Yamaha DVDC996 Manual de utilizare

Marca: Yamaha

Model: DVDC996

Categorie: DVD playere

Tip: Manual de utilizare

DVD-C996

DVD / VIDEO CD / CD PLAYER

LECTEUR DE DVD CHANGEUR

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia V624870

DVD-C996

NATURAL SOUND DVD PLAYER

DIGITAL OUT

DIGITAL

DIGITAL VIDEO

POWER

DVD

VIDEO CD

DISC

2 3 4 5

SKIP

PLAY

CHANGE

DOLBY

00-C996(GB)-cv 8/22/0, 2:51 PM1

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, and clean

place with at least 5 cm above, behind and on the both

sides of this unit - away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

3 Position this unit away from other electrical appliances,

motors and transformers to avoid humming sounds, do

not place this unit where it may get exposed to rain or

any kind of liquid to prevent fire or electrical shock.

4 Avoid extreme temperature swings or excessive use of

humidifier in the room where this unit is installed to

prevent condensation inside this unit, which may cause

an electrical shock, fire, damage to this unit, and/or

personal injury.

5 Do not cover this unit with a newspaper, a tablecloth, a

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit and/or personal injury.

6 Avoid installing is unit in a place where foreign objects

and liquid might fall. It might cause a fire, damage to this

unit and/or personal injury. Do not place the following

objects on this unit:

• Other components, as they may cause damage and/or

discoloration on the surface of this unit.

• Burning objects (i.e., candles), as they may cause fire,

damage to this unit and/or personal injury.

• Containers with liquid in them, as they may cause an

electrical shock to the user and/or damage to this unit.

7 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

8 Do not use force on switches, controls or connection

cables. Never pull the cables when disconnecting them.

9 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may result in fire or other accidents. YAMAHA will not

be held responsible for any damage resulting from the

use of this unit with a voltage other than that specified.

10 Do not attempt to clean this unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

11 Disconnect the power cord from the wall outlet when not

planning to use this unit for a long period of time, or

during an electrical storm, as they may cause damage by

lightning.

12 Do not attempt to modify or fix this unit. Contact the

qualified YAMAHA service personnel when any service is

needed. Cabinet should never be opened for any

reasons.

13 Be sure to read ‘TROUBLESHOOTING’ section

regarding common operating errors before concluding

that this unit is faulty.

DANGER

Visible laser radiation when open. Avoid direct exposure to

beam.

When this unit is plugged to the wall outlet, do not place your

eyes close to the opening of the disc tray and other openings

to look into inside.

Laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

This unit is designed for home use only. Do not use this unit

for business purposes.

Be sure to place this unit on a level surface. If not so, this

unit will fail to work normally at the PLAYXCHANGE

operation and cause damage to the disc(s) and this unit itself.

Caution for moving this unit

• When moving this unit, first remove all discs from the disc

table and close the table by pressing the OPEN/CLOSE

button, and then switch off the power after you confirm that

the front panel display indicates as follows.

Never switch off the power if the front panel display is not

pictured as above, otherwise the unit will break down

during moving because the internal mechanism is not

locked.

• When moving this unit, be sure to first disconnect the

power cord from the AC outlet and disconnect all cords

connecting this unit to other equipment.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured BROWN

must be connected to the terminal which is marked with

the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

2345

002-C996(E)Caution_GB 8/22/0, 3:00 PM2

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

INTRODUCTION

FEATURES

CONTENTS

INTRODUCTION

FEATURES .................................................... 1

GETTING STARTED ................................... 2

Checking the Package Contents ................... 2

Disc Information .......................................... 2

CONTROLS AND FUNCTIONS................. 4

Front Panel/Remote Control ........................ 4

Display ......................................................... 6

PREPARATION

REMOTE CONTROL .................................. 7

Installing Batteries in the Remote Control... 7

Battery Replacement .................................... 7

Using the Remote Control............................ 7

CONNECTIONS ........................................... 8

Notes about Audio Connections ................... 8

Digital Terminals.......................................... 9

Analog Terminals ......................................... 9

Video Terminals ......................................... 10

Remote Control in/out Terminals

[U.S.A. and Canada models] .................. 11

PLAYBACK

BASIC OPERATION .................................. 12

Before Starting Playback............................ 12

Playing a Disc ............................................ 13

Search (to advance or reverse playback

rapidly).................................................... 14

Skipping Chapters / Tracks ........................ 14

Still Picture (to pause playback) ................ 15

Frame Advance / Reverse ........................... 15

Slow-Motion Play ...................................... 15

SELECTING PLAY MODES..................... 16

Repeat Play................................................. 16

A-B Repeat................................................. 17

Random-Sequence Play [VCD] [CD] ........ 17

Program Play [VCD] [CD]......................... 18

ADVANCED FEATURES........................... 19

Menu Screen [DVD] .................................. 19

Playback Control [VCD]............................ 19

Switching Audio Tracks [DVD] [VCD]..... 20

Switching Subtitle Tracks [DVD] .............. 21

Switching Camera Angles .......................... 21

ON-SCREEN MENU .................................. 22

Operating On-Screen Menu ....................... 22

Disc Information Screen ............................ 23

Player’s Information Screen ....................... 24

Shuttle Screen............................................. 24

SETUP MENU

SETUP MENU ............................................. 25

Operating the Setup Menu ......................... 25

DESCRIPTION OF EACH ITEM............. 26

1.Disc Language [DVD] ............................ 26

2.Ratings [DVD] ........................................ 27

3.Menu Language ...................................... 28

4.On-Screen Massages............................... 28

5.FL Display .............................................. 28

6.TV Aspect ............................................... 28

7.Digital Audio Output .............................. 29

9.Other Settings ......................................... 30

APPENDIX

TROUBLESHOOTING.............................. 31

GLOSSARY ................................................. 33

LANGUAGE CODE LIST ......................... 33

SPECIFICATIONS ..................................... 34

● 5-Disc Auto-changer for playing DVD-Video, audio CD

and Video CD

● PLAYXCHANGE; Disc Changing Capability while

playing another

● 1 OPTICAL and 1 COAXIAL Digital Outputs for Dolby

Digital, DTS, MPEG and Linear PCM

● 96 kHz, 24 Bit Audio DAC for high sound quality

● Compatible with almost all features of DVD discs

(Multi-angle, Multi-language, Parental control, etc.)

● Easy Operation through On-screen Menu (Graphical

User Interface)

● Multi-speed Playback Capability

● Component Video [U.S.A, Canada, Australia and

General models], S-Video Outputs for high picture

quality

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

DOLBY

DIGITAL

101-C996(E)01 7/31/0, 4:15 PM1

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

Batteries (AA, R06, UM-3) RCA pin cable (audio/video)

Disc Information

This DVD changer is designed for use with following types of disc only. Never attempt to load any other type of disc into this

unit because it may damage this unit.

Notes

• This unit is not compatible with CD-R, CD-RW, Photo-CD, CD-ROM, DVD-Audio, DVD-ROM, DVD-RAM, SVCD, CDV, etc.

• Do not use any non standard shaped discs (heart, etc.).

• Do not use disc with tape, seals, or paste on it, damage to the unit may result.

• To reproduce DTS sound, it is necessary to connect a DTS decoder to this unit.

• Some DVD and VCD features described in this manual may not be available or may operate in a different way because they are subject to

software producer’s design. Check each disc’s instruction.

Example:

‘ ’ appears when you press the skip buttons to move to the next section.

Type of disc DVD-Video

8 cm disc/12 cm disc

Video CD

8 cm disc/12 cm disc

Audio CD

8 cm disc/12 cm disc

Mark printed on the disc

DIGITAL VIDEO

102-C996(E)02-06 7/31/0, 4:15 PM2

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

GETTING STARTED

■ Region management information

DVD

This DVD player is designed to meet DVD standard that supports region management system. Check the regional code

number marked on the disc packages. If the number does not match this unit’s region number (see the below table or the back

of this unit), this unit refuses to play that disc.

■ Notes about handling discs

• Hold discs by touching only the edges or center hole.

• When a disc is not currently being loaded on the disc

tray, store it in an appropriate case.

• Playback of discs is generally not affected by small

particles of dust or fingerprints on their playing surface.

Even so, they should be kept clean. Wipe by using a

clean, dry cloth. Do not wipe with a circular motion;

wipe straight outward from the center.

Model Region number of this unit Discs can be played

U.S.A. and Canada models

1 1

ALL

or a mark which includes

the region number ‘1’.

Europe and U.K. models

2 2

ALL

or a mark which includes

the region number ‘2’.

General model

3 3

ALL

or a mark which includes

the region number ‘3’.

Australia model

4 4

ALL

or a mark which includes

the region number ‘4’.

• Do not try to clean the disc’s surface by using any type

of disc cleaner, record spray, anti-static spray or liquid,

or any other chemical-based liquid, because such

substances might irreparably damage the disc’s surface.

• Do not expose discs to direct sunlight, high temperature

or high humidity for a long period of time, because these

might warp or otherwise damage the disc.

No!

102-C996(E)02-06 7/31/0, 4:15 PM3

CONTROLS AND FUNCTIONS

Front Panel/Remote Control

Front Panel

NATURAL SOUND DVD PLAYER

DIGITAL OUT

DIGITAL

DOLBY

DIGITAL VIDEO

POWER

DVD

VIDEO CD

DISC

1 2 3 4 5

SKIP

PLAY

CHANGE

231

45678

Remote Control

1 POWER (p.13)

Press to turn the power on and off.

2 Disc tray (p.13)

Up to 5 discs can be loaded on this tray.

3 open/close(OPEN/CLOSE) (p.13)

Press to open and close the disc tray.

4 Display panel

See p.6.

5 DISC (1,2,3,4,5) (p.13)

Press to play the disc loaded on the guide of the correspond-

ing number.

6 e,r (SEARCH) (p.14)

Use to advance or reverse playback rapidly.

7 t,y (SKIP) (p.14)

y: Press to skip to the beginning of the next chapter

(track).

t: Press to skip to the beginning of the currently played

chapter (track).

8 w (PLAY) (p.13)

Press to start playback.

9 d (PAUSE) (p.15)

Press to pause.

0 a (STOP) (p.13)

Press to stop playback.

q PLAYXCHANGE (p.14)

Press to open and close the disc tray during playback. You

can exchange discs other than the one being played.

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

102-C996(E)02-06 7/31/0, 4:15 PM4

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

w REPEAT (p.16)

Press to repeat playback of a title, chapter, track, etc.

e A-B (p.17)

Press to specify two points and to repeat playback between

them.

r Numeric buttons

Use to select a title, chapter, track, etc.

t ANGLE

Press to change angles when the scene of the disc being

played contains two or more angles.

y Cursor buttons, ENTER

Use to select and determine an item on menu screen,etc.

u AUDIO (p.20)

Press to change audio track language and/or format when

the disc being played contains two or more different audio

tracks.

i TOP MENU

Press to go to the initial screen when operating in the menu

screen.

CONTROLS AND FUNCTIONS

o SETUP (p.25)

Press to call up SETUP MENU screen.

p DISC SKIP

Press to select another disc.

a PLAY MODE (p.17, 18)

Press to switch among random play, program play, and

normal play.

s RETURN (p.25)

Press to go back to the previous screen when operating in

the menu screen.

d SUBTITLE (p.21)

Press to change subtitles when the disc being played

contains several subtitles.

f MENU (p.19)

Press to call up menu screen contained in the disc.

g ON SCREEN (p.22)

Press to turn the on-screen menu (GUI icons) on and off on

the video monitor.

h CANCEL

Press to cancel a specific mode or a setting.

102-C996(E)02-06 7/31/0, 4:15 PM5

Display

CONTROLS AND FUNCTIONS

1 VCD

VCD lights up when a Video CD is selected and CD lights

up when a CD is selected.

2 DVD

Lights up when a DVD is selected.

3 RNDM

Lights up during random-sequence play.

4 PROG

Lights up during program play.

5 ANGLE

Lights up when the scene currently played contains different

angle(s).

6 Repeat mode indicator

• T and REP light up when repeating a title or a track.

• C and REP light up when repeating a chapter.

• REP and A-B light up when repeating between the two

points you have specified.

• REP and DISC 1 light up when repeating the currently

selected disc.

• REP and DISC 5 light up when repeating all the discs

loaded on the disc tray.

7 MPEG

DVD

Lights up when an audio track encoded with MPEG format

is selected.

8 PCM

DVD

Lights up when an audio track encoded with Linear PCM

format is selected.

9 q Digital

DVD

Lights up when an audio track encoded with Dolby digital

format is selected.

0 t

DVD

Lights up when an audio track encoded with DTS format is

selected.

q w

Lights up during playback.

w d

Lights up while playback is paused.

1 2 3 4 5

One of these numbers lights up to show the currently

selected disc, which is loaded on the guide of the corre-

sponding number.

r Multi-information display

Shows various information such as title, chapter or track

number, elapsed playing time etc.

DVD

VCD

PROG

RNDM

TC REP A

–

B DISC 15

ANGLE MPEG PCM

Digital

1 2 3 4 5

12 34 567 8 9 0 q w

102-C996(E)02-06 7/31/0, 4:15 PM6

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

PREPARATION

REMOTE CONTROL

Installing Batteries in the Remote Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AA, R06, UM-3 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the unit, the batteries are weak. Replace all the batteries with new ones.

Notes

• Use only AA, R06 or UM-3 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside the battery compartment.)

• Remove the batteries if the remote control will not be used for an extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

NATURAL SOUND DVD PLAYER

DIGITAL OUT

DIGITAL

DOLBY

DIGITAL VIDEO

POWER

DVD

VIDEO CD

DISC

2 3 4 5

SKIP

PLAY

CHANGE

30°

Remote control

sensor

Within approximately 6 m

(20 feet)

103-C996(E)07-11 7/31/0, 4:15 PM7

CONNECTIONS

CAUTION

• Never connect this unit and other equipment to power supply until all connections have been completed.

Be sure all connections are made correctly, observing the color-coding of terminals of both this unit and the equipment to be

connected. Also refer to the instructions of the equipment to be connected.

REMOTE

CONTROL

OUT IN

COMPONENT

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

[U.S.A model]

Remote Control in /out terminals

[U.S.A. model] (^p.11)

Video terminals (^p.12)

Analog terminals (^p.9)

• For connecting a stereo amplifier,

etc.

Digital terminals (^p.9)

• Connect an AV amplifier with

built-in decoder to these

terminals to enjoy theater-like

surround sound.

To AC outlet

• After completing all

connections, connect

the AC power code to

an AC power outlet.

Notes about Audio Connections

Select the correct output format at ‘7 Digital Audio Output’ on the SETUP MENU in accordance with your AV system.

* Select ‘No’ when the connected equipment has 96-kHz/24-bit D/A converter to enjoy high-fidelity audio. However, no

digital signal is output if the disc you play is copyright-protected.

** No signal is output from this unit’s digital audio output terminal.

*** Multi-channel signals are downmixed to 2-channels Linear PCM and then output from both digital and analog output

terminals.

• See p.29 for further information.

AV amplifier with digital input(s) and

Dolby Digital/ MPEG*1 decoder

(without DTS decoder)

Equipment to be connected Appropriate settings at ‘7 Digital Audio Output’

1. PCM Down

Conversion*

2. Dolby Digial 3. DTS Digial

Surround

4. MPEG (Europe,

U.K. and Australia

models)

AV amplifier with digital input(s) and

Dolby Digital/DTS/MPEG decoder

Yes Bitstream Bitstream Bitstream

Yes Bitstream Off** Bitstream

AV amplifier with Dolby Prologic

decoder

Yes PCM*** Off** PCM***

Stereo amplifier without digital input No PCM*** Off** PCM***

103-C996(E)07-11 7/31/0, 4:15 PM8

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

Digital Terminals

This unit has COAXIAL and OPTICAL digital output

terminals. Connect one or both of them to your AV amplifier

equipped with Dolby digital, DTS, or MPEG decoder using

each specific cable (separate purchase).

COMPONENT

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

COAXIAL

OPTICAL

AV amplifier

Left main

speaker

Center speaker

Right main

speaker

Subwoofer

Left rear

speaker

Right rear

speaker

■ When connecting the optical fiber

cable

• Remove the cover when using the OPTICAL terminal.

Keep the cover and attach it when the terminal is not

being used to protect it from dust.

• Bend an optical cable as little as possible.

• Use commercially available optical fiber cable that

conforms to EIA standards. Other cables may not

function correctly.

Analog Terminals

Connect AUDIO OUT L (left) and R (right) terminals of

this unit to corresponding input terminals of your audio

equipment such as stereo amplifier.

If the audio equipment does not have subwoofer output, you

can use this unit’s SUBWOOFER terminal to connect your

subwoofer system (subwoofer with built-in amplifier). In

that case, set the ‘subwoofer’ item on the on-screen menu to

‘ON’ (^p.24).

COMPONENT

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

CD/DVD

R L

AUDIO INPUT

Amplifier

Subwoofer

system

CONNECTIONS

[U.S.A. model]

103-C996(E)07-11 7/31/0, 4:15 PM9

Video Terminals

If your AV amplifier has video output terminals, connect

your amplifier (and then to your video monitor) so that you

can use one video monitor for several different video

sources (LD, VCR etc.) by simply switching the input

source selector of your amplifier.

This unit has three types of video output terminals. Use one

of them in accordance with the input terminals of the

equipment to be connected.

Note

• Do not connect this unit to a video monitor through a video

cassette recorder. If you do so, the picture may not be played back

properly due to the copyright protection technology incorporated

in this unit.

■ Component Video terminal <A>

U.S.A, Canada, Australia and General models

Component video connection achieves high fidelity in

reproducing colors (better performance than S-video

connection), separating video signal into luminance (Y,

terminal color-coded as green), and color difference (P

blue/P

R, red). Use commercially available coaxial cables.

Amplifier (and Video monitor) with component input is

required. Observe the color of each terminal when connect-

ing. If your amplifier does not have component output

terminals, connecting this unit’s component output directly

to your video monitor’s component input can reproduce

better video image.

Note

• Do not connect this unit’s COMPONENT VIDEO OUT terminals

to component video input terminals special for HD (High-

Definition) TV.

■ S-Video terminal <B>

S (separate) video connection achieves a clearer picture than

composite video connection by separating color and

luminance when transmitting signals. Use commercially

available S-video cable. Amplifier (and Video monitor) with

S-video input is required.

■ Composite Video terminal (1, 2) <C>

Use RCA video cable supplied with this unit when

connecting this unit to a video monitor.

VIDEO 1, 2 terminals of VIDEO OUT output the same

signal. You can connect one to your amplifier’s input using

supplied RCA cable, and the other to another amplifier or a

video monitor.

CONNECTIONS

COMPONENT

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

COMPONENT

VIDEO IN

S VIDEO

INPUT

VIDEO

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

S VIDEO

OUT

S VIDEO

VIDEO

OUT

VIDEO

Amplifier

Video monitor

[U.S.A. model]

103-C996(E)07-11 7/31/0, 4:15 PM10

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

■ 21-pin SCART terminal

U.K. and Europe models

If your video monitor has only 21-pin terminal for video

input, and you want to connect it directly to this unit, you

can use this unit’s 21-pin SCART output terminal (this

terminal does not output RGB component signals).

CONNECTIONS

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

21191715131197531

18161412108642

Remote Control in/out Terminals

[U.S.A. and Canada models]

These terminals are used for custom installation system that

transmits remote control signals via cables. Connect this

unit’s REMOTE CONTROL IN to the Remote control

output of the control unit of your system.

By connecting this unit’s REMOTE CONTROL OUT to

another piece of equipment’s Remote control input terminal,

you can also operate that equipment with the system remote

control.

REMOTE

CONTROL

OUT IN

COMPONENT

VIDEO OUT

VIDEO

S VIDEO

AUDIO

OUT

SUB

WOOFER

DTS

COAXIAL OPTICAL

PCM/ DIGITAL

(Pin no.2, 5 to7, 9 to 12, 20: no connection)

• You can select ‘Video’ or ‘S-Video’ at the ‘6 AV Output’

on the setup menu ‘9.Other settings’. See p.30.

Pin no. Video S video

1 Audio output (R) Audio output (R)

3 Audio output (L) Audio output (L)

4 Audio GND Audio GND

8 Switching voltage Switching voltage

13 No connection S video (C) output GND

14 Blanking GND Blanking GND

15 No connection S video (C) output

16 Blanking Blanking

17 Video output GND S video (Y) output GND

18 Video input GND Video input GND

19 Video output S video (Y) output

21 GND GND

[U. K. model]

[U.S.A. model]

103-C996(E)07-11 7/31/0, 4:15 PM11

PLAYBACK

BASIC OPERATION

Before Starting Playback

To play a disc properly, you need to adjust the formats of audio and video signals output from this unit in accordance with the

equipment connected to this unit. See p.25 to 30 for more detailed information.

CAUTION

• Be sure to select the appropriate positions at ‘7 Digital Audio Output’ on the SETUP MENU. Otherwise, there may be

a case where digital signal which the connected equipment cannot process will be output and its noise could damage

your ears and your speakers.

■ 6 TV Aspect

■ 7 Digital Audio Output

• To output digital signal

from this unit

Type of the connected video monitor Appropriate setting

Conventional type 1. 4:3

Widescreen type 2. 16:9

Notes

• When you select ‘No’ at 1. PCM Down Conversion, digital signal may not be output

depending on the disc you play.

• Make sure to connect digital terminals of both this unit and the audio equipment as

instructed on page 9.

• To output analog signal

from this unit

The connected audio

equipment has

Corresponding item Appropriate setting

96-kHz/24-bit D/A converter 1. PCM Down

Conversion

Dolby Digital decoder 2. Dolby Digital Bitstream

DTS decoder 3. DTS Bitstream

MPEG decoder 4. MPEG [Europe and

U.K. models only]

Bitstream

• Adjust some other settings such as on-screen display language, ratings, etc. as necessary. See SETUP MENU (p.25 to 30)

for detail.

Item in ‘7 Digital Audio Output’ Appropriate setting

1. PCM Down Conversion No

2. Dolby Digital PCM

3. DTS Off

4. MPEG [Europe and U.K. models only] PCM

104-C996(E)12-21 7/31/0, 4:15 PM12

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

Playing a Disc

■ Preparation

Select DVD as the input source on your AV amplifier.

1 Press POWER to turn the power on.

2 Press OPEN/CLOSE (or v) to open the disc

tray.

3 Load discs.

Use the disc guides (numbered, 1 to 5) to align the

discs correctly.

4 Press w (PLAY).

The disc tray closes and playback starts. This unit plays

all discs on the tray in sequence.

• If necessary, select a desired disc using DISC SKIP or one of the

DISC (1, 2, 3, 4 or 5) buttons.

• When a menu screen appears:

DVD

See ‘Menu Screen’ in p.19.

VCD

See ‘Playback Control’ in p.19.

Note

• When this unit finishes playing a DVD, this unit stops playback or

shows the menu screen and does not start playing the next disc.

■ To stop playback

Press a (STOP).

Resume function

This unit memorizes where a (STOP) was pressed (W

indicator flashes on the display). When you press w (PLAY)

in this status, playback resumes from where it was stopped.

To clear the memory, press a (STOP) once more so that the

W indicator goes off.

Notes

• This function may not work with some discs or on some part of

a disc.

• If you turn the power off, resume function is cleared.

Chapter review function [DVD]

This function plays the first few seconds of each chapter

from the beginning of the title up to where the operation

was stopped before starting normal playback so that you can

review previous chapters.

1 Press w (PLAY) while the message as illustrated on the

left is displayed on the screen.

2 Press w (PLAY) again while the message is displayed on

the screen.

Notes

• This function may not work with some DVDs.

• Canceling resume function will also clear the chapter review

function.

BASIC OPERATION

NATURAL SOUND DVD PLAYER

DIGITAL OUT

DIGITAL

DOLBY

DIGITAL VIDEO

POWER

DVD

VIDEO CD

DISC

2 3 4 5

SKIP

PLAY

CHANGE

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

ANGLE RETURN

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

DISC

(1, 2, 3, 4, 5),

DISC SKIP

Label side

upward

Disc tray

4 (PLAY)

STOP

4 (PLAY)

STOP

U.S.A., Canada and General models

Europe, U.K. and Australia models

Press PLAY to Chapter Preview

Press PLAY to Chapter Review

104-C996(E)13 8/22/0, 2:40 PM13

■ After operation

When this unit is not in use, remove discs and press

POWER.

■ To select a specific disc

Press DISC (1, 2, 3, 4 or 5).

Playxchange

By pressing PLAYXCHANGE, you can open the disc tray

and load or replace discs without interrupting play.

However, never load a disc on the guide half hidden

inside the unit because the disc currently being played is

to be placed there.

Search (to advance or reverse playback rapidly)

Press SEARCH r (or e) to search forward (or back-

ward) during playback.

• To return to normal play, press w (PLAY).

• Pressing the button repeatedly increases searching speed.

BASIC OPERATION

CANCEL

DISC

2 3 4 5

SKIP

PLAY

CHANGE

PLAY

SEARCH PLAY

Skipping Chapters / Tracks

Press SKIP y to skip forward or t to skip backward.

Press once for each chapter (track) to be skipped.

Note

• When playing a VCD with playback control, skip operation may

not function as described above.

■ To select a specific track

VCD

Enter a desired track number using numeric buttons.

To select a two-digit number, press [

10] and then enter the

upper figure and the last figure succesively.

Example (to select track 17):

1 Press [

10]

2 Press [1].

3 Press [7].

DVD

VIDEO CD

DISC

2 3 4 5

SKIP

PLAY

CHANGE

SKIP

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

TOP MENU

SETUP

ON SCREEN

CANCEL

Numeric

buttons

SKIP

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

1 2 3

DISC

2 3 4 5

SKIP

PLAY

CHANGE

DISC

(1, 2, 3, 4, 5)

DISC

(1, 2, 3, 4, 5)

PLAYXCHANGE

104-C996(E)12-21 7/31/0, 4:16 PM14

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

Still Picture (to pause playback)

Press d (PAUSE).

• To resume play, press w (PLAY).

CANCEL

DISC

2 3 4 5

SKIP

PLAY

CHANGE

PAUSE

Frame Advance / Reverse

DVD

VCD

1 Press d (PAUSE) during playback.

2 Press the cursor buttons [ , ].

Each press advances (or reverses) still picture by one frame.

• To return to normal play, press w (PLAY).

ANGLE RETURN

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

PLAY

Slow-Motion Play

DVD

VCD

1 Press d (PAUSE) during playback.

2 Press [e, r].

• To return to normal play, press w (PLAY).

• Pressing the button repeatedly increases the speed.

CANCEL

DISC

2 3 4 5

SKIP

PLAY

CHANGE

2 1

PLAY

BASIC OPERATION

104-C996(E)12-21 7/31/0, 4:16 PM15

SELECTING PLAY MODES

Repeat Play

This function allows you to play your desired chapter, track

or disc repeatedly.

■ Press [REPEAT] during playback.

Each time this button is pressed, repeat mode changes

as follows. The name of the selected repeat mode

scrolls once on the multi-information display and the

corresponding indicators light up.

DVD

a CHAPTER REPEAT: The current chapter is played

repeatedly.

b TITLE REPEAT: The current title is played repeatedly.

c ALL REPEAT: All the discs loaded on the tray (DVD,

VCD or CD) are played repeatedly.

d REPEAT OFF: Repeat play mode is canceled.

VCD

e TRACK REPEAT: The current track is played repeat-

edly.

f DISC REPEAT: The current disc is played repeatedly.

g ALL REPEAT: All the discs loaded on the tray (DVD,

VCD or CD) are played repeatedly.

h REPEAT OFF: Repeat play mode is canceled.

Pressing [REPEAT] while playback is stopped switches

‘ALL REPEAT’ to ‘REPEAT OFF’ or vice versa.

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

REPEAT

C REP

T REP

REP DISC 5

T REP

REP DISC 1

REP DISC 5

RNDM

T REP

RNDM

REP

RNDM

‘REP’ goes off. ‘REP’ goes off.

■ Program repeat

VCD

If REPEAT is pressed during program play (p.18), repeat

mode changes as follows.

i 1 STEP REPEAT: Repeating the track being played

j ALL REPEAT: Repeating all the programmed tracks

k REPEAT OFF: Canceling repeat mode (go back to

normal program play)

■ Random-sequence repeat

VCD

If REPEAT is pressed during random-sequence play (p.17),

repeat mode changes as follows.

l TRACK REPEAT: Repeating the track being played

m ALL REPEAT: Playing all the tracks repeatedly, each

time in different random-sequence.

n REPEAT OFF: Canceling repeat mode (go back to

normal random-sequence play)

Notes

• Repeat play may not work properly with some DVDs.

• Repeat play does not work with an interactive DVD or during

menu play of a VCD with playback control.

PROG

REP 1

PROG

REP

PROG

Program repeat Random-sequence repeat

104-C996(E)12-21 7/31/0, 4:16 PM16

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU APPENDIX English

A-B Repeat

This function allows you to specify two points and play

between them repeatedly.

1 Press A-B during play at the point where you

want to start A-B repeat.

‘REP’ and ‘A-’ light up and ‘B’ flashes on the display.

2 Press A-B at the point where you want to end

A-B repeat.

REP A-B appears on the display and repeat play of the

section between point A and B starts.

■ To cancel A-B repeat

Press A-B repeatedly until A-B indicator on the display goes

off.

Notes

• This function may not available with some DVDs.

• This function works only within a title (DVD) or a track (VCD,

CD).

SELECTING PLAY MODES

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

A–B

REP A

–

REP A

–

Lights up Flashes

Lights up

Random-Sequence Play [VCD] [CD]

When you select this mode, this unit plays all tracks on all

CDs and/or Video CDs loaded on the disc tray in random

sequence.

1 Press PLAY MODE once or more while play-

back is stopped.

RNDM indicator lights up on the display.

2 Press w (PLAY) to start random-sequence play.

■ To cancel random-sequence mode

Press a (STOP) twice during play.

Random-sequence play is suspended.

2 Press PLAY MODE once.

RNDM indicator goes off.

If you press w (PLAY) succesively, normal playback starts

from the beginning of the disc having been played before

canceling random-sequence mode.

Opening the disc tray also cancels this mode.

Note

When this unit is in random-sequence mode while a Video CD

(ver.2.0) is loaded, playback control is canceled during random-

sequence playback.

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

ANGLE RETURN

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

RNDM

Lights up

STOP

104-C996(E)12-21 7/31/0, 4:16 PM17

Program Play [VCD] [CD]

You can enjoy listening to your favorite tracks selected from

one or more discs in any desired order by programming

tracks.

1 Press PLAY MODE once or more while play-

back is stopped.

The display shows the step information.

• To exit programming mode, press PLAY MODE

twice.

2 Press DISC (1-5) to select the disc.

3 Press numeric buttons to select the track.

• Repeat step 2 and 3 to program other tracks in your

desired order.

• See p.14 about how to enter the track with numeric

buttons.

• To program a whole disc, press ENTER (‘ALL’

appears on the display).

• Pressing a (STOP) cancels all tracks programmed

so far.

You can program up to 32 tracks to be played in desired

order.

4 Press w (PLAY) to start program play.

■ To cancel the programmed tracks

Press the cursor buttons ( , ) to select the track you

want to cancel.

2 Press CANCEL.

Opening the disc tray also cancels this mode.

Note

When you program a track of a Video CD (ver.2.0), playback

control is canceled during program play.

SELECTING PLAY MODES

OPEN/

DISC1 DISC2 DISC3

DISC4 DISC5 DISC SKIP

REPEAT A–B

PLAY MODE

ANGLE RETURN

1 2 3

4 5 6

7 8 9

ANGLE RETURN

ENTER

AUDIO

SUBTITLE

TOP MENU

SETUP

ON SCREEN

CANCEL

ENTER

Cursor buttons

(

, )

PROG

Disc No. Program No.

Disc No. track No. Program No.

STOP

104-C996(E)12-21 7/31/0, 4:16 PM18

Pagina se încarcă ...

Yamaha DVDC996 Manual de utilizare

Marca: Yamaha

Model: DVDC996

Categorie: DVD playere

Tip: Manual de utilizare

Descărcați PDF

raport

în alte limbi

Türkçe: Yamaha DVDC996 Kullanım kılavuzu
français: Yamaha DVDC996 Manuel utilisateur
čeština: Yamaha DVDC996 Uživatelský manuál
русский: Yamaha DVDC996 Руководство пользователя
English: Yamaha DVDC996 User manual
suomi: Yamaha DVDC996 Ohjekirja
polski: Yamaha DVDC996 Instrukcja obsługi
Deutsch: Yamaha DVDC996 Benutzerhandbuch
italiano: Yamaha DVDC996 Manuale utente
español: Yamaha DVDC996 Manual de usuario
svenska: Yamaha DVDC996 Användarmanual
dansk: Yamaha DVDC996 Brugermanual
português: Yamaha DVDC996 Manual do usuário
Nederlands: Yamaha DVDC996 Handleiding

Yamaha DVDC996 Manual de utilizare

Yamaha DVDC996 Manual de utilizare

în alte limbi

Lucrări conexe