Yamaha RX-V480 Manual de utilizare

Categorie
Casetofoane
Tip
Manual de utilizare
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Natural Sound Stereo Receiver
Récepteur stéréo “Son Naturel”
Natural Sound Stereoreceiver
Natural Sound Stereoreceiver
Sintonizzatore stereo a suono naturale
Receptor estéreo de Sonido Natural
Natural Sound Stereo Ontvanger
RX-V480
2
Indoor FM Antenna
Antenne FM intérieure
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena FM interior
FM Binnenantenne
AM Loop Antenna
Cadre-antenna AM
MW-Rahmenantenne
AM ramantenn
Antenna AM ad anello
Antena de cuadro de AM
AM Lusantenne
Remote Control Transmitter
Emetteur de télécommande
Fernbedienungsgeber
Fjärrkontrollsändare
Telecomando
Transmisor del control remoto
Afstandbediening
Batteries (size AA, R6, UM-3)
Piles (taille AA, R6, UM-3)
Batterien (Größe AA, R6, UM-3)
Batterier (storlek AA, R6, UM-3)
Batterie (dimensioni AA, R6, UM-3)
Pilas (tamaño AA, R6, UM-3)
Batterijen (maat AA, R6, UM-3)
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are included.
ACCESSOIRES FOURNIS
Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTE ZUBEHÖRTEILE
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR
Kontrollera efter det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
ACCESORIOS INCLUIDOS
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj.
Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.
Este producto está de acuerdo con los requisitos sobre interferencias de radio frequencia fijados por el Consejo Directivo
87/308 CEE.
Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
POWER SLEEP PLAY PHONO
PAUSE/STOP
CD
TUNER
A/B/C/D/E
LD/TV
DECK A/B
TAPE MON
VCR MON
CENTER
MODE
PRO LOGIC
ENHANCED CNCT VIDEO
+
MONO MOVIE
VOLUME
HALL
+
PRESET
SKIP
PLAY
+
DISC SKIP
STOP
REC/PAUSE
DELAY
TIME
EFFECT
ON/OFF
ROCK
SUR.
DIR A DIR B
FEATURES
CONTENTS
3
English
5 Speaker Configuration
Front: (U.S.A. model)
65W + 65W (8) RMS Output Power, 0.04% THD, 20–20,000 Hz
(Canada model)
55W + 55W (8) RMS Output Power, 0.04% THD, 20–20,000 Hz
(Australia, Europe, U.K. and General models)
60W + 60W (8) RMS Output Power, 0.04% THD, 20–20,000 Hz
Center: (U.S.A. model)
65W (8) RMS Output Power, 0.1% THD, 1 kHz
(Canada model)
55W (8) RMS Output Power, 0.1% THD, 1 kHz
(Australia, Europe, U.K. and General models)
60W (8) RMS Output Power, 0.1% THD, 1 kHz
Rear: 15W + 15W (8) RMS Output Power, 0.7% THD, 1 kHz
Digital Sound Field Processor
4 Programs for Digital Sound Field Processing
2 Programs Dolby Surround (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED)
Automatic Input Balance Control for Dolby Surround
Test Tone Generator for Easier Speaker Output Balance Adjustment
3 Center Channel Modes (NORMAL/WIDE/PHANTOM)
40-Station Random Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability
IF Count Direct PLL Synthesizer Tuning System
Video Signal Input/Output Capability
SLEEP Timer
Remote Control Capability
Supplied Accessories ......................................2
Caution ............................................................4
Profile of This Unit ...........................................5
Speaker Setting-up for This Unit .....................6
Connections ....................................................7
Adjustment Before Operation ........................10
Operations .....................................................13
Tuning Operations .........................................16
Preset Tuning ................................................17
Using Digital Sound Field Processor (DSP)
.........20
Setting the SLEEP Timer ..............................24
Remote Control Transmitter ..........................25
Notes about the Remote Control Transmitter
.......................................................................26
Troubleshooting .............................................27
Specifications ................................................28
Thank you for selecting this YAMAHA stereo receiver.
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
6. Always set the VOLUME control to “–
” before starting the audio
source play. Increase the volume gradually to an appropriate level
after playback has been started.
7. Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9. When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10.To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMERS
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS SET OUT IN THE RADIO INTERFERENCE
REGULATIONS OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note: The plug severed from the mains lead must be destroyed,
as a plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the main lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The wire
which is coloured BROWN must be connected to the terminal which
is marked with the letter L or coloured RED. Make sure that neither
core is connected to the earth terminal of the three pin plug.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in different
areas, set the FREQUENCY STEP switch (located at the rear)
according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of this unit
from the AC outlet.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
5
English
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Rather than tell you about the wonders of digital sound field processing, however, let’s get right down to the business of setting up
the system and trying out its many capabilities. Please read this operation manual carefully and store it in a safe place for later
reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
What’s more, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of Dolby Surround
movie theater sound in your own home. Dolby Pro Logic gets
its name from its professional-grade steering logic circuitry,
which provides greater effective channel separation for a much
higher degree of realism than the “passive” Dolby Surround
circuits found in today’s typical home audio/video equipment.
Dolby Pro Logic Surround provides a true center channel, so
that there are four independent channels, unlike passive Dolby
Surround which has in effect only three channels: left, right,
and rear. This center channel allows listeners seated in even
less-than-ideal positions to hear the dialog originating from
action on the screen while getting a stereo effect as well.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system increases sound
stability at each channel and minimizes crosstalk between
channels compared to conventional analog Dolby signal
processing.
In addition, this unit features a built-in automatic input balance
control. This circuit always presents you the best surround
conditions without performing manual adjustments.
Dolby Pro Logic Surround + DSP
You can also enjoy a combination of Dolby Pro Logic Surround
and DSP in the sound field program “ PRO LOGIC
ENHANCED”.
It recreates the surround effect of a movie theater, effectively
duplicating its multiple surround loudspeaker system,
completely surrounding the listener with the sounds of the
action taking place on the screen.
6
SPEAKER SETTING UP FOR THIS UNIT
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The speakers to be used with this unit
will be mainly front speakers, rear speakers, and a center speaker. (You can omit the center speaker. Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the output of the main source sound and the effect sound. They will probably be the speakers of
your present stereo speaker system. The rear speakers are used for the output of the effect sound. And the center speaker is
used for the output of the center sound (dialog etc.) encoded with the Dolby Surround. The rear and center speakers do not need
to be equal in power to the front speakers. However, all the speakers should have high enough power handling to accept the
maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and is the one that is
recommended. In this configuration, the center speaker is
necessary as well as the rear speakers. If the digital sound
field program is in DOLBY PRO LOGIC or DOLBY PRO
LOGIC ENHANCED mode conversations will be output from
the center speaker and the ambience will be excellent.
Set the center mode to the “NORMAL” or “WIDE” position.
(For details, refer to page 11.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
digital sound field program is in the DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED mode, the center sound is
output from the left and the right front speakers. However, the
sound effect of other programs can be the same as that of the
5-speaker configuration.
Be sure to set the center mode to the “PHANTOM” position.
(For details, refer to page 11.)
SPEAKER PLACEMENT
The recommanded speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the front speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker. If, however, it is not effective, keep the
speaker away from TV sets.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
7
English
CONNECTIONS
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
:Refer to “ABOUT THE ACCESSORY TERMINALS” on page 8.
R L
A
B
75
UNBAL
PHONO CD LD
/
TV IN OUT
LD
/
TV
IN
OUT
MONITOR
OUT
VCR
REAR
CENTER
REAR
A
B
SWITCHED
FM
ANT
GND
AM
ANT
SPEAKERS
TAPE
PB
REC
OUT
TAPE VCR
R
L
AUDIO SIGNAL
SPEAKERS
AC OUTLETS
LD player Video cassette recorder
Turntable Compact disc
player
Tape deck Monitor TV
To AC outlet
AUDIO OUT
VIDEO OUT
AUDIO OUT
AUDIO IN
VIDEO OUT
VIDEO IN
GND
OUTPUT
OUTPUT
LINE OUT
LINE IN
VIDEO IN
GND
120V 50Hz
100W MAX TOTAL
VIDEO
SIGNAL
(U.S.A. model)
LD player, TV tuner,
etc.
8
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
Use speakers with the specified impedance shown on the
rear of this unit.
Note for front speaker connection:
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
How to Connect:
Red: positive (+)
Black: negative (–)
Press up the tab.
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Press down the tab and
secure the wire.
CONNECTING SPEAKERS
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
(U.S.A., Canada, Europe and General models)
............................................................2 SWITCHED OUTLETS
(Australia and U.K. models)
.............................................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote-control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
minimize hum, but in some cases better results may be
obtained with the ground wire disconnected.
R L
A
B
IN OUT
REAR
CENTER
REAR
A
B
SPEAKERS
REC
OUT
TAPE VCR
R
L
SPEAKERS
Front speakers A
Right Left
Right Left
Front speakers B
Rear speakers
Right
Left
Center speaker
9
English
ANTENNA CONNECTIONS
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
When connecting the indoor
FM antenna, make sure that
the grooved part of the
connector hole is facing
downward.
If you need an outdoor
FM antenna to improve
FM reception quality, either 300-ohm feeder or coaxial cable
may be used. In locations troubled by electrical
interference, coaxial cable is preferable.
75
UNBAL
PHONO CD LD/TV
LD
/
TV
IN
OUT
MONITOR
OUT
VCR
GND
FM
ANT
GND
AM
ANT
VIDEO
SIGNAL
TAPE
PB
AUDIO SIGNAL
300-ohm feeder
75-ohm
coaxial cable
75-ohm/300-ohm
antenna adapter
Ground
Outdoor FM antenna
Indoor FM
antenna
(included)
Outdoor AM antenna
AM loop
antenna
(included)
Orient so that the best
reception is obtained.
12 3
10
ADJUSTMENT BEFORE OPERATION
Speaker balance adjustment
This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test
tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker.
This is important for the best performance of the digital sound field processor.
Set to the “
” position.
Select the front speakers to be used.
* If you use two front speaker systems, press both the A
and B switches.
Set to the “0” position.
Turn the DSP on, so that a DSP program name
appears on the display.
Select the PRO LOGIC or PRO LOGIC
ENHANCED mode, so that the corresponding name is
illuminated on the display.
1
5
2
3
4
5
1
4
23
SPEAKERS
A
B
ON
OFF
ON
OFF
6
—dB
VOLUME
0
POWER
EFFECT
PRO LOGIC
ENHANCED
SUR.
CENTER
MODE
PRO LOGIC
ENHANCED CNCT VIDEO
+
MONO MOVIE
VOLUME
HALL
+
DELAY
TIME
EFFECT
ON/OFF
ROCK
SUR.
6
11
English
Select the center channel output mode according to
your speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
On the feature of each mode, refer to the “Note” shown
below.
Turn up the volume.
You will hear a test tone (like pink noise) from the left
front speaker, then the center speaker, then the right
front speaker, and then the rear speakers, for about two
seconds each. The display changes as shown below.
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
Note
In step 7, when you select the center channel output mode,
note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the front speakers. In this
mode, the bass tone will be output from the front
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the front speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right front speakers.
78
9
Flashes continuously.
0
—dB
VOLUME
8
9
CENTER
MODE
TEST
TEST
NORMAL
WIDE
PHANTOM
TEST
Front (L) Center
Rear
(L and R)
Front (R)
CONTINUED
DECK A/B VCR MON
CENTER
MODE
PRO LOGIC
ENHANCED CNCT VIDEO
+
MONO MOVIE
VOLUME
HALL
+
STOP
REC/PAUSE
DELAY
TIME
EFFECT
ON/OFF
ROCK
SUR.
7
12
Adjust the BALANCE control so that the effect sound
output level of the left front speaker and the right front
speaker are the same.
Make the sound output level of the center speaker the
same as that of the front speakers with the CENTER
level control.
Make the sound output level of the rear speakers the
same as that of the front speakers with the REAR
level control.
Cancel the test tone.
Stops flashing and disappears.
Notes
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using the
VOLUME control (or the VOLUME keys on the remote
control transmitter).
If you use external power amplifiers, their volume controls
may also be adjusted to achieve proper balance.
In step 11, if the center mode is in the “PHANTOM” position,
the sound output level of the center speaker can not be
adjusted. This is because in this mode, the center sound is
automatically output from the left and right front speakers.
10
11
12
13
BALANCE
0
L 5
5 R
11
10
12
13
CENTER
0I0
TEST
REAR
0I0
TEST
TEST
TEST
13
English
OPERATIONS
Set to the “
” position.
Select the desired input source by using the input
selector switches.
(For video sources, turn the TV/monitor ON.)
* The name of the selected input source will appear in
the display.
Select the front speakers to be used.
* If you use two front speaker systems, press both the A
and B switches.
If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to the page 15) and use the digital
sound field processor. (Refer to the page 20.)
Play the source. (For detailed information on the
tuning operation, refer to the page 16.)
Adjust to the desired output level.
TO PLAY A SOURCE
1
2
3
4
5
6
7
Note
In step 3, if two or more program sources are selected at the
same time (by using the input selector switches), be sure to
remember the priority order of the input sources.
Priority order of sources: 1) TAPE, 2) VCR, 3) LD/TV,
TUNER, CD or PHONO.
If you select LD/TV, TUNER, CD or PHONO, be sure that
neither TAPE nor VCR have been selected.
If you select TAPE and VCR and another input selector
switch at the same time, the playback result will be the video
image from the VCR and the sound from the audio tape.
If you select both LD/TV and TAPE at the same time, the
playback result will be the video image from the LD player
and the sound from the audio tape.
Once you play the LD player, its video image will not be
interrupted even if other input selector switches except VCR
are selected.
For TAPE and VCR, whenever the switch is pressed, the
corresponding input source is selected or canceled
alternately.
— dB
VOLUME
0
POWER
SPEAKERS
A
B
ON
OFF
ON
OFF
0
— dB
VOLUME
3
1, 6
2
47
TAPE
MONITOR
COPY
INPUT
LD/TV TUNER
CD PHONO
VCR
Notes
To dub from tape to tape, only the following method of
dubbing can be performed.
DSP, VOLUME, BASS, TREBLE and BALANCE control
settings have no effect on the material being recorded.
14
Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown at
right.
* When you select LD/TV, TUNER, CD or PHONO, make
sure that neither TAPE nor VCR is also selected.
Play the source and then turn the VOLUME control
up to confirm the input source. (For detailed information
on the tuning operations, refer to the page 16.)
Set the tape deck or VCR to the recording mode.
To monitor the audio and/or video signals being
recorded, press the input selector switch for the audio
or video tape recorder being used to make the
recording.
TO RECORD A SOURCE TO TAPE
1
2
3
4
SOURCE
VCR (or tape deck)
connected to the VCR
terminals.
RECORDER
Tape deck connected to
the TAPE terminals.
2
1, 4
TAPE
MONITOR
COPY
INPUT
LD/TV TUNER
CD PHONO
VCR
TAPE
MONITOR
COPY
INPUT
LD/TV TUNER
CD PHONO
VCR
15
English
Because one or two speaker systems (as front speakers) can
be connected to this unit, the SPEAKERS switches allow you
to select speaker system A or B, or both at once.
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
Note
This control is effective only for the sound from the front
speakers.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Note
These controls are effective only for the sound from the front
speakers.
When you listen with headphones
Connect the headphones to the PHONES jack. You can listen
to the main sound through headphones. When listening with
headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
Selecting the SPEAKER system
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control
PHONES
SPEAKERS
A
B
ON
OFF
ON
OFF
BALANCE
0
L 5
5 R
BASS
5 +
5
0
TREBLE
5 +
5
0
1 Select the reception band (FM or AM) while watching
the display.
2
3 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
16
FM/AM
AM
FM
1 Select the reception band (FM or AM) while watching
the display.
2
3
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stopped is not the
desired one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
Display information
Displays the band and frequency of the received station.
Illuminates when an FM stereo broadcast is received in
stereo.
Indicates the signal level of the received station.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
AUTOMATIC TUNING MANUAL TUNING
FM/AM
TUNING
MODE
AUTO
/
MAN’L
MONO
TUNING
MODE
AUTO
/
MAN’L
MONO
TUNING
DOWN
UP
TUNING
DOWN
UP
STEREO
0
MHz
40 60
20
l00
FM
➀➁
AUTO TUNING
“AUTO TUNING”
goes off.
or
AM
FM
or
1
23
17
English
11 Select the page where the preset station is stored.
22
Select the preset station number.
1 Tune to a desired station.
(Refer to the previous page for tuning procedures.)
2
3 Select a desired page (A – E) of preset stations while
watching the display.
4
Select a preset station number (1–8) while watching the
display before “MEMORY” goes off from the display.
5
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations on other pages in the
same way by selecting other pages in step 3.
Notes
A new setting can be programmed in place of the former
one.
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If so,
it can be re-programmed by simply following the PRESET
TUNING steps.
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
To store stations To recall a preset station
MEMORY
MAN’L/AUTO FM
MEMORY
MAN’L/AUTO FM
PRESET
MEMORY
FM
Flashes on and off
for about 5 seconds.
A/B/C/D/E
PRESET
MEMORY
FM
A/B/C/D/E
PRESET
MEMORY
FM
PRESET
STATIONS
DOWN
UP
PRESET
STATIONS
DOWN
UP
AUTO TUNING
STEREO
0
MHz
40 60
20
l00
FM
Shows the displayd station
has been programmed to A1.
PRESET TUNING
3, 11
2, 5
4, 22
18
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 17.
To store stations
1
2
Flashes. Flashes.
After 5 seconds, the automatic preset tuning begins from A1.
Received stations are programmed to A1, A2 ... A8
sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the received first station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS button soon after the display begins
flashing on/off in step 2. After a few seconds, the automatic
preset tuning begins. The received first station is stored to C5,
and next stations to C6, C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 17.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 17.
Notes
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 17.
If the number of received stations is not enough to be
stored up to E8, the search is finished automatically after
searching through all frequencies.
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is week in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 17.
Press and
hold for about
3 seconds.
FM/AM
FM
MEMORY
MAN’L/AUTO FM
PRESET
MEMORY
AUTO TUNING
1
2
and
19
English
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations each other by easy operations.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 17).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Shows the exchange of stations is completed.
Flashes
Flashes
EDIT
EDIT
2, 4
20
USING DIGITAL SOUND FIELD PROCESSOR (DSP)
This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand and shape the audio
sound field from both the audio and video sources, for a theater-like experience in the listening/viewing room.
This digital sound field processor has 6 programs; 4 programs for digital sound field processing and 2 programs for the Dolby Pro
Logic Surround sound system (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED). You can create an excellent audio
sound field by selecting the suitable program and adding desired adjustments. In addition, when the digital sound field program is
in the DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED mode, the built-in automatic input balance control functions. This
presents you the best surround condition without manual adjustment.
AUTO TUNING
PRESET
STEREO
0
kHZ
MHz
40 60
20
l00
MEMORY
SLEEP
TAPE VCR MONITOR
AM
FM
NORMAL
WIDE
PHANTOM
TEST
DELAY
ms
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
ROCK
CONCERT
CONCERT
HALL
PROGRAM
TEST
EFFECT
DIGITAL SOUND FIELD PROCESSOR
REAR
0I0
CENTER
0I0
POWER SLEEP PLAY PHONO
PAUSE/STOP
CD
TUNER
A/B/C/D/E
LD/TV
DECK A/B
TAPE MON
VCR MON
CENTER
MODE
PRO LOGIC
ENHANCED CNCT VIDEO
+
MONO MOVIE
VOLUME
HALL
+
PRESET
SKIP
PLAY
+
DISC SKIP
STOP
REC/PAUSE
DELAY
TIME
EFFECT
ON/OFF
ROCK
SUR.
DIR A DIR B
Display
Front Panel
Remote Control Transmitter
Displays your selection on the
DSP or other informations.
Switches on/off the digital
sound field processor (DSP)
Selects a digital sound field program.
Used for speaker balance adjustment (For
details, refer to the page 10, 11 and 12.)
Adjusts sound output
level at each speaker.
(For details, refer to the
page 23.)
Selects the center
channel output mode.
(For details, refer to the
page 10, 11 and 12.)
Adjusts the delay time.
(For details, refer to the
page 23.)
Selects a digital sound
field program.
Switches on/off the
digital sound field
processor (DSP).
••
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Yamaha RX-V480 Manual de utilizare

Categorie
Casetofoane
Tip
Manual de utilizare