas a su eliminación. Es responsabilidad suya

desechar este y cualesquiera otros aparatos eléctricos y electrónicos a

través de los puntos de recogida que ponen a su disposición el gobierno y

las autoridades locales. Al desechar y reciclar correctamente estos aparatos

estará contribuyendo a evitar posibles consecuencias negativas para el

medio ambiente y la salud de las personas. Si desea obtener información

más detallada sobre la eliminación segura de su aparato usado, consulte a

las autoridades locales, al servicio de recogida y eliminación de residuos de

su zona o pregunte en la tienda donde adquirió el producto.

Rocket

™

M Quick Start Guide

Français

La directive européenne 2002/96/CE exige que l’équipement sur lequel

est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté

avec les autres ordures ménagères. Ce symbole indique que le produit

doit être éliminé dans un circuit distinct de celui pour les déchets des

ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout

autre matériel électrique ou électronique par les moyens de collecte

indiqués par le gouvernement et les pouvoirs publics des collectivités

territoriales. L’élimination et le recyclage en bonne et due forme ont pour

but de lutter contre l’impact néfaste potentiel de ce type de produits

sur l’environnement et la santé publique. Pour plus d’informations sur le

mode d’élimination de votre ancien équipement, veuillez prendre contact

avec les pouvoirs publics locaux, le service de traitement des déchets, ou

l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2002/96/EC richiede che le apparecchiature

contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non

siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica

che questo prodotto non deve essere smaltito insieme ai normali rifiuti

domestici. È responsabilità del proprietario smaltire sia questi prodotti sia

le altre apparecchiature elettriche ed elettroniche mediante le specifiche

strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il

corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze

potenzialmente negative per l’ambiente e per la salute dell’essere umano.

Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie

apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti

pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel

quale avete acquistato il prodotto.

Pagina se încarcă ...

Ubiquiti M900 Specificație

Marca: Ubiquiti

Model: M900

Tip: Specificație

Acest manual este potrivit și pentru

Descărcați PDF

raport

în alte limbi

English: Ubiquiti M900 Specification
italiano: Ubiquiti M900 specificazione

Ubiquiti M900 Specificație

Acest manual este potrivit și pentru

Ubiquiti M900 Specificație

în alte limbi

Lucrări conexe