Philips HQ9190/21 Manual de utilizare

ENGLISH 4
POLSKI 23
РУССКИЙ 43
УКРАЇНСЬКА 64
EESTI 84
LATVIEŠU 101
LIETUVIŠKAI 120
139
ROMÂNĂ 158
ČEŠTINA 177
MAGYAR 196
SLOVENSKY 215
HRVATSKI 234
SLOVENŠČINA 253
БЪЛГАРСКИ 272
SRPSKI 293
HQ9190, HQ9171, HQ9170 

Important

Read these instructions for use carefully before

using the appliance and save them for future

reference.

◗ Only use the powerplug supplied.

◗ The powerplug transforms 100-240 volts to a

safe low voltage of less than 24 volts.

◗ The powerplug contains a transformer.

Do not cut off the powerplug to replace it

with another plug, as this will cause a

hazardous situation.

◗ Do not use a damaged powerplug.

◗ If the powerplug is damaged, always have it

replaced by one of the original type in order

to avoid a hazard.

C

◗ Make sure the powerplug does not get wet.

◗ Charge and store the appliance at a

temperature between 5cC and 35cC.

C

◗ Never immerse the charging stand in water

nor rinse it under the tap.

◗ Do not recharge the shaver in a closed pouch.

◗ Always unplug the shaver before cleaning it

under the tap.

C

◗ The appliance complies with the

internationally approved IEC safety regulations

and can be safely cleaned under the tap.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

◗ Noise level: Lc = 64 dB [A]

ENGLISH4

The display

C

◗ This appliance offers you the unique

possibility to choose the display layout you

prefer: a number layout or a battery symbol

layout.

1 Press the on/off button approx. 3 seconds

to enter the menu.

The menu has three different modes: the travel

lock mode and two display layout modes.

C

◗ You will enter the menu in the travel lock

mode, indicated by a rotating key symbol.

You can scroll through the three modes (travel

lock, battery symbol layout and number layout) by

pressing the on/off button briefly in quick

succession.

2 To select one of the two display layouts,

stop pressing the on/off button when the

layout you prefer appears on the display.

Wait a few seconds without pressing the on/off

button until you hear a beep.This beep indicates

that the display has been set to the selected

layout.

B

Note: the first mode you enter after pressing the

on/off button for 3 seconds is the travel lock mode

(indicated by a rotating key symbol). If you do not

press the on/off button again within a few

seconds, the travel lock is activated and the

display will not switch to the first display layout

ENGLISH 5

mode.To deactivate the travel lock, press the

on/off button for 3 seconds again (see chapter

'Storage').

You can change the display layout at any time.

B

Note: when you start using the appliance for the

first time or after a long period of disuse, it could

take several minutes before anything appears on

the display.

The display provides the following information:

Charging

C

◗ Number layout:

When the shaver is being charged, the display

shows the minutes indication and the plug symbol

with a blinking power symbol.

C

◗ Battery symbol layout:

When the shaver is being charged, the display

shows the battery symbol and the plug symbol

with a blinking power symbol.

Battery fully charged

C

◗ As soon as the battery has been fully charged,

the word 'FULL' runs across the display.

◗ After a few hours the word 'FULL' stops

appearing.The display shows the minutes

indication and the plug symbol.

ENGLISH6

Battery running low

C

◗ Number layout:

When the battery is running low, the display

shows a blinking minutes indication and blinking

plug symbol when you switch the shaver off.

HQ9190 only: you will also hear a few short

beeps.

C

◗ Battery symbol layout:

When the battery is running low, the display

shows a blinking battery symbol and blinking plug

symbol when you switch the shaver off. HQ9190

only: you will also hear a few short beeps.

Battery empty

C

◗ To indicate that the battery voltage is too low

to operate the appliance, "LO" appears on the

display.

◗ Recharge the battery. See chapter 'Charging'.

Cleaning shaver

C

◗ When the shaver is due to be cleaned, the tap

symbol with blinking water drops appears on

the display.

ENGLISH 7

Replacing shaving heads

C

◗ When the shaving heads need to be replaced

(every two years), the shaving unit symbol

starts blinking when you switch the shaver off.

HQ9190 only: at the same time you will hear

a beep.

- If you do not replace the shaving heads right

away, the shaving unit symbol remains visible

during the next 7 shaves.

- You can reset the appliance by pressing the

on/off button for 3 seconds while the shaving

unit symbol is blinking.The shaving unit symbol

then disappears. HQ9190 only: you will hear a

short confirming beep.

- If you have not reset the system after these

7 shaves, the system will automatically reset

itself.

Demonstration program

The appliance has a unique demonstration

program.

◗ Press the on/off button for 6 seconds.

After 3 seconds the lock symbol appears; keep

the on/off button pressed.

The demonstration will start automatically. During

the demonstration the appliance will be

automatically switched on 2 times.You can

interrupt the demonstration by pressing the

on/off button.

ENGLISH8

Charging

Make sure the appliance is switched off before

you start charging it.

Charging normally takes approx. 1 hour.

You can also shave without charging by

connecting the shaver to the mains.

A fully charged shaver has a cordless shaving time

of up to 30 days.

Charging the appliance

C

1 Put the appliance plug in the shaver.

2 Put the powerplug in the wall socket.

3 Remove the powerplug from the wall

socket and pull the appliance plug out of

the shaver when the battery has been fully

charged.

Charging stand

◗ You can also charge the appliance by placing it

in the charging stand.

C

◗ Place the shaver properly in the plugged-in

charging stand.

ENGLISH 9

C

◗ Lift the shaver from the stand without tilting

it.

Removing and inserting the clock

C

1 Turn the clock anticlockwise (1) ('click')

and pull it out (2).

C

2 Insert the clock (1) and turn it clockwise

(2) ('click').

Setting the time

C

◗ Set the time by pressing the small button at

the back of the clock.

The time can only be set forward.

ENGLISH10

Replacing the battery

C

1 Remove the cap.Then remove the battery

by means of a miniature screwdriver.

C

2 Insert a new battery and put the cap back

into place.

Using the appliance

Personal Comfort Control

C

◗ The Personal Comfort Control system allows

you to adapt the shaver to your skin type.

- You can set the shaver to 'Normal' for a fast

and comfortable close shave.

- You can set the shaver to 'Sensitive' for a

comfortable close shave with optimal skin

comfort.

C

◗ The 'S' position is best suited for sensitive

skin.

ENGLISH 11

C

◗ The 'N' position is best suited for normal

skin.

◗ The in-between positions are suitable for skin

types between normal and sensitive.

C

◗ HQ9190 only: the display shows the position

selected.

Shaving

1 Switch the shaver on by pressing the on/off

button once.

When you switch the shaver on or off, all lights

and symbols go on and then the remaining

battery capacity is shown for a few seconds.

C

2 Move the shaving heads quickly over your

skin, making both straight and circular

movements.

- Shaving on a dry face gives the best results.

- Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

3 Switch the shaver off by pressing the on/off

button once.

C

4 Put the protection cap on the shaver every

time you have used it, to prevent damage.

ENGLISH12

Trimming

For grooming sideburns and moustache.

C

1 Open the trimmer by pushing the slide

downwards.

The trimmer can be activated while the motor is

running.

C

2 Close the trimmer with your index finger.

Cleaning and maintenance

Clean the shaver when the tap symbol with

blinking water drops appears on the display.

Regular cleaning guarantees better shaving

performance.

The normal way to clean the appliance is to rinse

the shaving unit and the hair chamber with hot

water every time you have used the shaver.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

ENGLISH 13

Every day: shaving unit and hair chamber

1 Switch the shaver off, remove the

powerplug from the wall socket and pull

the appliance plug out of the shaver.

C

2 Press the release button to open the

shaving unit.

C

3 Clean the shaving unit and the hair

chamber by rinsing them under a hot tap

for some time.

Make sure the inside of the shaving unit and the

hair chamber have been cleaned properly.

C

4 Rinse the outside of the appliance.

5 Close the shaving unit and shake off excess

water.

Never dry the shaving unit with a towel or tissue

as this may damage the shaving heads.

C

6 Open the shaving unit again and leave it

open to let the appliance dry completely.

You can also clean the hair chamber without

water by using the brush supplied.

ENGLISH14

Every six months: shaving heads

C

1 Open the shaving unit, turn the lock

anticlockwise (1) and remove the retaining

frame (2).

2 Clean the cutters and guards with the

brush supplied.

Do not clean more than one cutter and guard at

a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it may

take several weeks before optimal shaving

performance is restored.

3 Put the shaving heads back into the shaving

unit. Put the retaining frame back into the

shaving unit and turn it clockwise.

4 Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it.

1 Switch the shaver off, remove the

powerplug from the wall socket and pull

the appliance plug out of the shaver.

C

2 Clean the trimmer with the brush

supplied.

ENGLISH 15

C

3 Lubricate the trimmer teeth with a drop

of sewing machine oil every six months.

Charging stand

Never immerse the charging stand in water nor

rinse it under the tap.

You can clean the charging stand with a moist

cloth.

Storage

C

◗ Put the protection cap on the shaver to

prevent damage.

C

◗ Store the appliance in the luxury

cassette/pouch or place the appliance in the

charging stand.

Travel lock

If you are going to travel, it is possible to lock the

shaver.The travel lock prevents the shaver from

being switched on by accident.

ENGLISH16

Activating the travel lock

◗ Press the on/off button for 3 seconds to enter

the travel lock mode (indicated by a rotating

key symbol).

◗ Wait a few seconds without pressing the

on/off button to activate the travel lock.

C

◗ The motor switches off and the key symbol is

visible on the display to indicate that the

travel lock has been activated.

B

Note: if you press the on/off button again within a

few seconds after entering the travel lock mode,

the travel lock will not be activated. Instead, you

will have entered one of the two display layout

modes. If you want to return to the travel lock

mode, press the on/off button two more times

until you are back in the travel lock mode

(indicated by rotating the key symbol).Then wait a

few seconds without pressing the on/off button to

activate the travel lock.

◗ You can always return to the menu by

pressing the on/off button for 3 seconds.

Deactivating the travel lock

◗ Press the on/off button for 3 seconds.

The motor starts running to indicate that the

shaver has been unlocked.The shaver is now

ready for use again.

Replacement

Replace the shaving heads when the shaving unit

symbol appears on the display.

ENGLISH 17

Replace damaged or worn shaving heads with

HQ9 Philips shaving heads only.

1 Switch the shaver off, remove the

powerplug from the wall socket and pull

the appliance plug out of the shaver.

C

2 Press the release button to open the

shaving unit.

C

3 Turn the lock anticlockwise (1) and

remove the retaining frame (2).

C

4 Remove the shaving heads and place new

ones in the shaving unit.

Make sure that the projections of the shaving

heads fit exactly into the recesses.

C

5 Put the retaining frame back into the

shaving unit (1) and turn the lock

clockwise (2).

6 Close the shaving unit.

◗ The shaving unit symbol will go out if you

keep the on/off button pressed for 3 seconds.

Accessories

The following accessories are available:

- HQ8000 powerplug.

ENGLISH18

- HQ9 Philips shaving heads.

- HQ110 Philips shaving head cleaner

(shaving head cleaning spray).

- HQ8010 car cord.

Environment

C

◗ Do not throw the appliance away with the

normal household waste at the end of its life,

but hand it in at an official collection point for

recycling. By doing this you will help to

preserve the environment.

◗ The built-in rechargeable battery contains

substances that may pollute the environment.

Always remove the battery before discarding

the appliance or handing it in at an official

collection point. Dispose of the battery at an

official collection point for batteries. If you

have trouble removing the battery, you can

also take the appliance to a Philips service

centre, which will remove the battery for you

and will dispose of it in an environmentally

safe way.

Disposal of the shaver battery

Only remove the battery if it is completely empty.

1 Remove the powerplug from the wall

socket and pull the appliance plug out of

the shaver.

C

2 Let the shaver run until it stops, undo the

screws and open the shaver.

ENGLISH 19

3 Remove the battery.

Do not connect the shaver to the mains again

after the battery has been removed.

Guarantee & service

If you need information or if you have a problem,

please visit the Philips website at

www.philips.com or contact the Philips Customer

Care Centre in your country (you will find its

phone number in the worldwide guarantee

leaflet). If there is no Customer Care Centre in

your country, turn to your local Philips dealer or

contact the Service Department of Philips

Domestic Appliances and Personal Care BV.

Troubleshooting

1 Reduced shaving performance

B

Cause 1: the shaving heads are dirty.

The shaver has not been rinsed long enough or

the water used was not hot enough.

◗ Clean the shaver thoroughly before you

continue shaving. See chapter 'Cleaning and

maintenance'.

B

Cause 2: long hairs are obstructing the shaving

heads.

ENGLISH20

◗ Clean the cutters and guards with the brush

supplied. See chapter 'Cleaning and

maintenance', section 'Every six months:

shaving heads'.

B

Cause 3: the shaving heads are damaged or worn.

◗ Replace the shaving heads. See chapter

'Replacement'.

2 The shaver does not work when the on/off

button is pressed.

B

Cause 1: the battery is empty.

◗ Recharge the battery. See chapter 'Charging'.

B

Cause 2: the appliance is not connected to the

mains.

◗ Put the powerplug in the wall socket.

C

3 The shaving unit has come off the shaver.

B

Cause: the shaving unit has not been placed

correctly.

◗ If the shaving unit becomes detached from the

shaver, you can easily reattach it ('click').

4 The display shows the word CHECK and a

blinking shaving unit symbol and tap unit

symbol.

ENGLISH 21

B

Cause 1: long hairs and dirt are obstructing the

shaving heads.

◗ Clean the shaver thoroughly before you

continue shaving. See chapter 'Cleaning and

maintenance'.

B

Cause 2: the shaving heads are damaged or worn.

◗ Replace the shaving heads. See chapter

'Replacement'.

ENGLISH22

Pagina se încarcă ...

Philips HQ9190/21 Manual de utilizare

Philips HQ9190/21 Manual de utilizare

în alte limbi

Lucrări conexe