Whirlpool AKR 798 IX Manualul utilizatorului

Whirlpool
Marca
Whirlpool
Model
AKR 798 IX
Categorie
Hote pentru aragaz
Tip
Manualul utilizatorului
5019 318 33313
INSTALLATION UND GEBRAUCH
Der Mindestabstand zwischen dem Kochfeld und der unteren Kante der Dunstabzugshaube MUSS bei
Elektroplatten 50 cm und bei Gas- oder kombinierten Herden 65 cm betragen. Überprüfen Sie vor der
Installation auch die im Handbuch des Kochfeldes angegebenen Abstände.
Die Installation der Abzugshaube muss von einer Fachkraft ausgeführt werden.
Schließen Sie das Gerät erst nach seiner kompletten Installation an das Stromnetz an.
WARNUNG: Aufgrund des schweren Gewichtes sind mindestens zwei oder noch mehr Personen zur
Beförderung und Installation der Dunstabzugshaube erforderlich.
Hinweise zu Installation und Gebrauch: Lesen Sie vor dem Gebrauch der Dunstabzugshaube die vorliegende
Gebrauchsanweisung aufmerksam durch. Der Hersteller lehnt jede Haftung für Störungen, Schäden oder Feuer
ab, die bei Missachtung der vorliegenden Gebrauchsanweisungen durch das Gerät entstehen sollten.
INSTALLATION AND USE
The minimum distance between the support surface of the recipients on the cooking device and the lowest part
of the hood MUST NOT BE less than 50 cm in the case of electric cookers and 65 cm for gas or combination
cookers. Before installation, moreover, check the distances specified in the hob's user manual.
Hood installation must be carried out by a qualified technician.
Do not connect the appliance to the mains power supply until installation has been completed.
WARNING: Very heavy product; hood handling and installation must be carried out by at least two persons.
Note on installation and use: Read this manual carefully before installing or using the hood. The Manufacturer
declines any liability for problems, fires or damage caused to the appliance due to non-compliance with the
instructions given in this manual.
MONTAGE ET UTILISATION
La distance minimum entre la surface de support des récipients sur le dispositif de cuisson et la partie la plus basse
de la hotte NE DOIT PAS ÊTRE inférieure à 50 cm pour les cuisinières électriques et à 65 cm pour les cuisinières
à gaz ou mixtes. Avant l’installation, il convient de vérifier les distances indiquées dans le manuel de la table de
cuisson.
L’installation de la hotte doit être confiée à un technicien qualifié.
Ne branchez pas l’appareil tant que l’installation n’est pas terminée.
AVERTISSEMENT : Appareil excessivement lourd ; la manutention et l’installation de la hotte doivent être
effectuées par deux personnes ou plus.
Remarque pour le montage et l’utilisation : Avant de monter ou d’utiliser la hotte, lisez attentivement ce
manuel. Le fabricant décline toute responsabilité en cas d’inconvénients, dommages ou incendies provoqués par
l’appareil et dus à la non-observation des instructions contenues dans cette notice.
INSTALLATIE EN GEBRUIK
De minimale afstand tussen het steunoppervlak van de pannen op het kooktoestel en het laagste deel van de
afzuigkap MAG NIET MINDER ZIJN dan 50 cm bij elektrische kooktoestellen en 65 cm bij kooktoestellen op gas
of gemengd. Controleer bovendien de afstanden die in de handleiding van de kookplaat zijn vermeld, voordat u
de kap installeert.
De installatie van de afzuigkap moet worden uitgevoerd door een gekwalificeerd technicus.
Sluit het apparaat niet op het elektriciteitsnet aan alvorens de installatie voltooid is.
WAARSCHUWING: Aangezien dit apparaat zwaar is, dient het door minstens twee of meer personen
verplaatst en geïnstalleerd te worden.
Opmerking voor installatie en gebruik: Lees voordat u de afzuigkap installeert of gebruikt deze handleiding
zorgvuldig door. De fabrikant aanvaardt geen enkele verantwoordelijkheid voor problemen, schade of brand die
veroorzaakt is door het niet naleven van de instructies in deze handleiding.
D
GB
F
NL
5019 318 33313
INSTALACIÓN Y UTILIZACIÓN
La distancia mínima entre la superficie de apoyo de los recipientes en la placa de cocción y la parte más baja de
la campana NO DEBE SER INFERIOR a 50 cm en caso de cocinas eléctricas y 65 cm en caso de cocinas a gas o
mixtas. Antes de la instalación, verifique las distancias indicadas en el manual de la placa de cocción.
La instalación de la campana debe ser realizada por un técnico especializado.
No conecte el aparato a la red eléctrica antes de terminar totalmente la instalación.
ADVERTENCIA: Producto con peso excesivo; la campana extractora ha de ser transportada e instalada
por dos o más personas.
Nota para la instalación y el uso: Antes de instalar o utilizar la campana, lea atentamente este manual. El
fabricante declina toda responsabilidad por posibles inconvenientes, daños o incendio del aparato, derivados del
incumplimiento de las instrucciones indicadas en este manual.
INSTALAÇÃO E UTILIZAÇÃO
A distância mínima entre a superfície de suporte dos recipientes no dispositivo de cozedura e a parte mais baixa
do exaustor do fogão DEVE SER SUPERIOR a 50 cm no caso de fogões eléctricos e de 65 cm no caso de fogões
a gás ou mistos. Além disso, antes da instalação, verifique as distâncias indicadas no manual da placa.
A instalação do exaustor deve ser efectuada por um técnico qualificado.
Não ligue o aparelho à corrente eléctrica enquanto a instalação não estiver concluída.
ADVERTÊNCIA: Produto com peso excessivo. A movimentação e a instalação do exaustor devem ser
feitas por pelo menos duas ou mais pessoas.
Nota de instalação e utilização: Antes de instalar ou utilizar o exaustor ler atentamente o manual de
instruções. Declina-se toda e qualquer responsabilidade por eventuais inconvenientes, danos ou incêndios
provocados pelo aparelho derivados do não seguimento das instruções que se encontram neste manual.
INSTALLAZIONE E USO
La distanza minima fra la superficie di supporto dei recipienti sul dispositivo di cottura e la parte più bassa della
cappa da cucina NON DEVE ESSERE INFERIORE a 50 cm in caso di cucine elettriche e a 65 cm in caso di cucine
a gas o miste. Prima dell’installazione, inoltre, verificare le distanze indicate nel manuale del piano cottura.
L’installazione della cappa deve essere effettuata da un tecnico specializzato.
Non collegare l’apparecchio alla rete elettrica fino ad installazione ultimata.
AVVERTENZA: Prodotto dal peso eccessivo, la movimentazione e installazione della cappa deve essere
fatta da almeno due o più persone.
Nota di installazione ed uso: Prima di installare o utilizzare la cappa leggere attentamente questo manuale. Si
declina ogni responsabilità per eventuali inconvenienti, danni o incendi provocati all’apparecchio derivati
dall’inosservanza delle istruzioni riportate in questo manuale.
ΕΓΚΑΤΑΣΤΑΣΗ ΚΑΙ ΧΡΗΣΗ
Η ελάχιστη απόσταση ανάμεσα στην επιφάνεια στήριξης των σκευών στη συσκευή μαγειρέματος και στο
χαμηλότερο σημείο του απορροφητήρα ΔΕΝ ΠΡΕΠΕΙ ΝΑ ΕΙΝΑΙ ΜΙΚΡΟΤΕΡΗ από 50 cm σε περίπτωση
ηλεκτρικών εστιών και 65 cm σε περίπτωση εστιών αερίου ή μικτής λειτουργίας. Επίσης, πριν από την
εγκατάσταση, ελέγξτε τις αποστάσεις που αναγράφονται στο εγχειρίδιο της μονάδας εστιών
.
Η εγκατάσταση του απορροφητήρα πρέπει να διεξάγεται από καταρτισμένο τεχνικό.
Μη συνδέετε τη συσκευή στο ηλεκτρικό ρεύμα πριν από την ολοκλήρωση της εγκατάστασης.
ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Προϊόν μεγάλου βάρους. Η μετακίνηση και η εγκατάσταση του απορροφητήρα
πρέπει να γίνεται τουλάχιστον από δύο ή περισσότερα άτομα.
Σημείωση για την εγκατάσταση και τη χρήση: Διαβάστε προσεκτικά αυτό το εγχειρίδιο πριν από την
εγκατάσταση ή τη χρήση του απορροφητήρα. Ο κατασκευαστής δεν φέρει καμία ευθύνη για
ενδεχόμενες βλάβες,
ζημιές ή πυρκαγιές που προκαλούνται από τη συσκευή και οφείλονται στη μη
τήρηση των οδηγιών του παρόντος εγχειριδίου.
E
P
I
GR
5019 318 33313
INSTALLATION OCH ANVÄNDNING
Avståndet mellan kokkärl och nedre delen av fläkten FÅR INTE VARA UNDER 50 cm för elektriska plattor, och
minst 65 cm för gasplattor, eller blandade plattor. Innan du installerar apparaten skall du därför först verifera
säkerhetsavstånden i spishällens instruktionsbok.
Installation skall utföras av behörig fackman.
Anslut inte apparaten till elnätet förrän installationen har avslutats helt.
VARNING: Produkt med hög vikt. För flyttning och installation av fläktkåpan krävs minst två personer.
Notering för installation och användning: Innan du installerar eller använder fläktkåpan, läs manualen
noggrant. Tillverkaren kan inte ställas till svars för eventuella fel, skador eller bränder orskade på apparaten som
uppstått på grund av underlåtenhet att iaktta anvisningarna i denna manual.
INSTALLASJON OG BRUK
Minimumsavstanden mellom varmesonene på kokeapparatet og undersiden av kjøkkenventilatoren MÅ IKKE
VÆRE MINDRE enn 50 cm for elektriske komfyrer og 65 cm for gasskomfyrer og kombinasjonskomfyrer. Før
installasjon må man også kontrollere avstandene som er oppgitt i bruksanvisningen for platetoppen.
Installasjon av ventilatoren skal utføres av en autorisert elektriker.
Koble ikke apparatet til strømnettet før installasjonen er helt avsluttet.
ADVARSEL: Dette produktet er svært tungt. Flytting og installasjon av kjøkkenventilatoren må derfor
utføres av to eller flere personer.
Anmerkning om installasjon og bruk: Før installasjon og bruk av ventilatoren må du lese denne
bruksveiledningen nøye. Produsenten fraskriver seg ethvert ansvar for eventuelle problemer, skader eller brann
på apparatet som skyldes at instruksene i denne bruksanvisningen ikke følges.
INSTALLATION OG BRUG
Minimumafstanden mellem komfurets øverste del og emhættens nederste del SKAL VÆRE PÅ MINDST 50 cm
for elkomfurer og 65 cm for gaskomfurer eller el-/gaskomfurer. Før installationen skal man desuden kontrollere
de angivne afstande i vejledningen for komfuret.
Installationen skal udføres af en elinstallatør.
Apparatet må ikke sluttes til strømforsyningen, før installationen er fuldført.
ADVARSEL: Da apparatet har meget stor vægt, skal flytning og montering af emhætten foretages af mindst
to eller flere personer.
Bemærk inden installation og brug: Læs denne vejledning inden installation og brug af emhætten.
Producenten fralægger sig ethvert ansvar for eventuelle problemer, skader eller brande i apparatet, der skyldes
manglende overholdelse af anvisningerne i denne håndbog.
ASENNUS JA KÄYTTÖ
Minimietäisyys liedellä olevan keittoastioiden alustan ja liesituulettimen alareunan välillä EI SAA OLLA ALLE 50
cm kun kyseessä on sähköliesi ja 65 cm kun kyseessä on kaasu- tai sekaliesi. Ennen asennusta on myös
tarkistettava keittotason käyttöohjeissa olevat mitat.
Liesituulettimen asennus tulee antaa erikoiskoulutuksen saaneen asentajan suoritettavaksi.
Älä kytke laitetta sähköverkkoon ennen kuin kaikki asennusvaiheet on suoritettu.
VAROITUS: Liesituuletin on painava, ja sen siirtämisessä ja asennuksessa tarvitaan vähintään kaksi henkilöä.
Asennusta ja käyttöä koskeva huomautus: Lue tämä käyttöopas huolellisesti ennen liesituulettimen
asennusta ja käyttöä. Valmistaja ei vastaa yllä mainittujen ohjeiden noudattamisen laiminlyönnistä johtuneesta
laitteen aiheuttamasta ongelmasta, vahingosta tai tulipalosta.
S
N
DK
FIN
5019 318 33313
INSTALACJA I UŻYTKOWANIE
Minimalna odległość między powierzchnią gotowania kuchenki a dolną częścią okapu POWINNA
WYNOSIĆ CO NAJMNIEJ 50 cm w przypadku kuchenek elektrycznych lub 65 cm w przypadku
kuchenek gazowych hybrydowych. Ponadto, przed montażem należy sprawdzić odległości podane w
instrukcji obsługi płyty kuchennej.
Okap powinien zainstalować wykwalifikowany technik specjalista.
Nie podłączać urządzenia do sieci zasilającej dopóki instalacja nie jest całkowicie zakończona.
OSTRZEŻENIE: Urządzenie jest ciężkie. Przenoszenie i instalacja okapu powinny być
wykonywane przez co najmniej dwie osoby.
Uwaga dotycząca instalacji i eksploatacji: Przed przystąpieniem do instalowania lub eksploatacji
okapu należy uważnie zapoznać się z niniejszą instrukcją. Wykonawca zrzeka się odpowiedzialności
za wszelkie problemy, uszkodzenia lub pożar spowodowane przez urządzenie, a wynikające z
nieprzestrzegania instrukcji.
INSTALACE A POUŽITÍ
Minimální vzdálenost mezi plotýnkami nádob na sporáku a nejnižší částí kuchyňského odsavače
NESMÍ BÝT MENŠÍ NEŽ 50 cm u elektrických sporáků a 65 cm u sporáků na plyn nebo kombinovaných
sporáků. Před začátkem instalace zkontrolujte vzdálenosti uvedené v návodu k varné desce.
Instalaci musí provést odborný technik.
Spotřebič připojte k elektrické síti až po úplném dokončení instalace.
UPOZORNĚNÍ: Vzhledem k tomu, že je odsavač par velmi těžký, musí jeho stěhování a instalaci
provádět nejméně dvě osoby.
Poznámka k instalaci a použití: před instalací nebo použitím odsavače si pozorně přečtěte tento
návod. Výrobce odmítá jakoukoli odpovědnost za případné potíže, škody nebo požár způsobené
spotřebičem a vzniklé nedodržením pokynů uvedených v této příručce.
INŠTALÁCIA A POUŽÍVANIE
Minimálna vzdialenost’ medzi plochou varnej dosky a najnižšej časti odsávača pár NESMIE BYT’
MENŠIA ako 50 cm v prípade elektrickej varnej dosky a 65 cm v prípade plynovej alebo kombinovanej
varnej doske. Pred inštaláciou, treba okrem iného, skontrolovat’ vzdialenosti uvedené v návode na
použitie varnej dosky.
Odsávač pár smie nainštalovat’ výhradne špecializovaný technik.
Spotrebič nezapájajte k elektrickej sieti, kým nie je úplne ukončená jeho inštalácia.
VAROVANIE: Výrobok má nadmernú hmotnost’, preto je nevyhnutné, aby ho prenášali a
inštalovali aspoň dve alebo viac osôb.
Poznámka pre inštaláciu a používanie: Pred inštaláciou alebo používaním odsávača si pozorne
prečítajte tento návod. Odmieta sa akákoľvek zodpovednost’ za prípadné problémy, škody alebo
požiare spôsobené spotrebičom, vyplývajúce z nedodržania pokynov uvedených v tomto návode.
ÜZEMBE HELYEZÉS ÉS HASZNÁLAT
A konyhai elszívó legalacsonyabb része és a főzőberendezésen kialakított edényfelület közötti
távolságnak elektromos tűzhely esetén legalább 50 cm, gáz- vagy vegyes tűzhely esetén pedig
legalább 65 cm NAGYSÁGÚNAK KELL LENNIE. Az üzembe helyezés előtt ellenőrizze a főzőlap
használati útmutatójában feltüntetett távolságokat is.
A szagelszívó beépítését szakembernek kell végeznie.
A készüléket csak akkor szabad áram alá helyezni, ha az üzembe helyezés már befejeződött.
FIGYELMEZTETÉS: Nagy súlya miatt a készülék mozgatását és üzembe helyezését legalább két
vagy több személynek kell végeznie.
Megjegyzés a beépítéshez és a használathoz: A szagelszívó beépítése és használata előtt
figyelmesen olvassa el a jelen kézikönyvet. A gyártó semmilyen felelősséget nem vállal a készülékben
esetlegesen keletkező azon meghibásodásokért, sérülésekért vagy tüzekért, amelyeket a jelen
füzetben foglalt utasítások be nem tartása okoz.
PL
CZ
SK
H
5019 318 33313
УСТАНОВКА И ЭКСПЛУАТАЦИЯ ВЫТЯЖКИ
Расстояние между опорной поверхностью для посуды на плите и самой нижней частью
вытяжки ДОЛЖНО СОСТАВЛЯТЬ НЕ МЕНЕЕ 50 cm в случае электрических плит и не менее
65 cm в случае газовых или комбинированных плит. Кроме того, перед установкой
необходимо проверить соблюдение расстояний, указанных в инструкциях по эксплуатации
варочной панели.
Установка вытяжки должно выполняться квалифицированным специалистом.
Не подключайте вытяжку к сети электропитания до окончательного завершения монтажа.
ОСТОРОЖНО! Устройство отличается большим весом; для его переноски и установки
требуется участие не менее двух человек.
Замечание по установке и эксплуатации. Перед установкой и использованием вытяжки
необходимо внимательно ознакомиться с данными инструкциями. Фирма8изготовитель
снимает с себя всякую ответственность за любые неисправности, ущерб или пожар,
возникшие в результате несоблюдения указаний, приведенных в настоящих инструкциях.
ИНСТАЛИРАНЕ И УПОТРЕБА
Минималното разстояние между опорната повърхност на съдовете върху устройството за
готвене и най8ниската част на кухненския аспиратор, НЕ ТРЯБВА ДА БЪДЕ по8малко от 50
cm за случая на електрически печки и 65 cm за печки на газ или комбинирани. Освен това,
преди инсталирането, проверете разстоянията посочени в ръководството на плота за
готвене.
Инсталирането на аспиратора трябва да се извърши от специализиран техник.
Не свързвайте уреда към електрическата мрежа, докато инсталирането не е завършено
напълно.
ВНИМАНИЕ: Уред с много голямо тегло 8 преместването и инсталирането на
аспиратора трябва да се извършва от най8малко двама души.
Бележка за инсталиране и употреба: Преди инсталиране или употреба на аспиратора,
прочетете внимателно това ръководство. Производителят не носи отговорност за каквито
и да било неудобства, повреди или запалвания, предизвикани от неспазване на
инструкциите, посочени в това ръководство.
INSTALAREA ȘI UTILIZAREA
Distanţa minimă între suprafaţa de sprijin a recipientelor de pe mașina de gătit și partea cea mai joasă
a hotei de bucătărie NU TREBUIE SĂ FIE mai mică de 50 cm în cazul plitelor electrice și de 65 cm în
cazul plitelor cu gaz sau mixte. În plus, înainte de instalare verificaţi distanţele indicate în manualul
plitei.
Instalarea hotei trebuie să fie efectuată de un tehnician specializat.
Nu conectaţi aparatul la reţeaua electrică până când nu terminaţi definitiv operaţia de instalare.
ATENŢIE: Produs cu greutate mare, deplasarea și instalarea hotei trebuie efectuate de cel puţin
două sau mai multe persoane.
Notă privind instalarea și utilizarea: Înainte de a instala sau de a utiliza hota, citiţi cu atenţie acest
manual. Producătorul nu-și asumă nicio răspundere pentru eventualele inconveniente, pagube sau
incendii provocate aparatului, rezultate din nerespectarea instrucţiunilor din acest manual.
RUS
BG
RO
5019 318 33313
?
5019 318 33313
SAFEGUARDING THE ENVIRONMENT
1. Packing
Packing materials are 100% recyclable and are marked with
the recycling symbol .Comply with the local regulations for
disposal. The packing materials (plastic bags, polystyrene,
etc.) are a potential source of danger and must be kept out of
the reach of children.
2. Product
This appliance is marked in compliance with European
Directive 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring that this appliance is correctly scrapped, the user
can help prevent potentially harmful consequences for the
environment and the health of people.
The symbol on the product or the accompanying
documentation indicates that this product should not be treated
as domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic equipment.
Disposal must be carried out in compliance with local
regulations on waste disposal.
For further information on the treatment, recovery and
recycling of this product, contact the competent local office,
the household waste collection service or the shop where
you purchased the appliance.
IMPORTANT INSTRUCTIONS FOR
SAFETY
WARNING: To reduce the risk of accidents, electric
shock, injury or damage, when using the hood comply with
the basic precautions, including the following.
1. Always disconnect the hood from the power supply
before carrying out any installation or maintenance
operation on the appliance.
2. Installation must be carried out by a specialised
technician, in compliance with the manufacturer’s
instructions and local safety regulations.
3. Earthing of the appliance is compulsory. (Not possible for
Class II hoods).
4. Never use multisockets and extension leads.
5. The electrical components must no longer be accessible
to the user after installation.
6. Do not touch the hood with wet parts of the body or use
it when barefoot.
7. Do not pull the appliance power cable to unplug it.
8. After-sales service – do not repair or replace any part of
the hood unless specifically indicated in the manual. All
other maintenance services must be carried out by a
specialised technician.
9. When drilling the wall, make sure not to damage the
electrical connections and/or pipes.
10. The ventilation ducts must always discharge to the
outside.
11. The Manufacturer declines any liability for improper use
or incorrect setting of the controls.
12. The appliance is not intended for use by children or
persons with limited physical, sensory or mental abilities
or without experience and knowledge of it, unless they
are under the supervision of or instructed in its use by a
person responsible for their safety.
13. Keep children away.
14. To reduce the risk of fire, only use a metal inlet duct.
15. Children must be supervised so that they do not play
with the appliance.
16. The product must be disposed of in compliance with
local regulations on waste disposal.
17. For further information on the treatment, recovery and
recycling of this product, contact the competent local
office, the household waste collection service or the shop
where you purchased the appliance.
18. Regular cleaning and maintenance is essential for correct
hood operation and good performance. Frequently clean
all encrustations from dirty surfaces to prevent the
accumulation of grease. Regularly clean or replace filters.
19. Do not “flambé” food under the hood. Naked flames
could cause a fire.
20. The room must have adequate ventilation when the hood
is used at the same time as appliances operating on gas or
other fuels.
21. The discharge air must not be eliminated in a duct used
to remove fumes produced by appliances operating on
gas or other fuels, but must have a separate outlet. All the
national regulations on air discharge envisaged by art.
7.12.1 of CEI EN 60335-2-31 must be observed.
22. If the hood is used together with other appliances
operating on gas or other fuels, the negative pressure in
the room must not exceed 4 Pa (4 x 10
-5
bar). Therefore,
make sure the room is adequately ventilated.
23. Do not leave pans unattended when frying, since the
cooking oil could catch fire.
24. Make sure the lamps are cold before touching them.
25. The hood is not a shelf, therefore do not overload or
place objects on it.
26. Do not use or leave the hood without its lamps correctly
installed - risk of electric shock.
27. Wear work gloves for all installation and maintenance
operations.
28. The product is not suitable for outdoor use.
29. The air sucked by the hood must not be eliminated
through the same flue of the heating system or other
appliances using gas or other fuels.
FINNL P I GR
E
S
N
DK
D
F
GB
CZ SK H
PL
RUS
BG
RO
5019 318 33313
Electrical connection
The mains voltage must match that given on the rating plate
located inside the hood. If provided with a plug, connect the
hood to a socket complying with the current regulations and
located in an accessible area. If it does not have a plug (direct
connection to the power supply) or if the plug is not in an
accessible place, fit a suitable double-pole switch that ensures
complete disconnection from the power supply in category III
overvoltage conditions, complying with the installation rules.
WARNING: Before reconnecting the hood circuit to the
power supply and checking correct operation, always make
sure the power cable is correctly fitted and that it was NOT
crushed in its housing during installation. Make sure to have
this operation carried out by a specialised technician.
Cleaning the hood
WARNING: Failure to remove oil/grease (at least once a
month) could result in fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Before using the hood
Please read these instructions carefully and keep them for
future reference, in order to ensure best use of your hood.
The packing materials (plastic bags, polystyrene, etc.) are a
potential source of danger and must be kept out of the reach
of children.
Make sure the hood has not been damaged during transport.
Declaration of conformity
This product has been designed, manufactured and put on
the market in conformity with:
- safety objectives of the “Low Voltage” Directive
2006/95/EC (which replaces 73/23/EEC as amended)
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
If the hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
If the hood is not extracting enough:
• Is the right speed selected?
• Do the filters need cleaning or replacing?
• Are the air outlets blocked?
If the lamp does not work:
• Does the lamp need replacing?
• Is the lamp correctly fitted?
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself
(see “Troubleshooting Guide”).
2. Switch the appliance off and then on again to check if the
problem has been eliminated.
3. If the problem persists, contact the After-Sales Service.
Specify:
• the type of fault,
• the product model given on the dataplate inside the
hood, visible on removing the grease filters,
• your full address,
• your telephone number and area code,
• the Service code (the number under the word SERVICE
on the dataplate inside the hood, behind the grease
filter).
If any repairs are necessary, contact an authorised Service
Centre (to ensure the use of original spare parts and correct
repair).
Failure to comply with these instructions can compromise
the safety and quality of the product.
FINNL P I GR
E
S
N
DK
D
F
GB
CZ SK H
PL
RUS
BG
RO
5019 318 33313
EXTRACTOR OR FILTERING HOOD INSTALLATION
The hood is designed for use in “Extractor version” or in “Filter version”.
Extractor version
Fumes are extracted and expelled to the outside through an exhaust pipe (not supplied) fixed to the hood exhaust pipe
connector B.
Depending on the exhaust pipe purchased, provide for suitable fixing to the exhaust pipe connector.
Important: If already installed, remove the carbon filter/s.
Filter version
Air is filtered through the carbon filter/s and recycled into the surrounding environment.
Important: check that air recirculation is facilitated.
Important: If the hood does not have a carbon filter/s, order one/them and fit it/them before use.
The instructions below, to be performed in order as numbered, refer to the diagram with reference numbers found on the
next page.
Remove the grease filter/s and the carbon filter holder.
Preassembly of steam deflector on the motor assembly: (a.) fit the steam deflector on the rails of the motor assembly, (b.)
carry out the control, sensor and lamp connections, (c.) secure with 6 screws.
Note: The control and sensor twin-lead connections must be carried out respecting the letters on the twin-lead sheathing.
1. Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood.
2. Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-line drawn on
the wall. The template's bottom edge represents the bottom edge of the hood.
3. Place the mounting bracket over the drilling template so that it matches the outlined rectangle, mark and drill the two
external holes. Remove the drilling template, insert 2 wall plugs and fix the hood mounting bracket with 2 screws.
4. Hook the hood to the bracket.
5. Adjust the distance between the hood and the wall.
6. Adjust the hood horizontally.
7. From inside the hood, mark a hole for the final fixing of the hood.
8. Remove the hood from the bracket.
9. Drill (Ø 8 mm).
10. Insert 1 wall plug.
11. Apply the flue support bracket G on the wall and against the ceiling (the small slot on the support must match the line
previously drawn on the wall (step1). Drill 2 holes (Ø 8 mm) and insert 2 wall plugs.
12. Fix with 2 screws.
13. Hang the hood on the bottom mounting bracket.
14. Fix the hood to the wall with a screw.
15. Connect an exhaust pipe to the to the collar B, the fumes must be ducted to the outside (extractor version) or towards the
deflector (filter version).
Fit the deflector F to the flue support bracket G with 2 screws.
16. Make all necessary electrical connections.
17. Apply the flues and fix them with 2 screws (17a) to the flue support G (17b).
18. Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the hood.
Refit the carbon filter holder and the grease filter/s and check correct hood operation.
FINNL P I GR
E
S
N
DK
D
F
GB
CZ SK H
PL
RUS
BG
RO
5019 318 33313
5019 318 33313
Description and use of hood
1. Control panel.
2. Grease filters.
3. Halogen lamps.
4. Telescopic flue.
5. Sensors.
Digital control panel with sensors
1. Motor ON/OFF
Press the button and the hood starts at speed 1.
Press the button during operation and the hood switches
OFF.
2. Increase speed / Speed timing
Press the button and the hood goes from OFF to speed 1.
Press the button (hood ON) to increase the motor speed
from speed 1 to intensive.
The respective LED (green) lights up at each speed.
Speed 1 LED “L1”
Speed 2 LED “L2”
Speed 3 LED “L3”
Intensive speed LED “L4” (blinking)
The Intensive speed is timed. The standard operating
time is 5 minutes, after which the hood goes to speed 2.
To deactivate the function before the time has elapsed,
press button “2”, the hood will go to speed 1; press
button 1 and the hood will switch off.
3. Light ON/OFF switch
4. ON/OFF sensor
5. Operation status indicator
Speed timing
Press button “2” for 2 seconds to enable speed timing; the
hood switches off when the time has elapsed.
Operation times are as follows:
Speed 1 20 minutes (LED “L1” blinking)
Speed 2 15 minutes (LED “L2” blinking)
Speed 3 10 minutes (LED “L3” blinking)
Intensive speed 5 minutes (LED “L4” blinking)
During timed operation, press button “1” to switch off the
hood; press button “2” to return to the set speed; press
button “4” and the hood switches to “Cooking” mode.
Grease filter signalling
After 80 hours of operation, LEDs “L1” and “L2” blink.
When this signalling occurs, the grease filter installed needs to
be cleaned.
To reset the signalling, keep button “1” pressed for 3 seconds”.
Carbon filter signalling
After 320 hours of operation, LEDs “L2” and “L3” blink.
When this signalling occurs, the carbon filter installed needs
to be replaced.
To reset the signalling, keep button “1” pressed for 3
seconds”.
In case of signalling of both filters at the same time, LEDs
“L1”, “L2” and “L3” blink.
Reset by carrying out the above procedure twice.
The first time resets grease filter signalling; the second resets
carbon filter signalling.
Carbon filter signalling is not active in the standard mode.
If using the hood in filter version, it is necessary to activate
carbon filter signalling.
Activating carbon filter signalling:
Switch the hood OFF and keep buttons “2” and “3” pressed
at the same time for 3 seconds”.
LEDs “L1” and “L2” will blink for 2 seconds”.
Deactivating carbon filter signalling:
Switch the hood OFF and keep buttons “2” and “3” pressed
at the same time for 3 seconds”.
LED “L1” will blink for 2 seconds”.
Automatic operation
The system default setting is manual mode; press button “4”
to activate automatic mode”.
The system provides for automatic operation in 2 modes:
- COOKING mode, which guarantees correct extraction of
fumes during cooking.
- AIR QUALITY CONTROL mode, which is a monitoring
system that guarantees a high air quality level.
The 2 modes are activated cyclically by pressing button “4”.
COOKING mode LED “L5” (amber) on.
During cooking, the system promptly reacts to Steam/Gas
increases and remains at the set speed for at least 1 minute,
before returning to the lowest speed/switching off.
At the end of cooking and when the ambient parameters
have returned to the levels prior to cooking, the system
switches off.
If the parameters are close to the rest condition, the system
forces hood switch-off after 30 minutes.
FINNL P I GR
E
S
N
DK
D
F
GB
CZ SK H
PL
RUS
BG
RO
5019 318 33313
AIR QUALITY CONTROL mode, LED “L5” (white) on.
The system promptly reacts to Steam/Gas increases and
remains at the set speed for at least 1 minute, before
returning to the lowest speed/switching off.
When the effect of the Steam/Gas has finished and the
ambient parameters have returned to the levels prior to
start, the system switches off.
Press buttons “1”, “2” and “4” to exit this mode”.
Sensor test
This occurs continuously during automatic operation. In case
of a failure, all the LEDs blink (contact the After Sales
Service); in any case, the hood can be used in manual mode.
Manual calibration
Switch the hood OFF and keep buttons “1” and “4” pressed
at the same time for 3 seconds”.
LED “L5” blinking.
It is advisable to carry out this operation:
when the hood is installed for the first time
when the power supply has been disconnected for many
hours or days
when a sudden temperature changes occurs in the kitchen
Cooking hob selection
This operation optimises automatic hood operation; proceed
as follows:
Switch the hood OFF
Keep buttons “1” and “3” pressed at the same time for 3
seconds until the cooking hob in use is displayed.
LED “L1” on: Gas hob
LED “L2” on: Induction hob
LED “L3” on: Electric hob
Press button “1” for cyclic selection of the hob”
Confirmation of the selected hob is displayed by the
corresponding LED blinking 3 times.
After selecting the hob, wait 10 seconds for function
confirmation”.
The default setting is Gas hob.
Maintenance
Grease filters:
Metal grease filters have an unlimited life
and should be washed once a month
either by hand or in a dishwasher at a
low temperature and with a short cycle.
Washing in a dishwasher can cause
grease filters to turn white, but this in no
way affects efficiency.
a. press the handle to remove the filter
b. remove it.
Wash the filter and leave it to dry, proceeding in reverse
order to refit it.
Replacing the halogen bulbs:
1. Disconnect the hood from the mains power supply.
WARNING: Wear gloves.
2. Use a small screwdriver to gently prise the lamp cover off
(at the points indicated in Fig. 3).
3. Remove the burnt-out lamp and fit a new one.
WARNING: Replace using 20W max G4 halogen bulbs
only.
Close the lighting unit (snap-on).
Active carbon filter
(filter hoods only):
The carbon filter must be cleaned once a month in a
dishwasher at the highest temperature, using a normal
dishwasher detergent. Wash the filters on their own.
After washing, reactivate the carbon filter by drying it in the
oven at 100°C for 10 minutes.
Change the carbon filter every 3 years.
Fitting the carbon filter:
1. Remove the grease filter.
2. Remove the filter holder by turning the knobs 90°.
3. Fit the carbon filter “i” in the filter holder “h”.
Reverse the above procedure to re-fit the filter holder and
grease filter.
a
b
FINNL P I GR
E
S
N
DK
D
F
GB
CZ SK H
PL
RUS
BG
RO
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Whirlpool AKR 798 IX Manualul utilizatorului

Whirlpool
Marca
Whirlpool
Model
AKR 798 IX
Categorie
Hote pentru aragaz
Tip
Manualul utilizatorului
Descărcați PDF
raport

în alte limbi

Lucrări conexe

Alte documente