Yamaha RX-V2700 Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

RX-V2700

Printed in Malaysia WJ55230

RX-V2700

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

RX-V2700_G_cv.fm Page 1 Friday, August 25, 2006 1:21 AM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press MASTER ON/OFF to release it

outward to the OFF position to turn off this unit, the main

room, Zone 2 and Zone 3 and then disconnect the AC power

plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC main supply. Voltages are as follows:

.....................................AC 110/120/220/230–240 V, 50/60 Hz

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by MASTER ON/OFF. In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

This symbol mark is according to the

EU directive 2002/96/EC.

This symbol mark means that electrical

and electronic equipment, at their end-

of-life, should be disposed of separately

from your household waste.

Please act according to your local rules

and do not dispose of your old products

with your normal household waste.

1 En

English

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc.

“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks

“iPod” is a trademark of Apple Computer, Inc., registered in the

U.S. and other countries.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

This receiver supports network connections.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

Note on Source Code Distribution

This product includes software code subject to the GNU General

Public License (GPL) or the GNU Lesser General Public License

(LGPL). The copy, distribution, or change of this software code is

licensed under the terms of the GPL or the LGPL. The source

code is available at the following website:

http://www.global.yamaha.com/download/

The source code is also available on a physical media (such as a

CD-ROM) at actual cost.

Contact: AV products division, YAMAHA CORPORATION,

10-1 Nakazawa-cho, Hamamatsu 430-8650, Japan

In principle, the source code is offered for 3 years from the day of

purchase.

TRADEMARK NOTICES

iPod



2 En

FEATURES .............................................................4

GETTING STARTED............................................5

Supplied accessories.................................................. 5

CONTROLS AND FUNCTIONS..........................6

Front panel................................................................. 6

Remote control .......................................................... 8

Zone 2/Zone 3 remote control ................................. 10

Preparing the remote control ................................... 11

Front panel display .................................................. 12

Rear panel ................................................................ 14

CONNECTIONS...................................................15

Placing speakers ...................................................... 15

Connecting speakers................................................ 16

Using bi-amplification connections......................... 19

Information on jacks and cable plugs...................... 20

Information on HDMI ............................................. 21

Audio and video signal flow.................................... 22

Connecting a TV monitor or projector .................... 23

Connecting other components ................................. 24

Connecting a multi-format player

or an external decoder ......................................... 28

Connecting a YAMAHA iPod universal dock ........ 29

Using the VIDEO AUX jacks on the front panel.... 29

Connecting the network........................................... 30

Connecting the FM and AM antennas..................... 31

Connecting the power cable .................................... 32

Setting the speaker impedance ................................ 33

Turning on and off the power.................................. 34

AUTO SETUP .......................................................35

Using Auto Setup..................................................... 35

PLAYBACK ..........................................................40

Basic procedure ....................................................... 40

Selecting audio input jacks (AUDIO SELECT)...... 42

Selecting the MULTI CH INPUT component......... 43

Using your headphones ........................................... 43

Muting the audio output .......................................... 43

Operating the amplifier functions of this unit

by using the graphical user interface (GUI)

screen................................................................... 44

Playing video sources

in the background of an audio source.................. 45

Using the sleep timer ............................................... 45

SOUND FIELD PROGRAMS.............................46

Selecting sound field programs ............................... 46

Sound field program descriptions............................ 47

Enjoying unprocessed input sources........................ 51

USING AUDIO FEATURES............................... 52

Enjoying pure hi-fi sound ........................................ 52

Adjusting the tonal quality ...................................... 52

Adjusting the speaker level...................................... 53

Enjoying multi-channel sources

in 2-channel stereo .............................................. 53

Selecting the Compressed Music

Enhancer mode .................................................... 54

Selecting the night listening mode........................... 55

FM/AM TUNING ................................................. 56

FM/AM controls and functions ............................... 56

Automatic tuning ..................................................... 57

Manual tuning.......................................................... 58

Automatic preset tuning........................................... 59

Manual preset tuning ............................................... 60

Selecting preset stations........................................... 61

Exchanging preset stations ...................................... 62

RADIO DATA SYSTEM TUNING

(U.K. AND EUROPE MODELS ONLY) ....... 63

Displaying the Radio Data System information...... 63

Selecting the Radio Data System program type

(PTY SEEK mode).............................................. 64

Using the enhanced other networks (EON)

data service.......................................................... 65

USING iPod........................................................... 66

Controlling iPod ...................................................... 66

USING NETWORK/USB FEATURES.............. 68

Navigating the network and USB menus ................ 68

Using a PC server or YAMAHA MCX-2000 ......... 70

Using the Internet Radio.......................................... 71

Using a USB memory device

or a USB portable audio player ........................... 72

Using shortcut buttons............................................. 72

RECORDING ....................................................... 74

ADVANCED SOUND CONFIGURATIONS .... 75

Selecting decoders ................................................... 75

GRAPHIC USER INTERFACE (GUI)

SCREEN............................................................ 78

Stereo/Surround (Stereo/Surround menu) ............... 79

Input Select.............................................................. 85

Manual Setup (Sound)............................................. 88

Manual Setup (Video) ............................................. 92

Manual Setup (Basic) .............................................. 95

Manual Setup (NET/USB)..................................... 100

Manual Setup (Option) .......................................... 102

System Memory..................................................... 106

Signal Info. (Input signal information).................. 107

Language ............................................................... 108

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

CONTENTS

3 En

English

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

REMOTE CONTROL FEATURES................. 109

Controlling this unit, a TV, or other components ....109

Setting remote control codes ................................. 111

Programming codes from other remote controls ... 113

Changing source names in the display window..... 114

Macro programming features ................................ 115

Clearing configurations ......................................... 118

USING MULTI-ZONE CONFIGURATION.....121

Connecting the Zone 2 and Zone 3 components ... 121

Controlling Zone 2 or Zone 3 ................................ 122

ADVANCED SETUP ......................................... 125

Using ADVANCED SETUP ................................. 125

Setting remote control ID ...................................... 128

TROUBLESHOOTING..................................... 130

RESETTING THE SYSTEM............................ 140

GLOSSARY ........................................................ 141

SOUND FIELD PROGRAM

INFORMATION ............................................ 144

PARAMETRIC EQUALIZER

INFORMATION ............................................ 145

SPECIFICATIONS ............................................ 146

(at the end of this manual)

SOUND OUTPUT

IN EACH SOUND FIELD PROGRAM ............ i

GPL/LGPL.............................................................. v

LIST OF REMOTE CONTROL CODE ............. ix

ADDITIONAL INFORMATION

APPENDIX

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the

buttons on the front panel or the ones on the remote

control. In case the button names differ between the front

panel and the remote control, the button name on the

remote control is given in parentheses.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and product, the product has priority.

• This unit equips GUI display menu language switching

capability. In this manual, the illustrations of the GUI are

examples when you set the GUI language to English.

FEATURES

4 En

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(20 Hz to 20 kHz, 0.04% THD, 8 Ω)

Front: 140 W + 140 W

Center: 140 W

Surround: 140 W + 140 W

Surround back: 140 W + 140 W

Sound field programs

◆ Proprietary YAMAHA technology for the creation of sound

fields

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,

DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

Sophisticated AM/FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

◆ Radio Data System capability (U.K. and Europe models only)

HDMI (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or

high-definition video (includes 1080p video signal

transmission) as well as multi-channel digital audio based on

HDMI version 1.2a

◆ Analog video to HDMI digital video up-conversion

(composite video ↔ S-video ↔ component video → HDMI

digital video) capability for monitor out

◆ Analog video up-scaling from 480i (NTSC)/576i (PAL) or

480p/576p to 720p or 1080i

iPod controlling capability

◆ DOCK terminal to connect a YAMAHA iPod universal dock

(such as the YDS-10, sold separately), which supports iPod

(Click and Wheel), iPod nano, and iPod mini

Network features

◆ NETWORK port to connect a PC and YAMAHA MCX-2000

or access the Internet Radio via a LAN

◆ DHCP automatic or manual network configuration

USB features

◆ USB port to connect a USB memory device or a USB portable

audio player

Other features

◆ YPAO (YAMAHA Parametric Room Acoustic Optimizer) for

automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ GUI (graphical user interface) menus that allows you to

optimize this unit to suit your individual audio/video system

◆ GUI display menu language switching capability

(English, Japanese, French, German, Spanish and Russian)

◆ 6 or 8-channel additional input jacks for discrete multi-

channel input

◆ Analog video interlace/progressive conversion from 480i

(NTSC)/576i (PAL) to 480p/576p

◆ S-video signal input/output capability

◆ Component video input/output capability includes (3

COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ Optical and coaxial digital audio signal jacks

◆ Pure Direct mode for pure hi-fi sound for all sources

◆ Cinema and music night listening modes

◆ Compressed Music Enhancer mode to improve the sound

quality of compression artifacts (such as the MP3 format) to

that of a high-quality stereo

◆ Remote control with preset remote control codes, learning,

macro and buttons and display backlight capability

◆ ZONE 2/ZONE 3 custom installation facility

◆ Zone switching capability between the main zone and

ZONE 2/ZONE 3 using ZONE CONTROLS

◆ Zone 2 OSD (on-screen display) capability

◆ Sleep timer

FEATURES

GETTING STARTED

5 En

English

INTRODUCTION

Check that you received all of the following parts.

GETTING STARTED

Supplied accessories

ON

OFF

CLEAR

LEARN

RENAME

MACRO

REC

NET RADIO

USB

PC/MCX

VOLUME

CH

TV VOL

EFFECT

STRAIGHT

MEMORY

A/B/C/D/E

SRCH MODE

PURE DIRECT

PRESET/CH

SET MENU

B

AND

LEVEL

ENHANCER

STEREO

SUR. DECODE

SELECT

EXTD SUR.

CLASSICAL

LIVE/CLUB

ENTERTAIN

MOVIE

NIGHT

MEMORY

1

2

TV

SOURCE

AMP

SELECT

DTV

DVR/VCR 2

VCR 1

DVD

CBL/SAT

MD/TAPE

CD-R

PHONO

TUNER CD

MULTI CH IN

SLEEP

AUDIO SEL

POWER

STANDBY

NET/USB

FREQ/TEXT

EON

MODE PTY SEEK

START

–

2

+

––

+

ENTER

DISPLAY

AUDI O

MENU

TITLE

TV MUTE

TV INPUT

MUTE

4

3

ENT

+

10

0

9

5

1

AV

TV

7

6

8

RETURN

V

-

AUX/DOCK

Remote control

Batteries (6)

(AAA, LR03)

AM loop antenna

Optimizer microphoneSpeaker terminal wrench Power cable

Indoor FM antenna

(U.S.A., Canada, China, Asia, General,

and Korea models)

Indoor FM antenna

(Europe, U.K. and Australia models)

TUNER

CD

CD-R

DTV

NET/USB

CBL/SAT

MD/TAPE

VCR 1

DVD

V-AUX/DOCK

DVR/VCR 2

POWER

STANDBY

A/B/C/D/E

PRESET

VOLUME

ZONE 3

ZONE 2

ID2

ID1

MUTE

Zone 2/Zone 3

remote control

CONTROLS AND FUNCTIONS

6 En

This section describes only the amplifier controls and functions of this unit. See the following pages for details about

other control and functions.

• AM/FM tuning .......................................... see page 56

1 MASTER ON/OFF

Turns this unit on or off (see page 34).

2 MAIN ZONE ON/OFF

Turns on the main zone or sets it to the standby mode

(see page 34).

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control.

• When you turn on this unit, there will be a 4 to 5-second delay

before this unit can reproduce sound.

• This button is operational only when MASTER ON/OFF is

pressed inward to the ON position.

3 INPUT selector

Selects the desired input source (see page 40).

4 AUDIO SELECT

Toggles the priority for the type of audio input jack

between “AUTO”, “HDMI”, “COAX/OPT” and

“ANALOG” when one component is connected to two or

more input jacks (see page 42).

5 TONE CONTROL

Adjusts the bass/treble balance of the front left, front right

and center channels in conjunction with the PROGRAM

selector (see page 52).

6 REC OUT/ZONE2

Selects the input source you want to direct to the audio/

video recorder and Zone 2 outputs independently of the

input source you are listening to or watching in the main

zone (see page 74).

7 STRAIGHT

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing (see

page 51).

CONTROLS AND FUNCTIONS

Front panel

ON/OFF

MASTER

PURE DIRECT

VOLUME

MAIN ZONE

INPUT

ON

OFF

ENHANCER

NIGHT

ZONE ON/OFF

ZONE CONTROLS

MODE

TUNING

PRESET/TUNING

EDIT

MULTI ZONE

FM/AM

PRESET/

TUNING

MAN'L/AUTO FM

MEMORY

MIC

OPTIMIZER

EFFECT

STRAIGHT

CONTROL

SELECT

AUDIO

TONE

REC OUT/

ZONE2

A/B/C/D/E

PROGRAM

YPAO

ZONE 3

R

L

OPTICAL

USB

ZONE 2

AUDIO

VIDEO AUX

SILENT CINEMA

S VIDEO

VIDEO

PHONES

32 BCA09

GHIFED

876541

Notes

CONTROLS AND FUNCTIONS

7 En

INTRODUCTION

English

8 MULTI ZONE buttons

ZONE 2 ON/OFF

Turns on Zone 2 only or sets it to the standby mode

(see page 122).

ZONE 3 ON/OFF

Turns on Zone 3 only or sets it to the standby mode

(see page 122).

These buttons are operational only when MASTER ON/OFF

is pressed inward to the ON position.

ZONE CONTROLS

Switches the zone you want to control between the

main zone, Zone 2 and Zone 3 (see page 122).

y

After you press ZONE CONTROLS, the indicator for the

currently selected zone flashes in the front panel display for

approximately 5 seconds. While the indicator is flashing,

perform the desired operation.

9 Front panel display

Shows information about the operational status of this unit

(see page 12).

0 ENHANCER

Turns on or off the Compressed Music Enhancer mode

(see page 54).

A Remote control sensor

Receives signals from the remote control (see page 11).

B NIGHT

Turns on or off the night listening modes (see page 55).

C PURE DIRECT

Turns on or off the Pure Direct mode (see page 52).

D PROGRAM selector

• Selects sound field programs (see page 46).

• Adjusts the bass/treble balance in conjunction with

TONE CONTROL (see page 52).

E OPTIMIZER MIC jack

Use to connect and input audio signals from the supplied

optimizer microphone in the “Auto Setup” procedure (see

page 35).

F PHONES jack

Outputs audio signals for private listening with

headphones (see page 43).

G VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console or a video camera

(see page 29).

y

To reproduce the source signals input at these jacks, select

“V-AUX” as the input source.

The audio signals input at the DOCK terminal on the rear panel

take priority over the ones input at the VIDEO AUX jacks.

H USB port

Use to connect a USB memory device or a USB portable

audio player (see page 72).

I VOLUME

Controls the output level of all audio channels.

y

This does not affect the AUDIO OUT (REC) level.

■ Opening and closing the front panel

door

When you want to use the controls behind the front panel

door, open the door by gently pressing on the lower part of

the panel. Keep the door closed when not using these

controls.

Note

To open, press gently on the lower part of the panel.

CONTROLS AND FUNCTIONS

8 En

■ Remote control controls and functions

This section describes only the amplifier controls and functions of this unit. See the following pages for details about

other control and functions.

• AM/FM tuning .......................................... see page 56

• Controlling a TV ..................................... see page 109

• Controlling other components ................. see page 110

• Controlling option components ............... see page 111

The operation mode of the remote control buttons in the shaded

area below depends on the operation mode selector position. Set

the operation mode selector to AMP to control this unit.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate (see page 11).

2 TRANSMIT indicator

Flashes while the remote control is sending infrared

signals.

3 Input selector buttons

Select the input source you want to control.

y

The selected input source name appears in the display window on

the remote control showing which source is currently operational.

4 Display window

Shows the name of the selected input source that you can

control.

5 LIGHT

Lights up the remote control buttons and the display

window.

6 LEVEL

Selects the speaker channel to be adjusted and sets the

output level (see page 53).

7 Cursor buttons k / n / l / h, ENTER

Move the items or cursor and adjust the parameters in the

GUI screens or front panel display.

8 Sound field program selector buttons

Select sound field programs (see page 46).

9 SUR. DECODE

Activates decoders to play back 2-channel sources in

surround (see page 75).

0 MEMORY 1/2

Recalls “MEMORY 1” or “MEMORY 2” of “System

Memory” (see page 106).

A Network and USB input selector buttons

Select the sub input source of NET/USB (see page 69).

PC/MCX

Selects a PC server or YAMAHA MCX-2000 as the

sub input source of NET/USB.

Remote control

ON

OFF

CLEAR

LEARN

RENAME

MACRO

REC

NET RADIO

USB

PC/MCX

VOLUME

CH

TV VOL

EFFECT

STRAIGHT

MEMORY

A/B/C/D/E

SRCH MODE

PURE DIRECT

PRESET/CH

SET MENU

B

AN

D

LEVEL

ENHANCER

STEREO

SUR. DECODE

SELECT

EXTD SUR.

CLASSICAL

LIVE/CLUB

ENTERTAIN

MOVIE

NIGHT

MEMORY

1

2

TV

SOURCE

AMP

SELECT

DTV

DVR/VCR 2

VCR 1

DVD

CBL/SAT

MD/TAPE

CD-R

PHONO

TUNER CD

MULTI CH IN

SLEEP

AUDIO SEL

POWER

STANDBY

NET/USB

–

2

+

––

+

ENTER

DISPLAY

AUDIO

MENU

TITLE

TV MUTE

TV INPUT

MUTE

4

3

ENT

+

10

0

9

5

1

AV

TV

7

6

8

RETURN

V

-

AUX/DOCK

FREQ/TEXT

EON

MODE PTY SEEK

START

1

2

3

4

5

6

7

8

9

0

B

C

A

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

U

t

S

R

Note

CONTROLS AND FUNCTIONS

9 En

INTRODUCTION

English

NET RADIO

Selects the Internet radio as the sub input source of

NET/USB.

USB

Selects a USB memory device or a USB portable

audio player as the sub input source of NET/USB.

• Press NET/USB to select “NET/USB” as the input source

before you press any of the network and USB input selector

buttons stated above to select the corresponding sub input

source of NET/USB.

• When you press any of the network and USB input selector

buttons, the contents previously played for the corresponding

sub input source of NET/USB is automatically played.

B MACRO ON/OFF

Turns on or off the macro function (see page 115).

C MACRO

Programs a series of operations to be controlled with a

single button (see page 115).

D STANDBY

Sets the main zone to the standby mode (see page 34).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

E POWER

Turns on the main zone (see page 34).

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

F AUDIO SEL

Toggles the priority for the type of audio input jack

between “AUTO”, “HDMI”, “COAX/OPT” and

“ANALOG” when one component is connected to two or

more input jacks (see page 42).

G SLEEP

Sets the sleep timer (see page 45).

H SELECT k / n

Selects another input source that you can control

independently of the input source selected with the input

selector buttons.

I Operation mode selector

Selects the operation mode of the remote control buttons

in the shaded area.

AMP

Operates the amplifier function of this unit.

SOURCE

Operates the component selected with an input

selector button (see page 110).

TV

Operates the TV assigned to either DTV or PHONO

(see page 109).

• To set the remote control codes for other components, see

page 111.

• When you set the remote control codes for both DTV and

PHONO (see page 111), priority is given to the one set for

DTV.

J VOLUME +/–

Increases or decreases the volume level.

K MUTE

Mutes the audio output. Press again to restore the audio

output to the previous volume level (see page 43).

L PURE DIRECT

Turns on or off the pure direct mode (see page 52).

M SET MENU

Activates the GUI screen (see page 44).

N STRAIGHT

Turns the sound field programs off or on. When the

“STRAIGHT” mode is selected, 2-channel or multi-

channel input signals are output directly from their

respective speakers without effect processing (see

page 51).

O EXTD SUR.

Switches between 5.1 and 6.1/7.1-channel playback of

multi-channel sources (see page 75).

P SELECT

Selects decoders for 2-channel sources (see pages 75 and

76).

Q ENHANCER

Turns on or off the Compressed Music Enhancer mode

(see page 54).

R NIGHT

Turns on or off the night listening modes (see page 55).

S RENAME

Changes the name of the input source in the display

window (see page 114).

T CLEAR

Clears remote control functions acquired from the learn,

macro and/or rename features (see page 118).

U LEARN

Programs remote control codes of functions from other

remote controls (see page 113).

Notes

Note

Notes

CONTROLS AND FUNCTIONS

10 En

This section describes the function of each control on the

Zone 2/Zone 3 remote control used to control the amplifier

functions of Zone 2 or Zone 3.

See the following pages for details about other controls

and functions.

• AM/FM tuning ........................................ see page 56

1 Input selector buttons

Select the desired input source of Zone 2 or Zone 3.

2 ID1/ID2 switch

Switches the remote control ID between ID1 and ID2

(see page 112).

3 POWER

Turns on Zone 2 or Zone 3.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

4 STANDBY

Sets Zone 2 or Zone 3 to the standby mode.

This button is operational only when MASTER ON/OFF on the

front panel is pressed inward to the ON position.

5 VOLUME +/–

Increases or decreases the volume level of Zone 2 or

Zone 3.

6 MUTE

Mutes the sound of Zone 2 or Zone 3. Press again to

restore the audio output to the previous volume level.

7 ZONE 2/ZONE 3 switch

Switches between the operation mode of Zone 2 and that

of Zone 3.

Zone 2/Zone 3 remote control

TUNER

CD

CD-R

DTV

NET/USB

CBL/SAT

MD/TAPE

VCR 1

DVD

V-AUX/DOCK

DVR/VCR 2

POWER

STANDBY

A/B/C/D/E

PRESET

VOLUME

ZONE 3

ZONE 2

ID2

ID1

MUTE

2

7

6

5

4

3

1

Note

CONTROLS AND FUNCTIONS

11 En

INTRODUCTION

English

■ Installing batteries in the remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert the four supplied batteries

(AAA, LR03) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Slide the cover back until it snaps into place.

■ Installing batteries in the Zone 2/Zone 3

remote control

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, LR03)

according to the polarity markings

(+ and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the TRANSMIT indicator does not flash or its light becomes

dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• We recommend using alkaline batteries.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries, set up the remote control code

and program any acquired functions that may have been

cleared.

■ Using the remote control

The remote control transmits a directional infrared ray.

Be sure to aim the remote control directly at the remote

control sensor on this unit during operation.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

Preparing the remote control

1

3

2

1

3

2

Notes

30 30

Approximately 6 m

Remote control sensor

CONTROLS AND FUNCTIONS

12 En

1 HDMI indicator

Lights up when the signal of the selected input source is

input at HDMI IN 1, HDMI IN 2 or HDMI IN 3 jacks

(see page 21).

2 RECOUT indicator

Lights up when this unit is in the recording input source

selecting mode (see page 74).

3 DOCK indicator

Lights up when you station your iPod in a YAMAHA iPod

universal dock (such as the YDS-10, sold separately)

connected to the DOCK terminal of this unit

(see page 29).

4 Battery charge indicator

Lights up when this unit charges the battery of the

stationed iPod in the standby mode of this unit (see

page 66).

5 Input source indicators

The corresponding cursor lights up to show the currently

selected input source.

6 VOLUME level indicator

Indicates the current volume level.

7 MUTE indicator

Flashes while the MUTE function is on (see page 43).

8 Multi-information display

Shows the name of the current sound field program and

other information when adjusting or changing settings.

9 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

0 Input channel and speaker indicators

Input channel indicators

Indicate the channel components of the current digital

input signal.

Presence and surround back speaker

indicators

Light up according to the number of presence and

surround back speakers set for “Presence” (see

page 97) and “Surround Back” (see page 97) in

“Speaker Set” when “Test Tone” in “Basic” is set to

“ON” (see page 96).

y

You can make settings for the presence and surround back

speakers automatically by running “Auto Setup” (see page 35) or

manually by adjusting settings for “Presence” (see page 97) and

“Surround Back” (see page 97) in “Speaker Set”.

Front panel display

CD-R

CD

PHONO

MULTI CH

TUNER

MD/TAPE

DVD

DTV

MUTE

VOLUME

dB

LFE

LL C R

SL SB SR

RECOUT

HiFi DSP

DIGITAL

EX

PL x

MP3

WMA

DSD

PCM

VIRTUAL

YPAO

ENHANCER

MATRIX

DISCRETE

CINEMA

SILENT

24

96

96/24

TUNED

STEREO

AUTO

MEMORY

PS

ZONE2

ZONE3

SLEEP

PTY HOLD

PTY

RT

CT

EON

NIGHT

NET/USB

DOCK

VCR 1

CBL/SAT

DVR/VCR 2

V-AUX

DSD

PCM

TUNED

STEREO

AUTO

MEMORY

PS

ZONE2

ZONE3

SLEEP

PTY HOLD

PTY

RT

CT

EON

NIGHT

HiFi DSP

DIGITAL

EX

PL x

VIRTUAL

YPAO

ENHANCER

MATRIX

DISCRETE

CINEMA

SILENT

24

96

MP3

WMA

J

I

H

G

F

C

B

A

O

N

M

L

K

0

98

765431

2

E

D

O........ U.K. and Europe models only

Presence speaker indicators

Input channel indicators

Surround back speaker indicators

L CR

SL SB SR

LFE

CONTROLS AND FUNCTIONS

13 En

INTRODUCTION

English

A DSP indicators

The respective indicator lights up when any of the DSP

sound field programs are selected.

CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound

field program (see page 47).

HiFi DSP indicator

Lights up when you select a HiFi DSP sound field

program (see page 47).

B VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 51).

C YPAO indicator

Lights up when you run “Auto Setup” and when the

speaker settings set in “Auto Setup” are used without any

modifications (see page 35).

D ENHANCER indicator

Lights up when the Compressed Music Enhancer mode is

turned on (see page 54).

E Signal format indicators

The respective indicator lights up when this unit is

reproducing DSD (Direct Stream Digital), PCM (Pulse

Code Modulation), WMA (Windows Media Audio), WAV

(RIFF Wave Form Audio) or MP3 (MPEG-1 Audio Layer-

3) audio signals.

F Dolby decoder indicators

The respective indicator lights up when any of the Dolby

decoders of this unit function.

G Sound field indicators

Light up to indicate the active DSP sound fields.

H Headphones indicator

Lights up when headphones are connected (see page 43).

I SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 51).

J DTS decoder indicators

The respective indicator lights up when any of the DTS

decoders of this unit function.

K Tuner indicators

Lights up when this unit is in the FM or AM tuning mode.

TUNED indicator

Lights up when this unit is tuned into a station

(see page 56).

STEREO indicator

Lights up when this unit is receiving a strong signal

for an FM stereo broadcast while the AUTO indicator

is lit (see page 56).

AUTO indicator

Lights up when this unit is in the automatic tuning

mode (see page 56).

MEMORY indicator

Flashes to show that a station can be stored

(see page 59).

L ZONE2/ZONE3 indicators

Lights up when Zone 2 or Zone 3 is turned on

(see page 122).

M NIGHT indicator

Lights up when you select a night listening mode

(see page 55).

N SLEEP indicator

Lights up while the sleep timer is on (see page 45).

O Radio Data System indicators

(U.K. and Europe models only)

PS, PTY, RT and CT

Light up according to the selected Radio Data System

display mode.

EON

Lights up when the EON data service is being

received.

PTY HOLD

Lights up while searching for the Radio Data System

stations in the PTY SEEK mode.

Presence DSP sound field

Listening position

Surround left

DSP sound field

Surround right

DSP sound field

Surround back DSP sound field

CONTROLS AND FUNCTIONS

14 En

1 COMPONENT VIDEO jacks

See pages 23 and 24 for connection information.

20 Audio component jacks

See page 26 for connection information.

3 Video component jacks

See pages 23 and 24 for connection information.

4 ANTENNA terminals

See page 31 for connection information.

5 WRENCH HOLDER

Use to hook the supplied speaker terminal wrench when

not in use (see page 18).

6 VOLTAGE SELECTOR

(Asia and General models only)

See page 32 for details.

7 AC IN/OUTLET(S)

See page 32 for connection information.

8 HDMI connectors

See page 21 for connection information.

9 REMOTE jacks

See page 121 for details.

A DOCK terminal

See page 29 for connection information.

B NETWORK port

Use to connect a network cable for network connections.

See page 30 for connection information.

C DIGITAL INPUT/OUTPUT jacks

See page 24 for connection information.

D CONTROL OUT jack

This is a control expansion terminal for custom

installation.

E RS-232C terminal

This is a control expansion terminal for factory use only.

Consult your dealer for details.

F Speaker terminals

See page 16 for connection information.

G MULTI CH INPUT jacks

See page 28 for connection information.

H PRE OUT jacks

See page 27 for connection information.

I ZONE OUT jacks

See page 121 for connection information.

Rear panel

AC IN

AC OUTLETS

HOLDER

WRENCH

SPEAKERS

CENTER

BI-AMP

PRESENCE

SURROUND BACK/

SP1

FRONT

SURROUND

SINGLE

ANTENNA

FM

GND

AM

VIDEO

S VIDEO

MONITOR OUT

VIDEO

COMPONENT VIDEO

REMOTE

PHONO

GND

CD

IN(PLAY)

OUT(REC)

CD-R

HDMI

AUDIO

DOCK

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

CONTROL OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

ZONE

VIDEO

CD

DV

D

DVR/

VCR2

COAXIAL

1

2

CD

DVD

DTV

CBL/

SAT

MD/

TAP E

CD-R

OPTICAL

987

65

4

321

SB(8CH)

DTV

TAP E

MD/

(REC)

(PLAY)

IN

OUT

DVD

DVR/VCR 2

VCR 1

CBL/SAT

OUT

IN

DVD

DTV

CBL/SAT

MONITOR OUT

Y

P

R

PR

PB

P

B

IN

OUT

1

2

IN

OUT

IN1

CBL/

SAT

IN2

IN3

OUT

+

A B

C

R

L

R

L

R

L

SP2

NETWORK

DTV

DVD

MULTI CH INPUT

PRE OUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

ZONE

VIDEO

SB(8CH)

7654321

IGH

FCDEB

A08 9

CONNECTIONS

15 En

English

PREPARATION

The speaker layout below shows the speaker setting we

recommend. You can use it to enjoy CINEMA DSP and

multi-channel audio sources.

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Place the

center speaker centrally between the front speakers and as

close to the monitor as possible, such as directly over or

under it.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m above the

floor.

Surround back left and right speakers

(SBL and SBR)

The surround back speakers supplement the surround

speakers and provide more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm apart.

Ideally, they should be positioned at the same width as that

of the front speakers.

Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the front

speakers with extra ambient effects produced by CINEMA

DSP (see page 144). These effects include sounds that

filmmakers intend to locate a little farther back behind the

screen in order to create more theater-like ambience. Place

these speakers at the front of the room about 0.5 to 1 m

outside the front speakers, facing slightly inward, and about

1.8 m above the floor.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the YAMAHA Active Servo Processing Subwoofer

System, is effective not only for reinforcing bass

frequencies from any or all channels, but also for high

fidelity sound reproduction of the LFE (low-frequency

effect) channel included in Dolby Digital and DTS

sources. The position of the subwoofer is not so critical,

because low bass sounds are not highly directional. But it

is better to place the subwoofer near the front speakers.

Turn it slightly toward the center of the room to reduce

wall reflections.

CONNECTIONS

Placing speakers

SW

FR

PR

PL

FL

SBR

SBL

SL

SR

C

60˚

30˚

PL

PR

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

FR

PRPL

C

FL

1.8 m

30 cm or more

1.8 m

0.5 to 1 m 0.5 to 1 m

16 En

CONNECTIONS

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass.

• Before connecting the speakers, make sure that this unit is turned off (see page 34).

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this

unit. This could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still creates interference with the

monitor, place the speakers away from the monitor.

• If you are to use 6 ohm speakers, be sure to set “SPEAKER IMP.” to “6ΩMIN” before using this unit

(see page 33). 4 ohm speakers can be also used as the front speakers (see page 126).

• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the

plain cable to the “–” (black) terminals.

• The low-frequency signals of other speakers set to “Small” or to “None” in “Speaker Set” (see pages 96 and 97) are directed to the

speakers selected in “Bass Out” (see page 98).

• You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. You can set

to prioritize either set of speakers using the “PR/SB Priority” parameter in “Speaker Set” (see page 98).

• You can use the PRESENCE terminals to connect the Zone 2 or Zone 3 speakers as well as the presence speakers (see page 121).

Connecting speakers

Notes

CAUTION

SPEAKERS

CENTER

BI-AMP

PRESENCE

SURROUND BACK/

SP1

FRONT

SURROUND

SINGLE

PRE OUT

SUB

WOOFER

+

R

L

SP2

Front speakers

Surround speakers

Presence speakers

Subwoofer

Right

Left

Center speaker

Surround back speakers

Right

Left

Right

Zone 2 or Zone 3

speakers

(see page 121)

17 En

CONNECTIONS

English

PREPARATION

FRONT terminals

Connect front left and right speakers to these terminals.

CENTER terminals

Connect a center speaker to these terminals.

SURROUND terminals

Connect surround left and right speakers to these

terminals.

SURROUND BACK terminals

Connect surround back left and right speakers to these

terminals.

When you use a surround back speaker, connect the speaker to the

left SURROUND BACK terminal (SINGLE).

PRESENCE terminals

Connect presence left and right speakers to these

terminals.

SUBWOOFER jack

Connect a subwoofer with a built-in amplifier (such as the

YAMAHA Active Servo Processing Subwoofer System)

to this jack.

■ Connecting the speaker cable

1 Remove approximately 10 mm of insulation

from the end of each speaker cable and then

twist the exposed wires of the cable together

to prevent short circuits.

2 Loosen the knob using the supplied speaker

terminal wrench.

3 Insert one bare wire into the hole on the side

of each terminal.

4 Tighten the knob to secure the wire using the

supplied speaker terminal wrench.

Note

10 mm

Speaker terminal wrench

Red: positive (+)

Black: negative (–)

18 En

CONNECTIONS

5 Hook the speaker terminal wrench onto the

WRENCH HOLDER on the rear panel of this

unit when not in use.

■ Connecting to the SP2 speaker

terminals

Connect Zone 2 or Zone 3 speakers to these terminals (see

page 121).

1 Open the tab.

2 Insert one bare wire into the hole on the

terminal.

3 Close the tab to secure the wire.

■ Connecting the banana plug

(except U.K., Europe, Asia and Korea

models)

The banana plug is a single-pole electrical connector

widely used to terminate speaker cables.

1 Tighten the knob using the supplied speaker

terminal wrench.

2 Insert the banana plug connector into the

end of the corresponding terminal.

y

You can also use the banana plug with the SP2 speaker terminals.

Open the tab and then insert one banana plug into the hole on the

terminal. Do not close the tab after connecting the banana plug.

Red: positive (+)

Black: negative (–)

Banana plug

Red: positive (+)

Black: negative (–)

Speaker terminal wrench

Pagina se încarcă ...

Yamaha RX-V2700 Manualul proprietarului

Yamaha RX-V2700 Manualul proprietarului

în alte limbi

Lucrări conexe

Alte documente