Yamaha RX-V675 Manualul proprietarului

Categorie
Receptoare AV
Tip
Manualul proprietarului

Acest manual este potrivit și pentru

English
Français
Deutsch
Svenska
Italiano
Español
Nederlands
AV Receiver/Ampli-tuner audio-vidéo
G
Easy Setup Guide
Manuel de configuration rapide
Anleitung zur Schnelleinrichtung
Snabbinstallationsguide
Guida di configurazione rapida
Guía de configuración sencilla
Easy Setup-gids
En 1
Check that the following accessories are supplied with the product.
The following cables (not supplied) are required to build the system described in this
document.
Speaker cables (depending on the number of speakers)
HDMI cable (x2)
Audio pin cable (x1)
Digital optical cable (x1)
(not required if your TV supports ARC [Audio Return Channel])
1 Preparation
Accessories
Remote control Batteries
(AAA, R03, UM-4) (x2)
Insert the batteries the right way round.
AM antenna FM antenna YPAO microphone
CD-ROM
(Owner’s Manual)
Safety Brochure Easy Setup Guide
The illustrations of the main unit and remote control used in this guide are of the RX-V775 (U.S.A.
model), unless otherwise specified.
*The supplied FM antenna
varies depending on the
region of purchase.
Cables required for connections
Easy Setup Guide
English
AV Receiver
This document explains how to set up a 5.1- or 7.1-channel system and
play back surround sound from a BD/DVD on the unit.
To reduce the impact on natural resources, the Owners Manual for this product is
supplied on CD-ROM. For more information about this product, refer to the
Owners Manual on the supplied CD-ROM.
PDF versions of this guide and “Owners Manual” can be downloaded from the
following website.
http://download.yamaha.com/
[For U.S. customers only]
Visit the following website for additional information, FAQ’s, downloads such as
“Owner’s Manual” and product updates.
http://usa.yamaha.com/support/
2 En
Set up the speakers in the room using the following diagram as a reference.
For information on other speaker systems, refer to “Owner’s Manual”.
1 Front speaker (L)
2 Front speaker (R)
3 Center speaker
4 Surround speaker (L)
5 Surround speaker (R)
6 Surround back speaker (L)
7 Surround back speaker (R)
9 Subwoofer
2 Placing speakers
5.1-channel system
12
39
45
10° to 30°10° to 30°
7.1-channel system
45
1
2
39
67
30 cm (1 ft) or more
10° to 30° 10° to 30°
En 3
Connecting speaker cables
Speaker cables have two wires. One is for connecting the
negative (–) terminals of the unit and the speaker, and the
other is for the positive (+) terminals. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive terminals.
a Remove approximately 10
mm (3/8”) of insulation
from the ends of the
speaker cable and twist
the bare wires of the cable
firmly together.
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side
(upper right or bottom left) of the terminal.
d Tighten the terminal.
Using a banana plug
(U.S.A., Canada, China,
Australia and General
models only)
a Tighten the speaker
terminal.
b Insert a banana plug into the end of the terminal.
1
Connect the front speakers (1/2)
to the FRONT (//\) terminals.
2
Connect the center speaker (3) to the
CENTER terminal.
3 Connecting speakers/subwoofer
Under its default settings, the unit is configured for 8-ohm
speakers. When connecting 6-ohm speakers, set the unit’s
speaker impedance to “6 Ω MIN”. For details, see “Setting the
speaker impedance” in “Owner’s Manual”.
Use a subwoofer equipped with built-in amplifier.
Before connecting the speakers, remove the unit’s power cable
from the AC wall outlet and turn off the subwoofer.
Ensure that the core wires of the speaker cable do not touch
each other or come into contact with the unit’s metal areas. This
may damage the unit or the speakers. If the speaker cables
short circuit, “Check SP Wires” will appear on the front display
when the unit is turned on.
The illustrations of the unit (rear) used in this section are of the
RX-V775.
FRONT
aa
b
d
c
– (black)
+ (red)
FRONT
a
b
Banana plug
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
The unit (rear)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
The unit (rear)
4 En
3
Connect the surround speakers
(4/5) to the SURROUND (//\)
terminals.
4
Connect the subwoofer (9) to the
SUBWOOFER PRE OUT (1) jack.
Use a subwoofer equipped with built-in amplifier.
Connect the surround back speakers
(6/7) to the SURROUND BACK (//\)
terminals.
FRONT CENTER SURROUND
SINGLE
SURROUND BACK BI-AMP
SPEAKERS
SUBWOOFER
ZONE2/F PRESENCE
EXTRA SP
2
12
3
45
9
The unit (rear)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
Audio pin cable
The unit (rear)
For 7.1-channel system
FRONT CENTER SURROUND
SI GLE
SURROUND BACK/BI AMP
SPEAKERS
SUBWOOFER
ZONE2/F PRESENCE
EXTRA SP
1
2
12
3
45
9
67
The unit (rear)
En 5
4 Connecting external devices
AUD O 1
AUD O 2
O TI AL
O TI AL
C AXI L
V DEO
AV4
AV3
AV2
AV 1
(TV)
P
B
Y
P
COMPO ENT
V DEO
V DEO
MONITOR OUT
P
B
Y
P
R
HDM HDMI 2 HDMI 3 HDMI 4 HDMI 5
BD D
V
12
ARC
ANTENNA
FM
AM
FRONT CENTER SURROUND
S NGLE
SURROUND BACK B -AMP
SPEAKERS
AV 5
V D O
AV 6
AV OUT
ZO E OU
UBWOOF R
SUR BACKS RROUND
FRONT
PRE OUT
CENTER
S LE
ONE 2
NETWORKDC OUT
REMOTE
V
A
(
NET
)
IN
UT
ZONE2 F PRESENCE
EXTRA SP
COM ONENT V DEO
CENTER
2
HDM
UT
(
RADIO
)
INFOZONE 2
ZONE CONTROL
MEMORY
PR SET
FM AM
TUN NG
CONTROL
TV
BD
DVD
NET
AD O
INPUT
SCENE
MAIN ZONE
PHONES
S LENT
CINEMA
STRAIGHT
VIDEO
PURE D RECT
HDMI/
V 2 1A
V DEO
VOLU ME
AUX
ONE
PROGRAM
YPAO M C
MHL V 1A
OPT CAL
AV4
(TV)
HDMIOPTICAL
HDMI
HDMI
HDMI HDMI
HDMI
O
O
a
c
b
d
H I 1
( )
HDMI OUT
ARC
12
220V
-
240V
110V
-
120V
VOLTAGE SELECTOR
TV
Audio out
(optical)
HDMI in HDMI out
BD/DVD player
HDMI
OUT
jack
HDMI 1 jack
AV 4 (OPTICAL) jack
The unit (rear)
To an AC wall
outlet
Turn on the unit
The unit (front)
VOLTAGE SELECTOR
(General model only)
1
Connect external devices to the unit.
a Connect a BD/DVD player to the unit with an HDMI
cable.
If the BD/DVD player is currently connected to the
TV directly with an HDMI cable, disconnect the
cable from the TV and connect it to this unit.
b Connect a TV to the unit with the other HDMI cable.
c Connect a TV to the unit with a digital optical cable.
This connection is required to play back TV audio
on the unit. This connection is not required if your
TV supports ARC (Audio Return Channel).
d Connect the power cable to an AC wall outlet.
For information on how to connect radio antennas or other
external devices, see “PREPARATIONS” in “Owner’s Manual”.
2
Turn on the unit, the TV and the BD/DVD
player.
3
Use the TV remote control to change the
TV input to video from the unit.
The connections are complete. Proceed to the next
page to optimize the speaker settings.
By connecting a TV to the unit with an HDMI cable, you can
configure the unit’s settings with the menu displayed on the TV. In
addition, you can select the on-screen menu language from English
(default), Japanese, French, German, Spanish, Russian, Italian and
Chinese. For details, refer to “Owner’s Manual”. In this guide,
illustrations of English menu screens are used as examples.
Before connecting the power cable (General model only)
Make sure you set the switch position of
VOLTAGE SELECTOR according to your local voltage.
Voltages are AC 110-120/220-240 V, 50/60 Hz.
6 En
The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the
distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as
volume balance and acoustic parameters, to suit your room.
Preparing for YPAO
5
Optimizing the speaker settings automatically (YPAO)
TV L TV CH
TV
NPUT
MUTE
CODE SET
10
ENT
MEMORY
5
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN
OPT ON
TOP MENU
MUTE
PROGRAM VOLUME
POP UP/MENU
PURE DIRECT
STRAIGHT
NFO SLEEP
MUS C
NET
PARTY HDMI OUT
TUNER
MA N
ZONE 2
USB
MODE
SCENE
BD
DV
TV
NET
RADIO
SOURCE
RECEIVER
HDMI
AV
AUDIO
5
65
V AUX
SUR DECODE
TV
VO
L
TV
C
H
NP
U
T
MUTE
CO
DE
S
ET
9
0
10
ENT
M
EM
O
RY
5
6
8
1 2
3
4
MO
VI
E
E
NHANC
E
R
T
U
NIN
G
PRE
S
ET
BAND
DI
S
PLA
Y
O
N
S
CREE
N
O
PT
O
N
T
OP MENU
M
UTE
P
R
OG
RA
M
V
O
L
U
ME
P
O
P UP
/
MEN
U
PURE DIRECT
S
TRAI
GH
T
NF
O
S
LEE
P
MUS C
NE
T
PART
Y
HDMI OU
T
TUNER
MA N
ZO
NE
2
U
SB
M
O
DE
SC
EN
E
BD
DV
D
TV
NET
RADI
O
SO
UR
C
E
HDMI
AV
A
U
DI
O
5
6
5
V
A
UX
1
2
3
4
1
2
1
2
3
4
SU
R DE
CO
D
E
RECEIVER
Cursor keys
ENTER
RETURN
During the measuring process, test tones are output at high volume. Ensure that the test
tones do not frighten small children. Also, refrain from using this function at night when it
may be a nuisance to others.
During the measuring process, you cannot adjust the volume.
During the measuring process, keep the room as quiet as possible.
Do not connect headphones.
Do not stand between the speakers and the YPAO microphone during the measurement
process (about 3 minutes).
Move to the corner of the room or leave the room.
YPAO MIC
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
The unit (front)
Place the YPAO microphone at your
listening position (same height as your
ears). We recommend the use of a
tripod as a microphone stand. You can
use the tripod screws to fix the
microphone in place.
YPAO microphone
Ear height
Turn on the subwoofer and set
the volume to half. If the
cross-over frequency is
adjustable, set it to maximum.
1
Connect the YPAO microphone to the
YPAO MIC jack on the front panel.
The following screen appears on the TV.
To cancel the operation, disconnect the YPAO microphone
before starting the measurement.
2
To start the measurement, use the cursor
keys to select “Measure” and press
ENTER.
The measurement will start in 10 seconds.
The following screen appears on the TV when
the measurement finishes.
If the cursor keys do not work, press RECEIVER and then use
the cursor keys.
If any error message (such as E-1) or warning message (such
as W-2) appears, see “Error messages” or “Warning
messages” in “Owner’s Manual”.
If the warning message “W-1:Out of Phase” appears, see
“If “W-1:Out of Phase” appears” (next page).
En 7
3
Use the cursor keys to select
Save/Cancel” and press ENTER.
4
Use the cursor keys to select “SAVE” and
press ENTER.
5
Disconnect the YPAO microphone from the
unit.
This completes optimization of the speaker settings.
Follow the procedure below to check the speaker
connections.
a Use the cursor keys to select “Result” and press ENTER.
b Use the cursor keys to select “Wiring”.
c Check the cable connections (+/–) of the speaker that
was identified as being “Reverse” in the warning
message.
If the speaker is connected correctly:
Depending on the type of speakers or room
environment, this message may appear even if the
speakers are connected correctly.
In this case, you can ignore the message.
Press RETURN and proceed to step 3.
If the speaker is connected incorrectly:
Turn off the unit, reconnect the speaker cable, and then
try YPAO measurement again.
The YPAO microphone is sensitive to heat, so should not be
placed anywhere where it could be exposed to direct sunlight or
high temperatures (such as on top of AV equipment).
If “W-1:Out of Phase” appears
8 En
Now let’s play back a BD/DVD.
We recommend playing back multichannel audio
(5.1-channel or more) to feel surround sound produced
by the unit.
1
Press HDMI 1 to select “HDMI 1” as the
input source.
2
Start playback on the BD/DVD player.
3
Press STRAIGHT repeatedly to select
STRAIGHT”.
4
Press VOLUME to adjust the volume.
This completes the basic setup procedure.
Sound is only being output from the front speakers
during multichannel audio playback
Check the digital audio output setting on the BD/DVD
player.
It may be set to 2-channel output (such as PCM).
No sound is coming from a specific speaker
See “Troubleshooting” in “Owner’s Manual”.
6 Playing back a BD/DVD
TV L TV CH
TV
NPUT
MUTE
CODE SET
10
ENT
MEMORY
5
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN
OPTION
TOP MENU
MUTE
PROGRAM VOLUME
POP UP/MENU
PURE DIRECT
STRA GHT
NFO SLEEP
MUS C
NET
PARTY HDMI OUT
TUNER
MA N
ZONE 2
USB
MODE
SCENE
BD
DV
TV
NET
RADIO
SOURCE
RECEIVER
HDMI
AV
AUDIO
5
65
V AUX
1
SUR DECOD
TV
VO
L
TV
C
H
NP
U
T
MUTE
CO
DE
S
ET
9
0
10
ENT
M
EM
O
RY
5
6
8
1 2
3
4
MO
VI
E
E
NHANC
E
R
T
U
NIN
G
PRE
S
ET
BAND
DI
S
PLA
Y
RETURN
ENTE
R
O
N
S
CREE
N
O
PTI
O
N
T
OP MENU
M
UTE
P
R
OG
RA
M
P
O
P UP
/
MEN
U
PURE DIRECT
NF
O
S
LEE
P
MUS C
NE
T
PART
Y
HDMI OU
T
TUNER
MA N
ZO
NE
2
U
SB
M
O
DE
SC
EN
E
BD
DV
D
TV
NET
RADI
O
SO
UR
C
E
R
E
C
EIVE
R
HDMI
AV
A
U
DI
O
5
6
5
V
A
UX
1
2
1
2
3
4
SU
R DE
CO
D
HDMI 1
STRAIGHT
VOLUME
If surround sound is not working
SW
C
L
SL SR
R
HDMI1
VOL
SW
C
L
SL SR
R
VOL
STRAIGHT
SW
C
L
SL SR
R
Volume -30.0dB
VOL
Many more features!
The unit has various other functions.
Please refer to “Owner’s Manual” on the supplied
CD-ROM to help you get the most out of the unit.
Connecting other playback
devices
Connect audio devices (such as CD player),
game consoles, camcorders, and many others.
Selecting the sound mode
Select the desired sound program (CINEMA
DSP) or surround decoder suitable for movies,
music, games, sports programs, and other uses.
Playing back from iPod
By using a USB cable supplied with iPod, you
can enjoy iPod music on the unit.
Listening to FM/AM radio
Playing back music stored on
a USB storage device
Playing back the network
contents
Selecting the input source and
favorite settings at once
For more information, see “What you can do
with the unit”.
Fr 1
Vérifiez que les accessoires suivants sont fournis avec le produit.
Les câbles suivants (non fournis) sont requis pour l’installation du système décrit dans
le présent document.
Câbles d’enceintes (en fonction du nombre d’enceintes)
Câble HDMI (x2)
Câble de broche audio (x1)
Câble optique numérique (x1)
(inutile si votre téléviseur prend en charge la fonction ARC
[Audio Return Channel])
1 Préparation
Accessoires
Télécommande Piles
(AAA, R03, UM-4) (x2)
Insérez les piles comme indiqué.
Antenne AM Antenne FM Microphone YPAO
CD-ROM
(Mode d’emploi)
Brochure sur la sécurité Manuel de configuration rapide
* L’antenne FM fournie
dépend de la région
d’achat.
Les illustrations de l’unité principale et de la télécommande utilisées dans ce guide représentent le
modèle RX-V775 (modèle pour les États-Unis), sauf avis contraire.
Câbles requis pour les raccordements
Ampli-tuner audio-vidéo
Ce document décrit la configuration d’un système à 5.1 ou 7.1 voies
et explique comment restituer le son d’ambiance d’un disque BD/DVD
sur l’unité.
Afin de préserver l’environnement, le Mode d’emploi de ce produit est fourni
sur CD-ROM. Pour en savoir plus sur ce produit, reportez-vous au Mode
d’emploi fourni sur CD-ROM
.
Pour télécharger ce guide ainsi que le « Mode d’emploi » au format PDF,
rendez-vous sur le site Web suivant :
http://download.yamaha.com/
Manuel de
configuration rapide
Français
2 Fr
Installez les enceintes dans la pièce en vous reportant au diagramme suivant.
Pour obtenir des informations sur les autres systèmes d’enceinte, consultez le « Mode d’emploi ».
1 Enceinte avant (G)
2 Enceinte avant (D)
3 Enceinte centrale
4 Enceinte Surround (G)
5 Enceinte Surround (D)
6 Enceinte Surround arrière (G)
7 Enceinte Surround arrière (D)
9 Subwoofer
2 Installation des enceintes
Système à 5.1 voies
12
39
45
10° à 30°10° à 30°
Système à 7.1 voies
45
1
2
39
67
30 cm ou plus
10° à 30° 10° à 30°
Fr 3
Raccordement des câbles d’enceinte
Les câbles d’enceinte sont composés de deux fils. L’un
se connecte aux bornes négatives (-) de l’appareil et de
l’enceinte, et l’autre aux bornes positives (+). Si les fils
sont de couleurs différentes afin d’éviter toute
confusion, connectez le fil de couleur noire aux bornes
négatives et l’autre fil aux bornes positives.
a Dénudez les extrémités
du câble d’enceinte sur
environ 10 mm, puis
torsadez fermement les
brins dénudés du câble.
b Desserrez la borne
d’enceinte.
c Insérez les fils dénudés du câble dans l’écartement sur le
côté (supérieur droit ou inférieur gauche) de la borne.
d Serrez la borne.
Utilisation d’une fiche
banane
(Modèles standard et
destinés aux États-Unis,
au Canada, à la Chine et
à l’Australie uniquement)
a Serrez la borne d’enceinte.
b Insérez la fiche banane dans l’extrémité de la borne.
1
Raccordez les enceintes avant
(1/2) aux bornes FRONT (//\).
2
Raccordez l’enceinte centrale (3) à la
borne CENTER.
3 Raccordement des enceintes/du caisson de graves
L’unité est configurée pour des enceintes 8 ohms par défaut.
Lorsque vous raccordez des enceintes 6 ohms, réglez
l’impédance d’enceinte de l’unité sur « 6 Ω MIN ». Pour plus
d’informations, reportez-vous à la section « Réglage de
l’impédance des enceintes » du « Mode d’emploi ».
Utilisez un caisson de graves équipé d’un amplificateur intégré.
Avant de raccorder les enceintes, retirez le câble d’alimentation
de l’unité de la prise secteur et éteignez le caisson de graves.
Veillez à ce que les fils conducteurs du câble de l’enceinte ne
se touchent pas ou n’entrent pas en contact avec les parties
métalliques de l’unité. Ce contact risque d’endommager l’unité ou
les enceintes. Si un court-circuit survient au niveau des câbles de
l’enceinte, le message « Check SP Wires » apparaît sur
l’afficheur de la face avant lors de la mise sous tension de l’unité.
Les illustrations de l’unité (arrière) utilisées dans cette section
sont celles du modèle RX-V775.
FRONT
aa
b
d
c
– (noir)
+ (rouge)
FRONT
a
b
Fiche banane
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
L’unité (arrière)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
L’unité (arrière)
4 Fr
3
Raccordez les enceintes d’ambiance
(4/5) aux bornes SURROUND
(//\).
4
Raccordez le subwoofer (9) à la prise
SUBWOOFER PRE OUT (1).
Utilisez un subwoofer équipé d’un amplificateur intégré.
Raccordez les enceintes surround arrière
(6/7) aux bornes SURROUND BACK
(//\).
FRONT CENTER SURROUND
SINGLE
SURROUND BACK BI-AMP
SPEAKERS
SUBWOOFER
ZONE2/F PRESENCE
EXTRA SP
2
12
3
45
9
L’unité (arrière)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
2
12
3
45
9
Câble de broche audio
L’unité (arrière)
Pour le système à 7.1 voies
FRONT CENTER SURROUND
SI GLE
SURROUND BACK/BI AMP
SPEAKERS
SUBWOOFER
ZONE2/F PRESENCE
EXTRA SP
1
2
12
3
45
9
67
L’unité (arrière)
Fr 5
4 Raccordement des appareils externes
AUD O 1
AUD O 2
O TI AL
O TI AL
C AXI L
V DEO
AV4
AV3
AV2
AV 1
(TV)
P
B
Y
P
COMPO ENT
V DEO
V DEO
MONITOR OUT
P
B
Y
P
R
HDM HDMI 2 HDMI 3 HDMI 4 HDMI 5
BD D
V
12
ARC
ANTENNA
FM
AM
FRONT CENTER SURROUND
S NGLE
SURROUND BACK B -AMP
SPEAKERS
AV 5
V D O
AV 6
AV OUT
ZO E OU
UBWOOF R
SUR BACKS RROUND
FRONT
PRE OUT
CENTER
S LE
ONE 2
NETWORKDC OUT
REMOTE
V
A
(
NET
)
IN
UT
ZONE2 F PRESENCE
EXTRA SP
COM ONENT V DEO
CENTER
2
HDM
UT
(
RADIO
)
INFOZONE 2
ZONE CONTROL
MEMORY
PR SET
FM AM
TUN NG
CONTROL
TV
BD
DVD
NET
AD O
INPUT
SCENE
MAIN ZONE
PHONES
S LENT
CINEMA
STRAIGHT
VIDEO
PURE D RECT
HDMI/
V 2 1A
V DEO
VOLU ME
AUX
ONE
PROGRAM
YPAO M C
MHL V 1A
OPT CAL
AV4
(TV)
HDMIOPTICAL
HDMI
HDMI
HDMI HDMI
HDMI
O
O
a
c
b
d
H I 1
( )
HDMI OUT
ARC
12
220V
-
240V
110V
-
120V
VOLTAGE SELECTOR
Téléviseur
Sortie audio
(optique)
Entrée HDMI Sortie HDMI
Lecteur BD/DVD
Prise
HDMI OUT
Prise HDMI 1
Prise AV 4
(OPTICAL)
L’unité (arrière)
Branchement
sur une prise
secteur
Mettre l’unité
sous tension
L’unité (avant)
VOLTAGE SELECTOR
(Modèles Standard
uniquement)
1
Raccordez les appareils externes à l’unité.
a Raccordez un lecteur BD/DVD à l’unité au moyen
d’un câble HDMI.
Si le lecteur BD/DVD est actuellement directement
raccordé au téléviseur à l’aide d’un câble HDMI,
débranchez ce câble du téléviseur et raccordez-le
à cette unité.
b Raccordez un téléviseur à l’unité au moyen de
l’autre câble HDMI.
c Raccordez un téléviseur à l’unité au moyen d’un
câble optique numérique.
Ce raccordement est nécessaire si vous souhaitez
restituer le son TV sur l’unité. Ce raccordement
n’est pas nécessaire si votre téléviseur prend en
charge la fonction ARC (Audio Return Channel).
d Raccordez le câble d’alimentation à une prise
électrique murale.
Pour plus d’informations sur le raccordement des antennes
radio ou des autres appareils externes, reportez-vous à la
section « PRÉPARATION » du « Mode d’emploi ».
2
Mettez sous tension, l’unité, le téléviseur
et le lecteur BD/DVD.
3
Utilisez la télécommande du téléviseur pour
changer la source d’entrée du téléviseur et
afficher l’image à partir de l’unité.
Les raccordements sont terminés. Passez à la page
suivante pour optimiser les réglages des enceintes.
Lorsque le téléviseur est raccordé à l’unité par un câble HDMI, vous
pouvez configurer les réglages de cette dernière à l’aide du menu
qui s’affiche sur le téléviseur. Par ailleurs, vous pouvez sélectionner
la langue souhaitée dans le menu affiché à l’écran parmi les langues
suivantes : anglais (par défaut), japonais, français, allemand,
espagnol, russe, italien et chinois. Pour plus d’informations,
reportez-vous au « Mode d’emploi ». Des illustrations d’écrans de
menus anglais sont utilisées comme exemples dans ce guide.
Avant de raccorder le câble d’alimentation (modèle
standard uniquement)
Vérifiez que vous sélectionnez la position de permutation de
VOLTAGE SELECTOR en fonction de la tension locale. Les
tensions sont CA 110-120/220-240 V, 50/60 Hz.
6 Fr
La fonction Yamaha Parametric room Acoustic Optimizer (YPAO) permet de détecter les raccordements des enceintes et de
mesurer la distance entre ces dernières et la position d’écoute. Elle optimise ensuite automatiquement les réglages des
enceintes tels que les paramètres d’équilibre du volume et les paramètres acoustiques qui conviennent à la pièce.
Préparation à la fonction YPAO
5
Optimisation automatique des réglages d’enceintes
(YPAO)
Lors de la mesure, des signaux test sont restitués à un volume élevé. Assurez-vous que
le signal test n’effraie pas les jeunes enfants. Évitez également d’utiliser cette fonction la
nuit, où elle peut constituer une nuisance pour les autres.
Lors de la mesure, vous ne pouvez pas régler le volume.
Faites en sorte que la pièce soit le plus calme possible.
Ne raccordez pas d’écouteurs.
Ne restez pas entre les enceintes et le microphone YPAO pendant la mesure (environ
3 minutes).
Placez-vous dans un coin de la pièce ou quittez-la.
YPAO MIC
VOLUME HIGH CUT
CROSSOVER/
MIN MAXMIN MAX
L’unité (avant)
Placez le microphone YPAO à votre
position d’écoute (à hauteur d’oreilles).
Nous conseillons l’utilisation d’un trépied
comme support de microphone. Lorsque
vous utilisez un trépied, utilisez les vis du
trépied pour fixer le microphone.
Microphone YPAO
Hauteur
d’oreille
Allumez le caisson de graves
et réglez le volume à moitié.
Si la fréquence de coupure
est réglable, réglez-la sur le
maximum.
1
Raccordez le microphone YPAO à la prise
YPAO MIC sur le panneau avant.
L’écran suivant apparaît sur le téléviseur.
Pour annuler l’opération, débranchez le microphone YPAO
avant le début de l’opération de mesure.
2
Pour commencer la mesure, utilisez les
touches de curseur pour sélectionner
« Measure » et appuyez sur ENTER.
La mesure commence dans les 10 secondes.
Lorsque la mesure est terminée, l’écran suivant
apparaît sur le moniteur TV.
Si les touches de curseur ne fonctionnent pas, appuyez sur
RECEIVER puis utilisez les touches de curseur.
Si un message d’erreur (par exemple E-1) ou d’avertissement
(par exemple W-2) apparaît, reportez-vous aux sections
« Messages d’erreur » ou « Messages d’avertissement » du
« Mode d’emploi ».
Si le message d’avertissement « W-1:Out of Phase » apparaît,
reportez-vous à la section « Si le message « W-1:Out of
Phase » apparaît » se trouvant à la page suivante.
TV L TV CH
TV
NPUT
MUTE
CODE SET
10
ENT
MEMORY
5
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN
OPTION
TOP MENU
MUTE
PROGRAM VOLUME
POP UP MENU
PURE DIRECT
STRA GHT
NFO SLEEP
MUSIC
NET
PARTY HDMI OUT
TUNER
MA N
ZONE 2
USB
MODE
SCENE
BD
DV
TV
NET
RADIO
SOURCE
RECE VER
HDMI
AV
AUDIO
5
65
V AUX
SUR DECODE
TV
VO
L
TV
C
H
TV
NP
U
T
MUTE
CO
DE
S
ET
9
0
10
ENT
M
EM
O
RY
5
6
8
1 2
3
4
MO
VI
E
E
NHANC
E
R
T
U
NIN
G
PRE
S
ET
BAND
DI
S
PLA
Y
O
N
S
CREE
N
O
PTI
O
N
T
OP MENU
M
UTE
P
R
OG
RA
M
V
O
L
U
ME
P
O
P UP MEN
U
PURE DIRECT
S
TRA
GH
T
NF
O
S
LEE
P
MUS
I
C
NE
T
PART
Y
HDMI OU
T
TUNER
MA N
ZO
NE
2
U
SB
M
O
DE
SC
EN
E
BD
DV
D
TV
NET
RADI
O
SO
UR
C
E
HDMI
AV
A
U
DI
O
5
6
5
V
A
UX
1
2
3
4
1
2
1
2
3
4
SU
R DE
CO
D
E
RECEIVER
Touches de
curseur
ENTER
RETURN
Fr 7
3
Utilisez les touches de curseur pour
sélectionner « Save/Cancel » et appuyez
sur ENTER.
4
Utilisez les touches de curseur pour
sélectionner « SAVE » et appuyez sur
ENTER.
5
Débranchez le microphone YPAO de
l’unité.
L’optimisation des réglages d’enceintes est
maintenant terminée.
Suivez la procédure ci-dessous pour vérifier les
raccordements de l’enceinte.
a Utilisez les touches de curseur pour sélectionner
« Result » et appuyez sur ENTER.
b Utilisez les touches de curseur pour sélectionner
«Wirin.
c Vérifiez les raccordements de câble (+ et -) de l’enceinte
désignée par « Inversé » dans le message
d’avertissement.
Si l’enceinte est correctement raccordée :
Selon le type d’enceintes ou l’environnement, ce
message peut apparaître, même si les enceintes
sont correctement raccordées.
Dans ce cas, vous pouvez ignorer le message.
Appuyez sur RETURN et passez à l’étape 3.
Si l’enceinte n’est pas correctement raccordée :
Mettez l’unité hors tension et raccordez à nouveau le
câble d’enceinte, puis essayez à nouveau d’effectuer
la mesure YPAO.
Le microphone YPAO est sensible à la chaleur. Ne le placez
pas dans un endroit où il pourrait être exposé directement
à la lumière du soleil ou à des températures élevées (sur un
équipement AV, etc.).
Si le message « W-1:Out of Phase » apparaît
8 Fr
Voyons maintenant comment lire un disque BD/DVD.
Pour sentir les effets d’ambiance sonore produits par
l’unité, nous vous recommandons de lire les disques
avec le système audio multivoies (5.1 voies et plus).
1
Appuyez sur HDMI 1 pour sélectionner
« HDMI 1 » comme source d’entrée.
2
Commencez la lecture sur le lecteur BD/DVD.
3
Appuyez à plusieurs reprises sur STRAIGHT
pour sélectionner « STRAIGHT ».
4
Appuyez sur VOLUME pour régler le volume.
La procédure d’installation de base est maintenant
terminée.
Lors de la lecture à l’aide du système audio multivoies,
le son est restitué uniquement par les enceintes avant
Vérifiez le réglage de la sortie audio numérique du
lecteur BD/DVD.
Il est peut-être réglé pour restituer un son à 2 voies
(PCM par exemple).
Une enceinte spécifique n’émet aucun son
Reportez-vous à la section « Guide de dépannage » du
« Mode d’emploi ».
6 Lecture d’un disque BD/DVD
TV L TV CH
TV
NPUT
MUTE
CODE SET
10
ENT
MEMORY
5
MOVIE
ENHANCER
TUNING PRESET
BAND
DISPLAYRETURN
ENTER
ON
SCREEN
OPTION
TOP MENU
MUTE
PROGRAM VOLUME
POP UP/MENU
PURE DIRECT
STRA GHT
NFO SLEEP
MUS C
NET
PARTY HDMI OUT
TUNER
MA N
ZONE 2
USB
MODE
SCENE
BD
DV
TV
NET
RADIO
SOURCE
RECEIVER
HDMI
A
UDIO
5
65
V AUX
1
SUR DECOD
TV VO
T
L
V
CH
TV
NPU
T
MU
T
E
CODE SET
9
0
1
0
ENT
MEM
O
RY
5
6
8
1
2
3
4
M
O
VI
E
ENHAN
CE
R
T
U
NIN
G
P
RE
S
ET
BAND
DI
S
PLA
Y
RETURN
ENTE
R
ON
SC
REE
N
O
PTI
ON
TO
P MEN
U
MUTE
PR
OG
RAM
PO
P
U
P
/
MEN
U
P
U
RE DIRE
CT
NF
O
S
LEE
P
M
US C
N
ET
PARTY
HDMI
OUT
TUNER
MA N
ZO
NE
2
US
B
MO
D
E
SCEN
E
BD
DV
D
TV
NE
T
RADI
O
SOURC
E
RECEIVE
R
H
DM
I
A
V
A
UDI
O
5
6
5
V AUX
1
2
1
2
3
4
SU
R DE
CO
D
HDMI 1
STRAIGHT
VOLUME
Si le système de son d’ambiance ne
fonctionne pas
SW
C
L
SL SR
R
HDMI1
VOL
SW
C
L
SL SR
R
VOL
STRAIGHT
SW
C
L
SL SR
R
Volume -30.0dB
VOL
Encore plus de
fonctions !
L’unité propose diverses autres fonctions.
Reportez-vous au « Mode d’emploi » sur le
CD-ROM fourni pour savoir comment utiliser
l’unité de manière optimale.
Raccordement d’autres
appareils de lecture
Raccordez des appareils audio (lecteurs CD et
autres), consoles de jeux, caméscopes, etc.
Sélection du mode sonore
Sélectionnez le programme sonore souhaité
(CINEMA DSP) ou le décodeur d’ambiance qui
convient aux films, à la musique, aux jeux, aux
programmes sportifs, etc.
Écoute de musique à partir
d’un iPod
Grâce au câble USB fourni avec l’iPod, vous
pouvez écouter votre musique sur l’unité.
Écoute d’émission FM/AM
Lecture de musique stockée sur
un dispositif de stockage USB
Lecture de contenus réseau
Sélection simultanée de la source
et des paramètres favoris
Pour plus d’informations, reportez-vous à la
section « Fonctions de l’unité ».
De 1
Prüfen Sie, ob das folgende Zubehör im Lieferumfang des Produkts enthalten ist.
Die folgenden Kabel (nicht mitgeliefert) sind erforderlich, um das in diesem Dokument
beschriebene System aufzubauen.
Lautsprecherkabel (je nach Anzahl der Lautsprecher)
HDMI-Kabel (x 2)
Audio-Cinchkabel (x 1)
Optisches Digitalkabel (x 1)
(nicht erforderlich, wenn Ihr Fernseher ARC unterstützt [Audio
Return Channel
])
1 Vorbereitung
Zubehör
Fernbedienung Batterien
(AAA, R03, UM-4) (x 2)
Setzen Sie die Batterien in der
richtigen Ausrichtung ein.
AM-Antenne FM-Antenne YPAO-Mikrofon
CD-ROM
(Bedienungsanleitung)
Sicherheitsbroschüre Anleitung zur
Schnelleinrichtung
Die Abbildungen des Hauptgeräts und der Fernbedienung in dieser Anleitung stammen vom
US-amerikanischen Modell des RX-V775.
* Je nach Erwerbsort ist die
mitgelieferte FM-Antenne
unterschiedlich ausgeführt.
Erforderliche Anschlusskabel
Anleitung zur
Schnelleinrichtung
Deutsch
AV-Receiver
Dieses Dokument beschreibt, wie ein 5.1- oder 7.1-Kanal-System
eingerichtet und Surround-Sound von BD/DVD über das Gerät
wiedergegeben wird.
Um die Umwelt zu schonen, wird die Bedienungsanleitung für dieses Produkt auf
CD-ROM ausgeliefert. Weitere Einzelheiten über dieses Produkt finden Sie in der
Bedienungsanleitung auf der beiliegenden CD-ROM.
PDF-Versionen dieser Anleitung zur Schnelleinrichtung sowie der
„Bedienungsanleitung“ können von der folgenden Website heruntergeladen
werden.
http://download.yamaha.com/
2 De
Stellen Sie die Lautsprecher im Raum auf, während Sie sich an der folgenden Abbildung orientieren.
Informationen zu anderen Lautsprechersystemen entnehmen Sie bitte der „Bedienungsanleitung“.
1 Front-Lautsprecher (L)
2 Front-Lautsprecher (R)
3 Center-Lautsprecher
4 Surround-Lautsprecher (L)
5 Surround-Lautsprecher (R)
6 Hinterer Surround-Lautsprecher (L)
7 Hinterer Surround-Lautsprecher (R)
9 Subwoofer
2 Aufstellen der Lautsprecher
5.1-Kanal-System
12
39
45
10° bis 30°10° bis 30°
7.1-Kanal-System
45
1
2
39
67
mindestens 30 cm
10° bis 30°
10° bis 30°
De 3
Anschließen der Lautsprecherkabel
Lautsprecherkabel haben zwei Adern. Eine davon wird
am negativen (–) Anschluss von Gerät und Lautsprecher
angeschlossen, die andere am positiven (+) Anschluss.
Wenn die Adern farbkodiert sind, um Verwechslungen zu
verhindern, sollten Sie die schwarz gefärbte Ader an der
negativen Polklemme und die andere Ader an der
positiven Polklemme anschließen.
a Entfernen Sie vom Ende
jedes Lautsprecherkabels
circa 10 mm der
Isolierung, und verdrehen
Sie die Metallfäden der
blanken Litze möglichst
fest miteinander.
b Lösen Sie die
Lautsprecherklemme.
c Führen Sie die blanke Litze des Lautsprecherkabels in
die seitliche Öffnung (oben rechts oder unten links) der
Klemme ein.
d Ziehen Sie die Klemme fest.
Verwenden eines
Bananensteckers
(nur US-amerikanisches,
kanadisches, chinesisches,
australisches und
Universalmodell)
a Ziehen Sie die
Lautsprecherklemme fest.
b Stecken Sie einen Bananenstecker in die Öffnung an der
Schraubklemme.
1
Schließen Sie die Front-Lautsprecher
(1/2) an den Buchsen FRONT
(//\) an.
2
Schließen Sie den Center-Lautsprecher
(3) an der Buchse CENTER an.
3 Anschließen von Lautsprechern und Subwoofer
Das Gerät ist werksseitig für 8-Ohm-Lautsprecher konfiguriert.
Beim Anschluss von 6-Ohm-Lautsprechern stellen Sie die
Lautsprecherimpedanz-Einstellung auf „6 Ω MIN“ ein. Näheres
siehe unter „Einstellen der Lautsprecherimpedanz” in der
„Bedienungsanleitung“.
Verwenden Sie einen Subwoofer mit integriertem Verstärker.
Bevor Sie die Lautsprecher anschließen, trennen Sie das
Netzkabel des Geräts von der Netzspannungsversorgung,
und schalten Sie den Subwoofer aus.
Achten Sie darauf, dass die Leitungsadern des Lautsprecherkabels
nicht einander berühren und auch nicht mit metallenen Bereichen
am Gerät in Kontakt kommen. Dadurch könnten das Gerät oder
die Lautsprecher beschädigt werden. Im Fall eines Kurzschlusses
der Lautsprecherkabel wird die Meldung „Check SP Wires“ auf dem
Frontblende-Display angezeigt, wenn das Gerät einschaltet wird.
Die Abbildungen des Geräts (Rückseite) in diesem Abschnitt
stammen vom RX-V775.
FRONT
aa
b
d
c
– (Schwarz)
+ (Rot)
FRONT
a
b
Bananenstecker
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
1
2
12
3
45
9
Gerät (Rückseite)
FRONT CENTER SURROUND
SINGLE
SURROUND BACK B -AMP
SPEAKERS
SUBWOOFER
ZONE2 F PRESENCE
XTRA SP
1
12
3
45
9
Gerät (Rückseite)
1 / 1

Yamaha RX-V675 Manualul proprietarului

Categorie
Receptoare AV
Tip
Manualul proprietarului
Acest manual este potrivit și pentru