Ubiquiti RocketDish LW RD-5G30-LW Ghid de inițiere rapidă

Marca: Ubiquiti

Model: RocketDish LW RD-5G30-LW

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

airMAX

2x2 PtP Bridge

Dish Antenna

Model: RD-5G30-LW

Introduction

Thank you for purchasing the Ubiquiti Networks® RocketDish

™

an airMAX® 2x2 PtP Bridge Dish Antenna. This Quick Start

Guide is designed to guide you through the installation of the

antenna. This Quick Start Guide also includes the warranty

terms and is for use with the RocketDish, modelRD-5G30-LW.

Package Contents

Dish Antenna Mounting

Bracket

Antenna Feed Lower Pole

Bracket

Upper Pole

Bracket

Support Arm Brace Screws

(M6, Qty. 4)

Protective

Shroud

Hex Head Bolts

(M8, Qty. 5)

Lock Washers

(M8, Qty. 5)

Flat Washers

(M8, Qty. 5)

Stabilizer Brackets

(Qty. 2)

airMAX

2x2 PtP Bridge

Dish Antenna

Model: RD-5G30-LW

M10x100 Bolts

(Qty. 2)

Serrated

Flange Nuts

(M10, Qty. 2)

M8x150 Carriage

Bolts (Qty. 4)

Pole Clamps

(Qty. 2)

Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• Rocket

™

5ac PtP, Rocket5ac Lite, RocketM5 Titanium, or

RocketM5 (sold separately)

• Phillips screwdriver

• 13 mm wrench

• Wrench or channel lock pliers with 63.5 mm (2.5") capacity

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Overview

Fully Assembled Back View

Mounting Bracket

Pole Clamp

Protective Shroud

Stabilizer Brackets

Pole Clamp

Elevation Rod

Installation

Important: Handle the Dish Reflector with care.

Deformations in its shape may reduce the RocketDish's

effectiveness.

1. Line up the alignment tabs of the Mounting Bracket with

the alignment slots of the Dish Reflector. Insert the tabs and

rotate the Mounting Bracket until they lock intoplace.

Note: Ensure that the antenna feed slot of the

Mounting Bracket lines up with the antenna feed slot

of the Dish Reflector, as shown below:

2. The Dish Reflector and Antenna Feed are keyed so the

Antenna Feed can only be installed in a single orientation.

Follow these steps:

a. Remove the knob from the Antenna Feed.

b. Line up the alignment pins of the Antenna Feed with

the alignment holes of the Dish Reflector and Mounting

Bracket.

Note: Ensure that the straight edge of the

Antenna Feed end (shown below) and arrow on

the Antenna Feed cap are pointing straight up.

c. Insert the Antenna Feed.

3. To secure the Antenna Feed to the Dish Reflector:

a. Replace the knob and tighten it by hand until the knob

touches the surface of the Mounting Bracket.

b. Use a wrench or channel lock pliers to tighten the knob

an additional ¼ turn. Do NOT over-tighten the knob.

Note: Ensure that the Antenna Feed is securely

attached by the knob.

Important: Do not handle the RocketDish by the Antenna

Feed once the feed is attached.

*640-00148-03*

640-00148-03

4. Attach the Rocket to the Mounting Bracket.

a. Align the mounting tabs on the back of the Rocket with

the Rocket mount.

b. Slide the Rocket down to lock it into place.

5. Attach the other end of the RF Cables to the RF connectors

on the Rocket in this combination: H to Chain 1 and V to

Chain 0. Then slide the jackets over the RF connectors to

protect them.

6. Attach the Protective Shroud.

a. Align the hash mark on the top of the shroud with the

notch on the Dish Antenna.

b. Rotate the shroud clockwise until it locks into place.

7. Attach two Hex Head Bolts, two Lock Washers, and two Flat

Washers to the bottom of the Mounting Bracket. Ensure that

there is a gap of 8 mm between each Flat Washer and the

Mounting Bracket.

Note: Ensure that each Lock Washer is always

installed between the Hex Head Bolt and Flat Washer.

Hex Head Bolt

Flat Washer

Lock Washer

8 mm

8. Attach the horizontal slot of the Support Arm to the Upper

Pole Bracket using a Hex Head Bolt, Lock Washer, and

FlatWasher.

Note: Ensure that the degree settings are the same

on both arms of the Upper Pole Bracket.

Degree markings

facing outward

9. Attach the Brace to the pole brackets using the four Screws.

10. Each M8x150 Carriage Bolt includes a serrated flange nut.

Remove these and use them in the next step.

11. Attach one Pole Clamp to each pole bracket.

a. Insert two M8x150 Carriage Bolts into each pole bracket.

b. Slide the hole of a Pole Clamp over one bolt of each

pole bracket.

c. Place one serrated flange nut on each bolt.

12. Attach the Stabilizer Brackets to the pole just beneath the

area where the RocketDish will be attached.

Note: The pole-bracket assembly can accommodate

a Ø 38 - 101mm pole.

a. Place one Stabilizer Bracket on each side of the pole.

b. Insert the two M10x100 Bolts into the Stabilizer Brackets.

c. Secure each bolt with one Serrated Flange Nut.

50 N-m

13. Attach the pole-bracket assembly to the pole:

a. Slide the slot of each Pole Clamp over the

corresponding M8x150 CarriageBolt.

b. Tighten the serrated flange nuts of the bolts to secure

the pole-bracket assembly to the pole.

Proper slot orientation

25 N-m

14. Lift the Dish Reflector and align the two lower Hex Head

Bolts with the slots on the Lower Pole Bracket. Seat the bolts

in the slots.

15. Attach each arm of the Upper Pole Bracket to the Mounting

Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.

16. Before adjusting the tilt angle, ensure that the six Hex Head

Bolts are loose enough to allow movement.

IMPORTANT: If you cannot spin the washers freely by

hand, then loosen the Hex Head Bolts until you can.

17. To adjust the tilt angle, turn the screw head of the Elevation

Rod until the desired tilt is reached.

18. Lock the alignment by tightening all six Hex HeadBolts to

25 N-m.

Specifications

RocketDish RD-5G30-LW

Dimensions 650 x 650 x386 mm (25.6 x 25.6 x 15.2")

Weight 7.4 kg (16.31 lb)

(Mount Included)

Frequency 5.1 - 5.9 GHz

Gain 30 dBi

Max. VSWR 1.6:1

Wind Survivability 200 km/h (125 mph)

Wind Loading 790 N @ 200 km/h (178 lbf @ 125 mph)

Polarization Dual Linear

F/B Ratio 30 dB

ETSI Specication EN 302 326 DN2

Mounting Universal Pole Mount, Rocket Bracket, and

Weatherproof RF Jumpers Included

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

RF Exposure Warning

The antenna and transmitter must be installed to provide a separation

distance from all persons and must not be located or operating in

conjunction with any other antenna or transmitter. For the specific

separation distance, refer to the Quick Start Guide for your Rocket device

(transmitter).

L’antenne et l’émetteur doit être installé pour fournir une distance de

séparation de toute les personnes et ne doit pas être situé ou opérant en

conjonction avec une autre antenne ou un autre émetteur. Pour la distance

spécifique de séparation, se référer au Guide de démarrage rapide pour

votre appareil Rocket (l’émetteur).

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Pagina se încarcă ...

Ubiquiti RocketDish LW RD-5G30-LW Ghid de inițiere rapidă

Marca: Ubiquiti

Model: RocketDish LW RD-5G30-LW

Categorie: Antene de rețea

Tip: Ghid de inițiere rapidă

Descărcați PDF

raport

în alte limbi

English: Ubiquiti RocketDish LW RD-5G30-LW Quick start guide
italiano: Ubiquiti RocketDish LW RD-5G30-LW Guida Rapida

Ubiquiti RocketDish LW RD-5G30-LW Ghid de inițiere rapidă

Ubiquiti RocketDish LW RD-5G30-LW Ghid de inițiere rapidă

în alte limbi

Lucrări conexe