Yamaha RX-V567 Manual de utilizare

RX-V567
Yamaha
Marca
Yamaha
Model
RX-V567
Tip
Manual de utilizare

Acest manual este potrivit și pentru

Firmware Update Procedure for RX-V467/RX-V567
Page.1 of 5
May, 2010
Subject: RX-V467/RX-V567 Firmware Update Version E017
(Including HTR-4063/HTR-5063)
Yamaha is pleased to offer the following firmware update to ensure the best possible
performance and features for your Yamaha RX-V467/RX-V567 AV Receiver. This
firmware adds 3D video pass-through capability for the HDMI connections.
Requirements:
A personal computer capable of burning an audio CD
BD/DVD/CD player* with digital audio connection
(Optical or Coaxial, not HDMI)
*Note
CD PLAYER IS PREFERRED.
Some DVD players use digital filters, which affects the output signal of the
devices. This firmware update may not work with DVD players which use these
digital filters. CD players usually do not use these filters.
CHECK THE UNIT’S FIRMWARE VERSION PRIOR TO THIS UPDATE
The firmware version consists of a letter followed by three numbers [ex. “E017”].
If the three numbers in the firmware version are 017 or higher, you DO NOT need to
perform this update.
How to check your firmware version:
Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you
press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP",
release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for
about 3 seconds until front panel display shows the firmware version.
The following pages contain the firmware update instructions for Yamaha AV receivers
RX-V467/V567. The outline of the update is as follows:
1. Create an update disc (Audio CD)
2. Connect digital audio with CD, DVD or BD player
3. Enter firmware update mode
4. Play the update disc (Reprogramming)
5. Confirm update firmware version
< IMPORTANT NOTICE >
Do not attempt to update your Yamaha receiver using any other data file except those provided
directly from the Yamaha website.
Follow the instructions carefully and do not attempt any other procedures not specified in the
instructions provided by Yamaha.
Improperly updated products may cause improper operation, and any parts or service required
to restore proper operation will not be covered under the Yamaha Limited Warranty.
Firmware Update Procedure for RX-V467/RX-V567
Page.2 of 5
Instructions for Firmware Update:
STEP1 CREATE UPDATE DISC
Download the firmware from YAMAHA website.
Unzip and burn the WAV file onto CD-R/RW as an Audio-CD. This will be your
update disc.
If you need instructions on creating this firmware update CD, see your Personal
Computer ("PC") CD burning software instructions on how to burn WAV file as an
Audio CD.
Note:
Conventional CD burning software is
recommended. An audio CD burned by
Windows Media Player may not work.
STEP2 CONNECT DIGITAL AUDIO WITH BD/DVD/CD PLAYER
Unplug the AC power cable of the receiver from the wall outlet and turn off the
power of BD/DVD/CD player. Then, connect CD DVD or BD player* using
digital connection (Coaxial or Optical) into any input of your receiver.
*Some DVD players use digital
filters, which affects the output
signal of the devices. The firmware
update will not work with DVD
players which use these digital
filters. CD players usually do not
use these filters, so using a CD
player is preferred.
Picture shows an example of the
connection. Depending on your
BD/DVD/CD player's digital output,
connect the receiver with either
optical or coaxial.
<Connection with OPTICAL cable>
<Connection with COAXIAL cable>
Firmware Update Procedure for RX-V467/RX-V567
Page.3 of 5
STEP3 ENTER FIRMWARE UPDATE MODE
Plug the AC power cable of the AV receiver.
Press and hold the [STRAIGHT] button on the front panel and keep it pressed
while you press the [STANDBY/ON] button. Once the front panel displays
"Advance Setup", release the [STRAIGHT] button. Then, press and hold the
[INFO] button for about 3 seconds until front panel displays “CDDA Upgrader”.
Now your AV receiver is ready for firmware update.
STEP4 START FIRMWARE UPDATE
Turn on the BD/DVD/CD player.
Load the Firmware Update CD (Audio CD) and press [PLAY] button on the
BD/DVD/CD player.
“Found Header” will appear on the AV receiver for few seconds. Then, the
firmware update starts.
“Found Header” appears within 10 seconds from starting update disc playback.
In case display doesn’t change after 10 seconds, retry the update process again
from the beginning or check requirements for the update disc and connection.
See IN CASE OF ERROR for details.
When completed, “Update Success”, “Please...” and “Power off!!” are
displayed repeatedly. Turn off the power of AV receiver.
Stop the BD/DVD/CD player, remove update disc and power off.
While update is in progress,
DO NOT interrupt the AV receiver by pressing any buttons or
switching off the power.
STANDBY/ON
INFO
TONE CONTROL
STRAIGHT
Firmware Update Procedure for RX-V467/RX-V567
Page.4 of 5
STEP5 CHECK UPDATED VERSION
Press and hold the [STRAIGHT] button on the front panel and keep it pressed
while you press the [STANDBY/ON] button. Once the front panel displays
"ADVANCED SETUP", release the [STRAIGHT] button. Then, press and hold
the [TONE CONTROL] button for about 3 seconds until front panel displays
“M:E017 7589”.
E017: version of firmware
7589: checksum
If your firmware version number and checksum don't match, retry from step 3.
Or try the IN CASE OF ERROR method on the last page.
Turn off the power of AV receiver.
Congratulations!
You have completed the firmware update. Your AV receiver is ready for normal use.
Firmware Update Procedure for RX-V467/RX-V567
Page.5 of 5
IN CASE OF ERROR
Case1 Display on the receiver “CDDA Upgrader” doesn’t change after playing the
BD/DVD/CD player.
Check digital cable wiring. Only optical or coaxial connection can be used for
this update. HDMI connection will not work.
Check digital out setting. When using DVD/BD players, make sure the digital
out is set to “PCM”. Once update is completed, reset DVD/BD player to its
original settings.
Check update disc. Make sure that your CD-R/RW is finalized and created
as an “AUDIO CD”. (playable on any BD/DVD/CD player)
If all above are cleared, your BD/DVD/CD player may not be suited for this
update. Try another BD/DVD/CD player or contact your local authorized
service center to update the receiver for you.
Case2 Other unintended error occurred.
"ERROR" was displayed during the update
Receiver doesn't power up after the update.
Solution: Try the following recovery method
Step PL1. Unplug the AC power cable of the AV receiver from wall outlet.
Step PL2. On the front panel of the AV receiver, press and hold the [INFO] button
and keep it pressed, while you plug the AC power cable of the Yamaha
receiver to the wall outlet. Once the front panel displays "CDDA
Upgrader" release the [INFO] button.
Step PL3. Go to Step 4 “START FIRMWARE UPDATE”.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Yamaha RX-V567 Manual de utilizare

RX-V567
Yamaha
Marca
Yamaha
Model
RX-V567
Tip
Manual de utilizare
Acest manual este potrivit și pentru
Descărcați PDF
raport

în alte limbi

Lucrări conexe