Sonicare HX9192/01 Manual de utilizare

FlexCare Platinum Connected

1

2

3

5

6

4

7

8

10

11

12

15

13

14

9

1

English 6

Čeština 22

Eesti 39

Hrvatski 55

Latviešu 72

Lietuviškai 89

Magyar 106

Polski 124

Română 143

Shqip 161

Slovenščina 176

Slovensky 192

Srpski 209

Български 223

Македонски 243

Українська 259

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully

benefit from the support that Philips offers, register your product at

www.philips.com/welcome.

Important safety information

Read this important information carefully before you use the

appliance and save it for future reference.

Danger

-

Keep the charger away from water. Do not

place or store it over or near water

contained in a bathtub, washbasin, sink etc.

Do not immerse the charger in water or any

other liquid. After cleaning, make sure the

charger is completely dry before you

connect it to the mains.

Warning

-

The mains cord cannot be replaced. If the

mains cord is damaged, discard the charger.

-

Always have the charger replaced with one

of the original type in order to avoid a

hazard.

-

Do not use the charger outdoors or near

heated surfaces.

6

English

-

If the appliance is damaged in any way

(brush head, toothbrush handle or charger),

stop using it. This appliance contains no

serviceable parts. If the appliance is

damaged, contact the Consumer Care

Center in your country (see chapter

'Warranty and support').

-

This appliance can be used by children aged

from 8 years and above and by persons with

reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and if they

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children unless they are older than 8 and

supervised.

Caution

-

Do not clean the brush head, the handle,

the charger, the charger cover and/or the

sanitizer in the dishwasher.

7

English

-

If you have had oral or gum surgery in the

previous 2 months, consult your dentist

before you use the toothbrush.

-

Consult your dentist if excessive bleeding

occurs after using this toothbrush or if

bleeding continues to occur after 1 week of

use.Also consult your dentist if you

experience discomfort or pain when you use

the Philips Sonicare.

-

The Philips Sonicare toothbrush complies

with the safety standards for

electromagnetic devices. If you have a

pacemaker or other implanted device,

contact your physician or the device

manufacturer of the implanted device prior

to use.

-

If you have medical concerns, consult your

doctor before you use the Philips Sonicare.

-

This appliance has only been designed for

cleaning teeth, gums and tongue. Do not

use it for any other purpose. Stop using the

appliance and contact your doctor if you

experience any discomfort or pain.

8

English

-

The Philips Sonicare toothbrush is a

personal care device and is not intended for

use on multiple patients in a dental practice

or institution.

-

Stop using a brush head with crushed or

bent bristles. Replace the brush head every

3 months or sooner if signs of wear appear.

-

Do not use other brush heads than the ones

recommended by the manufacturer.

-

If your toothpaste contains peroxide, baking

soda or bicarbonate (common in whitening

toothpastes), thoroughly clean the brush

head with soap and water after each

use.This prevents possible cracking of the

plastic.

-

Do not insert objects into the air openings of

the sanitizer or block these air openings by

placing it on a soft surface or in a position or

location where objects will block these

openings (examples of objects: magazine,

tissue paper and hair).

9

English

-

The UV light bulb is hot during and

immediately after the sanitizing cycle. Do

not touch the UV light bulb when it is hot.

-

Do not operate the sanitizer without the

protective screen in place to avoid contact

with a hot bulb.

-

If the sanitizer has been used for 3

consecutive UV clean cycles (i.e. 3 times in a

row), switch it off for at least 30 minutes

before you start another UV clean cycle.

-

Discontinue use of the sanitizer if the UV

light bulb remains on when the door is

open. UV light can be harmful to the human

eye and skin. Keep the sanitizer out of the

reach of children at all times.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

General description (Fig. 1)

1 Hygienic travel cap

2 Brush head with unique identifier

3 Handle

4 Sensors

5 Power on/off button

6 Bluetooth

7 Intensity level indicator

10

English

8 Intensity level button (+ and -)

9 Brushing modes

10 Mode button

11 Battery level indicator

12 UV sanitizer with integrated charger and cord wrap (select models)

- Not shown: UV light bulb

- Not shown: Sanitizer drip tray

- Not shown: Protective screen for UV light bulb

13 Power cord with plug

14 Charger cover with brush head holders (select models)

15 Travel charger

- Not shown: Travel case

Note: The content of the box may vary based on the model

purchased.

Preparing for use

Attaching the brush head

1 Align the brush head so the bristles point in the same direction as

the front of the handle (Fig. 2).

2 Firmly press the brush head down onto the metal shaft until it

stops (Fig. 3).

Note: Philips Sonicare brush heads are imprinted with icons to easily

identify your brush head (Fig. 4).

Charging the appliance

1 Put the plug of the charger or sanitizer in a wall socket.

2 Place the handle on the charger.

The flashing light of the battery level indicator indicates that the

toothbrush is charging (Fig. 5).

Note: It takes at least 24 hours to fully charge the battery.

11

English

Using the appliance

Bluetooth connectivity

Before you start the connectivity procedure, make sure your mobile

device runs on Bluetooth 4.0 or higher.

Note: For the latest information on device compatibility, please

visit the App Store or Google Play.

Connecting your toothbrush

1 When used in connected mode, the Philips Sonicare app gives you

the opportunity to receive real-time feedback on brushing, store

and share brushing data with your dentist (if you so choose), and

receive personalized coaching. If you wish to use the toothbrush in

unconnected mode, the toothbrush will still function. To use the

toothbrush in connected mode, please follow the instructions

below.

2 Download the Philips Sonicare app from the Apple App Store or

Google Play Store.

3 Confirm Bluetooth is switched on on your mobile device before

you open the app. Check the settings on your mobile device to

switch on Bluetooth.

4 To connect the toothbrush to the app, switch on

thetoothbrushby pressing either the power on/off button or the

brushing mode button. Make sure thetoothbrush is not on the

charger when you switch it on.

5 Open the Sonicare app.

6 Follow the Sonicare app instructions displayed on your mobile

device. The app automatically connects with the toothbrush. If the

toothbrush does not connect, follow the troubleshooting steps

provided in the app.

Note: For optimal data capture, keep your mobile device close during

brushing.

Brushing instructions

1 Wet the bristles and apply a small amount of toothpaste.

12

English

2 Place the toothbrush bristles against the teeth at a slight angle (45

degrees), pressing firmly to make the bristles reach the gumline or

slightly beneath the gumline (Fig. 6).

Note: Keep the center of the brush in contact with the teeth at all

times.

3 Press the power on/off button to turn on the Philips Sonicare.

4 Apply light pressure to maximize Philips Sonicare’s effectiveness

and let the Philips Sonicare toothbrush do the brushing for you.

Do not scrub.

5 Gently move the brush head slowly across the teeth in a small

back and forth motion so the longer bristles reach between your

teeth. Continue this motion throughout the brushing cycle.

6 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing

strokes on each tooth (Fig. 7).

Note: To make sure you brush evenly throughout the mouth,

divide your mouth into 6 sections using the BrushPacer feature

(see chapter ‘Features’).

7 Follow the Sonicare app's brushing guidance combined with the

BrushPacer and begin brushing in section 1 (upper right teeth) and

brush for 20 seconds before you move to section 2 (upper front

teeth). Continue doing this for section 3 till 6 to ensure even

brushing in all 6 segments of the mouth (Fig. 8).

Note: When using the White mode, two additional 20 second

intervals can be used for polishing your front teeth.

8 The Philips Sonicare app helps to address any missed spots by

guiding you to spend 20 seconds in the areas you missed during

brushing.

Your Philips Sonicare toothbrush is safe to use on:

- Braces (brush heads wear out sooner when used on braces)

- Dental restorations (fillings, crowns, veneers)

Note: Ensure that braces or dental restorations are properly adhered

and not compromised. If not, braces or dental restorations may be

damaged when they come into contact with the brush head.

13

English

Note: When the Philips Sonicare toothbrush is used in clinical studies,

the handle should be fully charged and the Easy-start feature

deactivated.

Brushing modes

Note: When the toothbrush is switched on, you cannot toggle

between modes.

1 Prior to turning on the Sonicare, press the mode button to toggle

between modes.

- The selected brushing mode illuminates.

- Once a brushing mode has been selected, it remains active until

another brushing mode is selected.

Clean mode

Standard mode for superior teeth cleaning.

White mode

2 minutes of alternating between White and Massage, with an

additional 40 seconds to polish your visible front teeth.

Deep Clean

Provides an invigorating of deep massage to deliver an exceptionally

clean experience.

Intensity levels per mode

- Low: 1 LED indicator light.

- Medium: 2 LED indicator lights.

- High: 3 LED indicator lights.

Note: to adjust the intensity level to the next higher or lower level, you

can press the + button to increase intensity or the - button to

decrease intensity at any time during the brushing cycle.

Pressure Sensor

A change in vibration (and a slight change in sound) alerts you when

you apply too much pressure while brushing. See chapter ‘Features’.

Battery status (when handle is not on charger)

- 1 yellow LED indicates a low charge.

- 3 green LEDs indicate a full charge.

14

English

Note: If you hear two sets of five beeps and the yellow LED of the

battery level indicator flashes, your Sonicare will turn off until placed

on the charger, where it will start to recharge.

Note: Your Sonicare will not be able to run a brushing routine until it is

fully recharged.

Note:To keep the battery fully charged at all times, you may keep

your Sonicare on the charger when not in use.

Features

Pressure Sensor

This Philips Sonicare model comes with the Pressure Sensor feature

activated. The Pressure Sensor works in all 3 modes and at all 3

intensity levels.

Activating or deactivating the Pressure Sensor feature

1 Attach the brush head to the handle.

2 Place the handle in the plugged-in charger or sanitizer.

- To deactivate Pressure Sensor:

Press and hold the power on/off and mode button for 2 seconds.

You hear 1 beep to indicate that the Pressure Sensor feature has

been deactivated.

- To activate Pressure Sensor:

Press and hold the power on/off and mode button for 2 seconds.

You hear 2 beeps to indicate that the Pressure Sensor feature has

been activated.

BrushPacer

- The BrushPacer is an interval timer that has a short beep and

pause to remind you to brush the 6 sections of your mouth.

Depending on the brushing mode or brushing routine you have

selected, the BrushPacer beeps at different intervals during the

brushing cycle. See the ‘Brushing instructions’ sections (Fig. 8).

To deactivate or reactivate the BrushPacer feature:

1 Place the handle with a brush head attached in the plugged-in

charger.

2 Press and hold the mode button until:

15

English

a You hear 1 beep to indicate the BrushPacer has been

deactivated.

b You hear 2 beeps to indicate the BrushPacer has been

activated.

Smartimer

The Smartimer indicates that your brushing cycle is complete by

automatically turning off the toothbrush at the end of the brushing

cycle.

Dental professionals recommend brushing no less than 2 minutes

twice a day.

Easy-start

This Philips Sonicare comes with the Easy-start deactivated.

The Easy-start feature gently increases the power over the first 14

brushings to help you get used to the brushing with the Philips

Sonicare.

Note: Each of the first 14 brushings must be at least 1 minute in length

to properly advance through the Easy-start ramp-up cycle.

Activating or deactivating the Easy-start feature

1 Attach the brush head to the handle.

2 Place the handle in the plugged-in charger or sanitizer.

- To activate Easy-start:

Press and hold the power on/off and mode button for 2 seconds.

You hear 2 beeps to indicate that the Easy-start feature has been

activated.

- To deactivate Easy-start:

Press and hold the power on/off and mode button for 2 seconds.

You hear 1 beep to indicate that the Easy-start feature has been

deactivated.

Note: Using the Easy-start feature beyond the initial ramp-up period

is not recommended and reduces Philips Sonicare effectiveness in

removing plaque.

Note: Each of the first 14 brushings must be at least 1 minute in length

to properly move through the Easy-start ramp-up cycle.

16

English

Sanitizing

- In addition to rinsing your brush head with water and air drying,

you can clean your brush head with the UV sanitizer for optimal

cleanliness (Fig. 9).

Note: The UV sanitizer is not a replacement for rinsing your brush

head with water, but is additive to rinsing with water.

Unplug the sanitizer, discontinue use and call Consumer Care if:

- The UV light bulb remains on when the door is open.

- The window is broken or missing from the sanitizer.

- The sanitizer gives off smoke or a burning smell while it is

operating.

Note: UV light can be harmful to the human eye and skin. This device

should be kept out of reach of children at all times.

1 After brushing, rinse the brush head and shake off excess water.

Warning: Do not place the travel cap on the brush head

during sanitization.

2 Place your finger in the door recess on top of the sanitizer and pull

open the door (Fig. 10).

3 Place the brush head on one of the 2 pegs in the sanitizer with the

bristles facing the light bulb (Fig. 11).

Note: Only clean Philips Sonicare snap-on brush heads in the

sanitizer.

Note: Do not clean Philips Sonicare for Kids brush heads in the

sanitizer.

4 Make sure the sanitizer is plugged into a live outlet of appropriate

voltage.

5 Close the door and press the green power on/off button once to

select the UV clean cycle.

Note: You can only turn on the sanitizer if the door is properly

closed.

Note: The sanitizer stops if you open the door during the sanitizing

cycle.

Note: The sanitizer cycle runs for 10 minutes and then

automatically shuts off.

17

English

-

The sanitizer is in operation when the light glows through the

window.

Cleaning

Warning: Do not clean the brush head, handle, travel charger

or the UV sanitizer in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water. Make sure you remove any residual toothpaste (Fig. 12).

Caution: Do not push on the rubber seal on the metal shaft with

sharp objects, as this may cause damage.

2 Wipe the entire surface of the handle with a damp cloth.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 13).

2 Remove the brush head from the handle and rinse the brush head

connection with warm water at least once a week. Rinse the travel

cap as often as needed.

Charger

1 Unplug the charger before you clean it.

2 Wipe the surface of the charger with a damp cloth. Make sure you

remove any toothpaste or other residue from the charger surfaces.

Sanitizer

Warning: Do not immerse the sanitizer in water or rinse it

under the faucet.

Warning: Do not clean the sanitizer when the UV light bulb is

hot.

For optimal effectiveness, it is recommended to clean your sanitizer

weekly.

1 Unplug the sanitizer.

2 Pull the drip tray straight out. Rinse the drip tray and wipe it clean

with a damp cloth (Fig. 14).

18

English

3 Clean all interior surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb (Fig. 15).

To remove the screen, grasp the edges next to the snaps, gently

squeeze and pull out the protective screen.

5 Remove the UV light bulb.

To remove the light bulb, grasp it and pull it out of the metal clasp.

6 Clean the protective screen and the UV light bulb with a damp

cloth.

7 Reinsert the UV light bulb.

To reinsert the light bulb, align the bottom of the light bulb with

the metal clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

To reinsert the screen, align the pegs on the screen with the slots

on the reflective surface near the UV light bulb. Push the screen

straight into the slots on the sanitizer.

Storage

If you are not going to use the product for a long time, unplug it, clean

it (see chapter 'Cleaning') and store it in a cool and dry place away

from direct sunlight. You can use the integrated cord wrap to store

excess cord of the UV sanitizer in an organized manner.

Replacement

Brush head

- Replace Philips Sonicare brush heads every 3 months to achieve

optimal results.

Note: The Sonicare App will tell you when it is time to replace your

brush head. (See in-app Help section)

- Use only Philips Sonicare replacement brush heads.

19

English

UV light bulb

- Replacement UV bulbs are available through your Philips Sonicare

Consumer Service Center in North America by calling

1-800-682-7664. Outside North America, contact your local Philips

Consumer Care Center.

Recycling

- This symbol means that this product shall not be disposed of with

normal household waste (2012/19/EU) (Fig. 19).

- This symbol means that this product contains a built-in

rechargeable battery which shall not be disposed of with normal

household waste (Fig. 20) (2006/66/EC). We strongly advise you

to take your product to an official collection point or a Philips

service center to have a professional remove the rechargeable

battery.

- Follow your country’s rules for the separate collection of electrical

and electronic products and rechargeable batteries. Correct

disposal helps prevent negative consequences for the

environment and human health.

Removing the rechargeable battery

Warning: PLEASE NOTE THAT THIS PROCESS IS NOT

REVERSIBLE.

- To remove the rechargeable battery, you need a flat-head

(standard) screwdriver. Observe basic safety precautions when you

follow the procedure outlined below. Be sure to protect your eyes,

hands, fingers, and the surface on which you work.

1 To deplete the rechargeable battery of any charge, remove the

handle from the charger, turn on the Philips Sonicare and let it run

until it stops. Repeat this step until you can no longer switch on

the Philips Sonicare.

2 Insert a screwdriver into the slot located at the bottom of the

handle and turn counterclockwise to release the bottom cap (Fig.

16).

3 Hold the handle upside down and push down on the shaft to

release the internal components of the handle (Fig. 17).

20

English

Pagina se încarcă ...

Sonicare HX9192/01 Manual de utilizare

Sonicare HX9192/01 Manual de utilizare

în alte limbi

Lucrări conexe

Alte documente