Sonicare HX8424/30 Manual de utilizare

ProtectiveClean

4500/5100

EN: User manual

RU: Руководство пользователя

KZ: Пайдаланушы нұсқаулығы

1

2

10

4

3

5

6

7

8

9

1

English 6

Čeština 20

Eesti 34

Hrvatski 47

Latviešu 61

Lietuviškai 74

Magyar 88

Polski 103

Română 119

Slovenščina 134

Slovensky 148

Srpski 163

Български 175

Русский 191

Українська 205

Қазақша

218

English

Important

Read this user manual carefully before you use the appliance and

save it for future reference.

Danger

-

Keep the charger away from water. Do not

place or store it over or near water

contained in a bathtub, washbasin, sink etc.

Do not immerse the charger in water or any

other liquid. After cleaning, make sure the

charger is completely dry before you

connect it to the mains.

Warning

-

The mains cord cannot be replaced. If the

mains cord is damaged, discard the charger.

-

Always have the charger replaced with one

of the original type in order to avoid a

hazard.

-

Do not use the charger outdoors or near

heated surfaces.

6

English

-

If the appliance is damaged in any way

(brush head, toothbrush handle or charger),

stop using it. This appliance contains no

serviceable parts. If the appliance is

damaged, contact the Consumer Care

Center in your country (see chapter

'Warranty and support').

-

This appliance can be used by children and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Cleaning and user

maintenance shall not be made by children

without supervision.

-

Children shall not play with the appliance.

Caution

-

Do not clean the brush head, the handle or

the charger in the dishwasher.

-

If you have had oral or gum surgery in the

previous 2 months, consult your dentist

before you use the toothbrush.

7

English

-

Consult your dentist if excessive bleeding

occurs after using this toothbrush or if

bleeding continues to occur after 1 week of

use. Also consult your dentist if you

experience discomfort or pain when you use

the Philips Sonicare.

-

The Philips Sonicare toothbrush complies

with the safety standards for

electromagnetic devices. If you have a

pacemaker or other implanted device,

contact your physician or the device

manufacturer of the implanted device prior

to use.

-

If you have medical concerns, consult your

doctor before you use the Philips Sonicare.

-

This appliance has only been designed for

cleaning teeth, gums and tongue. Do not

use it for any other purpose. Stop using the

appliance and contact your doctor if you

experience any discomfort or pain.

8

English

-

The Philips Sonicare toothbrush is a

personal care device and is not intended for

use on multiple patients in a dental practice

or institution.

-

Stop using a brush head with crushed or

bent bristles. Replace the brush head every

3 months or sooner if signs of wear appear.

Do not use other brush heads than the ones

recommended by the manufacturer.

-

If your toothpaste contains peroxide, baking

soda or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush

head with soap and water after each use.

This prevents possible cracking of the

plastic.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

Radio Equipment Directive

- Radio Equipment in this product operates at 13.56 MHz

- Maximum RF power transmitted by the Radio Equipment is

30.16dBm

Introduction

Congratulations on your purchase and welcome to Philips! To fully

benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

9

English

Your Philips Sonicare (Fig. 1)

1 Hygienic travel cap

2 Smart brush head(s)*

3 Handle

4 Power on/off button

5 Mode/intensity button

6 Mode light

7 Brush head replacement reminder light

8 Battery indication

9 Charging base

10 Travel case (specific types only)*

*Note: The content of the box may vary based on the model

purchased.

Brush heads

Your Philips Sonicare comes with one or more brush heads which are

designed to deliver superior results for your oral care needs.

Philips Sonicare BrushSync Technology

Your smart brush heads use a microchip to sync with your handle,

enabling brush head replacement reminder. For more information

regarding the brush head replacement reminder, see 'Features'.

This symbol indicates the brush head is equipped with BrushSync

technology. (Fig. 2)

Brushing modes

To toggle between modes press the mode button located below the

on/off button.

Your power toothbrush is equipped with either 2 or 3 brushing

modes, depending on your model.The following modes are available:

Clean mode

Clean is a 2-minute mode. It gives you a thorough and complete

clean and is recommended to be used with the C2 Optimal Plaque

Control brush head.

10

English

White mode

White is a 2-minute 30-seconds mode, recommended to be used

with the W2 Optimal White brush head.

Gum Care mode

Gum Care is a 3-minute mode, recommended to be used with the G2

Optimal Gum Care brush head.

Using your Philips Sonicare

Brushing instructions

1 Press the brush head onto the handle in such a way that the

bristles will face the front of the handle. (Fig. 3)

2 Firmly press the brush head down onto the metal shaft until it

stops.

Note: It is normal to see a slight gap between the brush head and

the handle.

3 Wet the bristles. (Fig. 4)

4 Apply a small amount of toothpaste on the bristles. (Fig. 5)

5 Place the toothbrush bristles against the teeth at a slight angle (45

degrees), pressing firmly to make the bristles reach the gumline or

slightly beneath the gumline. (Fig. 6) A change in vibration (and a

slight change in sound) alerts you when you apply too much

pressure while brushing.

Note: Keep the center of the brush in contact with the teeth at all

times.

6 Press the power on/off button to turn on the Philips Sonicare. (Fig.

7)

7 Gently keep the bristles placed on the teeth and in the gumline.

Brush your teeth with small back and forth motion so the bristles

reach between the teeth. (Fig. 8)

Note: The bristles should slightly flare. Do not scrub.

8 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing

strokes on each tooth. (Fig. 9)

11

English

9 To make sure you brush evenly throughout the mouth, divide the

mouth into 4 sections using the Quadpacer feature. (Fig. 10) The

quadpacer feature beeps after 30 seconds.

10 Brush for the full 2 minutes following the Quadpacer. (Fig. 11) After

2 minutes, the toothbrush will automatically shut off.

In white mode, after 2 minutes the handle will continue to brush

for 30 seconds so that you can brighten and polish your front

teeth.

In gum care mode, after 2 minutes the handle will continue to

brush for an additional minute so you can gently stimulate and

massage your gums.

- After you have completed the brushing cycle, you can spend

additional time brushing the chewing surfaces of your teeth and

areas where staining occurs. (Fig. 12)

Your Philips Sonicare toothbrush is safe to use on:

- Braces (brush heads wear out sooner when used on braces)

- Dental restorations (fillings, crowns, veneers)

Note: When the Philips Sonicare toothbrush is used in clinical studies,

it must be used in the Clean mode (for plaque and gum health claims)

or in White mode (for whitening claims) at high intensity with

EasyStart turned off.

Features

- EasyStart

- Brush head replacement reminder

- Pressure sensor

- Quadpacer

EasyStart

This Philips Sonicare model comes with the EasyStart feature

activated. The EasyStart feature gently increases the power over the

first 14 brushings to help you get used to the brushing with the Philips

Sonicare. The EasyStart feature works in all modes.

To deactivate EasyStart see 'Activating or deactivating features'.

12

English

Brush head replacement reminder

Your Philips Sonicare is equipped with BrushSync technology that

tracks the wear of your brush head. (Fig. 13)

1 When attaching a new smart brush head for the first time the

brush head replacement reminder light blinks green three times.

This confirms you have a Philips brush head with BrushSync

technology.

2 Over time, based on the pressure you apply and the amount of

time used, the handle will track brush head wear in order to

determine the optimal time to change your brush head. This

feature gives you the guarantee for the best cleaning and care of

your teeth.

3 When the brush head replacement reminder light lights up amber,

you should replace your brush head.

To deactivate the brush head replacement reminder see 'Activating or

deactivating features'.

Pressure sensor

Your Philips Sonicare is equipped with an advanced sensor that

measures the pressure you apply while brushing. If you apply too

much pressure, the toothbrush will provide immediate feedback to

indicate that you need to reduce the pressure. This feedback is given

by a change in vibration and therefore brushing sensation.

To deactivate the pressure sensor see 'Activating or deactivating

features'.

Quadpacer

The Quadpacer is an interval timer that has a short beep and pause

to remind you to brush the different sections of your mouth.

Depending on the brushing mode you have selected (see 'Brushing

modes'), the Quadpacer beeps at different intervals during the

brushing cycle.

Activating or deactivating features

You can activate or deactivate the following features of your

toothbrush:

13

English

- EasyStart

- Brush head replacement reminder

- Pressure sensor

To activate or deactivate these features, follow the instructions

below:

EasyStart

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a single

short beep (after 2 seconds).

4 Release the power on/off button.

-

Triple tone of low-med-high means the EasyStart feature has

been activated. The brush head replacement light and battery

light will also blink green 3 times in unison to confirm activation.

-

Triple tone of high-med-low means the EasyStart feature has

been deactivated. The brush head replacement light and

battery light will also blink amber 3 times in unison to confirm

deactivation.

Note: To achieve clinical efficacy, EasyStart needs to be deactivated.

Brush head replacement reminder

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a series of

two short beeps (after 4-5 seconds).

4 Release the power on/off button.

-

Triple tone of low-med-high means the Brush head

replacement reminder feature has been activated. The brush

head replacement light and battery light will also blink green 3

times in unison to confirm activation.

14

English

-

Triple tone of high-med-low means the Brush head

replacement reminder feature has been deactivated. The brush

head replacement light and battery light will also blink amber 3

times in unison to confirm deactivation.

Pressure sensor

1 Put the handle on the plugged-in charger.

2 Press and hold the power on/off button while the handle remains

on the charger.

3 Keep the power on/off button pressed until you hear a series of

three short beeps (after 6-7 seconds).

4 Release the power on/off button.

-

Triple tone of low-med-high means the pressure sensor feature

has been activated. The brush head replacement light and

battery light will also blink green 3 times in unison to confirm

activation.

-

Triple tone of high-med-low means the pressure sensor feature

has been deactivated. The brush head replacement light and

battery light will also blink amber 3 times in unison to confirm

deactivation.

If you continue holding the power on/off button after the three short

beeps, the activate/deactivate sequence repeats.

Battery status and charging

1 Put the plug of the charger in an electrical outlet.

2 Place the handle on the charger.

-

The charger will emit 2 short beeps to confirm that the handle is

placed properly.

-

The flashing light of the battery level indicator shows that the

toothbrush is charging.

-

When handle is fully charged on the charger, the battery light

shows solid green for 30 seconds and switches off.

Note: Your toothbrush comes pre-charged for first use. After first use,

charge for at least 24 hours.

15

English

Battery status (when handle is not on charger)

When removing the Philips Sonicare from the charger, the battery

light at the bottom of the toothbrush will indicate the status of the

battery life.

- Solid green LED: full battery

- Flashing green LED: medium battery

- Flashing amber LED and three beeps: low battery

- Flashing amber LED and two sets of five beeps: No brushing

sessions left (charge toothbrush)

Cleaning

Note: Do not clean the brush head, handle or travel case in the

dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water. Make sure you remove any residual toothpaste (Fig. 14).

Note: Do not push on the rubber seal on the metal shaft with

sharp objects, as this may cause damage.

2 Wipe the entire surface of the handle with a damp cloth.

Note: Do not use isopropyl rubbing alcohol, vinegar or bleach to

clean handle as this may cause discoloration.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 15).

2 Remove the brush head from the handle and rinse the brush head

connection with warm water at least once a week.

Charger

1 Unplug the charger before you clean it.

2 Wipe the surface of the charger with a damp cloth.

Storage

If you are not going to use your Philips Sonicare for an extended

period of time, unplug the charger from the wall socket, clean it and

store it in a cool and dry place away from direct sunlight.

16

English

Locating the model number

Look on the bottom of the Philips Sonicare toothbrush handle for the

model number (HX682x/HX683x).

Recycling

- This symbol means that this product shall not be disposed of with

normal household waste (2012/19/EU) (Fig. 24).

- This symbol means that this product contains a built-in

rechargeable battery which shall not be disposed of with normal

household waste (Fig. 25) (2006/66/EC). Please take your product

to an official collection point or a Philips service center to have a

professional remove the rechargeable battery.

- Follow your country’s rules for the separate collection of electrical

and electronic products and rechargeable batteries. Correct

disposal helps prevent negative consequences for the

environment and human health.

Removing the rechargeable battery

Warning: Only remove the rechargeable battery when you discard the

appliance. Make sure the battery is completely empty when you

remove it.

To remove the rechargeable battery, you need a towel or cloth, a

hammer and a flat-head (standard) screwdriver. Observe basic safety

precautions when you follow the procedure outlined below. Be sure

to protect your eyes, hands, fingers, and the surface on which you

work.

1 To deplete the rechargeable battery of any charge, remove the

handle from the charger, turn on the Philips Sonicare and let it run

until it stops. Repeat this step until you can no longer turn on the

Philips Sonicare.

2 Remove and discard the brush head. Cover the entire handle with

a towel or cloth (Fig. 16).

3 Hold the top of the handle with one hand and strike the handle

housing 0.5 inch above the bottom end. Strike firmly with a

hammer on all 4 sides to eject the end cap (Fig. 17).

17

English

Note: You may have to hit on the end several times to break the

internal snap connections.

4 Remove the end cap from the toothbrush handle. If the end cap

does not release easily from the housing, repeat step 3 until the

end cap is released (Fig. 18).

5 Holding the handle upside down, press the shaft down on a hard

surface. If the internal components do not easily release from the

housing, repeat step 3 until the internal components are released

(Fig. 19).

6 Remove the rubber battery cover.

7 Wedge the screwdriver between the battery and the black frame

at the bottom of the internal components. Then pry the

screwdriver away from the battery to break the bottom of the

black frame (Fig. 20).

8 Insert the screwdriver between the bottom of the battery and the

black frame to break the metal tab connecting the battery to the

green printed circuit board. This will release the bottom end of the

battery from the frame (Fig. 21).

9 Grab the battery and pull it away from the internal components to

break the second metal battery tab (Fig. 22).

Caution: Be aware of the sharp edges of the battery tabs so as to

avoid injury to your fingers.

10 Cover the battery contacts with tape to prevent any electrical short

from residual battery charge. The rechargeable battery can now be

recycled and the rest of the product discarded appropriately (Fig.

23).

Warranty and support

If you need information or support, please visit

www.philips.com/support or read the international warranty leaflet.

Warranty restrictions

The terms of the international warranty do not cover the following:

- Brush heads.

- Damage caused by use of unauthorized replacement parts.

18

English

- Damage caused by misuse, abuse, neglect, alterations or

unauthorized repair.

- Normal wear and tear, including chips, scratches, abrasions,

discoloration or fading.

19

English

Čeština

Důležité

Před použitím přístroje si pečlivě přečtěte tuto uživatelskou příručku a

uschovejte ji pro budoucí použití.

Nebezpečí

-

Chraňte nabíječku před kontaktem svodou.

Nepokládejte a neuskladňujte nabíječku

vblízkosti vody, například u vany

snapuštěnou vodou, umyvadla, dřezu apod.

Neponořujte nabíječku do vody ani jiné

kapaliny. Před připojením nabíječky

knapájení se ujistěte, že je po čištění zcela

suchá.

Varování

-

Napájecí kabel nelze vyměnit. Pokud je

napájecí kabel poškozen, je nutné vyřadit

nabíječku zprovozu.

-

Nabíječku nechte vždy vyměnit za originální

typ, aby nevzniklo žádné riziko.

-

Nepoužívejte nabíječku venku aniblízko

horkých povrchů.

20

Čeština

-

Pokud dojde kjakémukoli poškození

přístroje (hlavice, rukojeť nebo nabíječka),

přestaňte jejpoužívat. Tento přístroj

neobsahuje žádné opravitelné součásti.

Pokud dojde kjeho poškození, obraťtese

nastředisko péče ozákazníky vevaší zemi

(viz „Záruka a podpora“).

-

Přístroj mohou používat děti a osoby se

sníženými fyzickými, smyslovými nebo

duševními schopnostmi nebo nedostatkem

zkušeností a znalostí, pokud jsou pod

dohledem nebo byly poučeny obezpečném

používání přístroje a rozumí všem rizikům

spojeným spoužíváním přístroje. Děti nesmí

provádět bez dozoru čištění auživatelskou

údržbu.

-

Děti si spřístrojem nesmí hrát.

Upozornění

-

Nemyjte hlavici kartáčku, rukojeť ani

nabíječku vmyčce nádobí.

21

Čeština

Pagina se încarcă ...

Sonicare HX8424/30 Manual de utilizare

Sonicare HX8424/30 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente