Yamaha CS-500 Manualul utilizatorului

Marca: Yamaha

Model: CS-500

Tip: Manualul utilizatorului

VIDEO CONFERENCE SYSTEM

CS-500

EN User Guide

CS-500 User Guide

Introduction ..........................................................................................................................................4

Features/functions...............................................................................................................................................................4

Available manuals ...............................................................................................................................................................5

About this manual ...............................................................................................................................................................5

Included items .....................................................................................................................................................................6

Separately sold items ..........................................................................................................................................................6

Available utility software ......................................................................................................................................................7

Updating the device firmware..............................................................................................................................................7

Controls and connectors.....................................................................................................................8

Front panel ..........................................................................................................................................................................8

Rear panel...........................................................................................................................................................................9

Remote control ..................................................................................................................................................................10

Procedures preparing for use ...........................................................................................................12

Procedure from connection to installation..........................................................................................................................12

Procedure for holding a meeting........................................................................................................................................12

Specifying device settings .................................................................................................................................................12

Setup and connections......................................................................................................................13

Installing the device...........................................................................................................................................................13

When installing on a TV ...............................................................................................................................................13

When mounting to a TV ...............................................................................................................................................14

When mounting on a wall.............................................................................................................................................17

Connecting devices ...........................................................................................................................................................18

Sample setups .............................................................................................................................................................18

When used as webcam................................................................................................................................................19

Connecting the power supply ............................................................................................................................................20

Inserting/replacing the remote control batteries ................................................................................................................21

Pairing the device and remote control ...............................................................................................................................22

Making necessary initial settings.......................................................................................................................................23

Activating HDMI connection/DisplayLink function/Bluetooth/USB audio ......................................................................23

Installing the DisplayLink® driver onto your computer .................................................................................................23

Selecting the device on the computer ..........................................................................................................................24

Contents

CS-500 User Guide

Contents

Using smart devices in meetings ......................................................................................................................................25

What can be done with a Bluetooth connection ...........................................................................................................25

Making a Bluetooth connection ....................................................................................................................................25

Configuring the device from a TV screen (on-screen display menu)............................................26

Displaying the device’s settings menu ...............................................................................................................................26

Using software to configure and manage devices..........................................................................27

Using Yamaha CS Manager to specify detailed settings ...................................................................................................27

Using CS Remote Configurator to batch-configure devices ..............................................................................................27

Returning to factory default settings (factory reset).......................................................................28

Initializing by using the device...........................................................................................................................................28

Initializing by using Yamaha CS Manager .........................................................................................................................28

Appendix.............................................................................................................................................29

List of settings and operations...........................................................................................................................................29

Main specifications ............................................................................................................................................................30

CS-500 User Guide

Thank you for purchasing the Yamaha CS-500. This product is a video conferencing device equipped with a camera and

microphones. It can be set up for use in huddle spaces and meeting rooms. Combine it with a TV, speakers and video

conferencing software (computer) for comfortable teleconferencing.

Features/functions

Yamaha’s own high-quality audio processing

This device features audio processing functions required for video conferencing, including adaptive echo canceller (AEC),

noise reduction (NR) and automatic gain control (AGC). Camera framing area settings and beamforming microphones

focus on the speaker’s voice and suppress ambient sounds.

“SoundCap Eye™” achieves more comfortable remote communication

“SoundCap Eye” is a function that allows for comfortable remote communication, even in noisy

environments. By using the camera to automatically identify the surrounding conditions and conference

participants, more optimal sound pickup and output can be achieved.

-Face focus beamforming:

This technology picks up only the voice of the participant whose face is detected by the camera.

-Self-silence:

This technology automatically mutes the microphone when there is no human voice in the captured sound. This

prevents unwanted noise from reaching the remote party.

-Self-volume balancer:

This feature constantly adjusts the speaker volume to an appropriate volume depending on the surrounding noise.

Smart framing

With this function, the camera follows the subject according to the mode. The angle of view and zoom are automatically

adjusted onto the face detected by the camera. (Smart framing  Page 11)

-Group: Mode that frames all conference participants

-Speaker tracking: Mode that frames the person who is speaking

-Individual: Mode that frames the designated person

Easy connections via USB

This device and the computer can be connected with one USB cable. This makes it easy to set up and prepare for

meetings. (Sample setup  Page 18)

Automatically turning on/off the device

When the camera built into this device detects a person, the device automatically switches on from standby. (Auto wakeup)

Easy setup using the remote control and a display

You can display the menu on a TV and specify device settings by using the remote control. (On-screen display menu 

Page 26)

With the application software on the computer, more detailed settings can be specified. (Yamaha CS Manager  Page 27)

Introduction

CS-500 User Guide

Introduction

Available manuals

The manuals for this product can be downloaded in the PDF format from the following website.

About this manual

This manual uses the following signal words for important information.

• The illustrations as shown in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective

companies.

• Yamaha continuously makes improvements and updates to the software included in this product. You can download the

latest software from the Yamaha website.

• The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual,

access the Yamaha website then download the manual file.

Read This First (included) This describes what to do first after purchasing the product.

CS-500 Safety Guide (included) This contains the precautions for using this product safely.

CS-500 User Guide (this manual/PDF) This provides details on using this device. It also explains how to use

the Yamaha CS Manager application on your computer to configure

and operate the device.

On-Screen Display Menu Operation

Guide

This explains how to use the on-screen display menu (shown on a TV

screen) to configure this device.

Yamaha CS Manager Operation Guide This explains how to use the Yamaha CS Manager utility software on

your computer to configure and operate this device.

CS Remote Configurator Operation

Guide

This explains how to use the CS Remote Configurator utility software

to batch-configure multiple devices on the network.

WARNING This content indicates “risk of serious injury or death.”

CAUTION This content indicates “risk of injury.”

NOTICE Indicates content that you must observe in order to prevent the product from malfunctioning,

being damaged, or operating incorrectly, and to avoid data loss.

IMPORTANT Indicates content that you must know in order to operate and use the product correctly.

NOTE Indicates information that is related to operation and use. Read this for your reference.

 Yamaha website

U.S.A. and Canada:

https://uc.yamaha.com/support/

Other Countries:

https://download.yamaha.com/

CS-500 User Guide

Introduction

Included items

• CS-500 device

• Read This First

• Safety Guide

• USB 2.0 cable (Type-C to Type-A, 5 m)

• HDMI cable (2 m)

• Lens cap

• Remote control

• Coin battery (CR2032) × 2

• AC adaptor with power cord (CW2002100)

• Cable tie

Separately sold items

• Wall mounting bracket (mounting accessory) BRK-WL1

This is required for installing the device onto a wall. It is also used in combination with monitor mounting bracket

BRK-TV1 when installing the device onto a TV.

• Monitor mounting bracket (mounting accessory) BRK-TV1

This is used in combination with wall mounting bracket BRK-WL1 when installing the device onto the VESA mount of a

TV.

• USB cables: CBL-L10AC (10 meters), CBL-L25AC (25 meters)

These are fiber optic USB cables. They are used when the device and computer are far apart. These support USB 3.2

Gen2 (Super Speed Plus) and can communicate at high speeds up to 10 Gbps.

NOTE

The VESA standards are international and define the spacing between screw holes used when attaching video equipment,

such as TVs, to wall mounts and TV stands.

CS-500 User Guide

Introduction

Available utility software

This utility software can be used to set up the device according to its use and environment. The software can be

downloaded from the following website.

Related links

• Returning to factory default settings (factory reset) (Page 28)

• Connecting devices (Page 18)

1 2 3 4 5

CS-500 User Guide

Controls and connectors

Remote control

1Menu button

Can be used to display the on-screen display menu (Page 26) on the TV or pair the device with the remote control

(Page 22).

2Power button

Used to turn on/off the CS-500.

3Camera zoom button

Used to enlarge/reduce (zoom in/out) the video being captured.

4Pan/tilt button

Used to adjust the camera angle horizontally/vertically. It can also be used for Smart framing operations or moving the

cursor in the on-screen display menu displayed on the TV.

5Camera preseti 1 & 2 buttons

Two sets of PTZ (pan, tilt and zoom) settings can be saved and recalled. Long-press (for 2 seconds) this button to save

the settings adjusted with buttons 3 and 4. To recall, simply press the button.

6Smart framing button

Used to turn on/off Smart framingii.

7Speaker volume buttons

Used to turn up/down the volume of the speakers.

89 Microphone mute button

Used to turn on/off the microphone.

Top Bottom

CS-500 User Guide

Controls and connectors

i Camera preset

ii Smart framing

Camera preset/smart framing operability table

* [PTZ preset 1] and [PTZ preset 2] can be saved and recalled as camera presets 1 and 2 by using the remote control and

on-screen display menu.

PTZ (pan, tilt and zoom) camera presets can be saved for this device.

To save/change the PTZ settings, use the remote control, on-screen display menu or Yamaha CS Manager.

Specifying settings using the remote control

Refer to Page 10.

Specifying settings using the on-screen display menu or Yamaha CS Manager

Refer to the corresponding Operation Guide.

Depending on the mode, the angle of view is automatically adjusted and the selected subject framed.

[Group]: Mode where all persons in the group are framed

[Speaker tracking]: Mode where the person who is speaking is framed

[Individual]: Mode where a specific person is framed

*The target area for framing can be specified with the meeting area settings.

Specifying settings using the remote control

1 Use the (smart framing) button on the remote control to turn on smart framing.

2 Use the tilt (up/down) buttons to change the smart framing mode.

The currently selected framing mode appears in the notification badge on the screen.

-With the [Individual] mode, use the pan (left/right) buttons to select the person to be focused on.

-With the [Group] mode, the (camera zoom) button is deactivated.

Specifying settings using the on-screen display menu or Yamaha CS Manager

Refer to the corresponding Operation Guide.

Operation Remote control On-screen display

menu Yamaha CS Manager

Specifying meeting area settings — 

Turning on/off smart framing —

Selecting smart framing mode  

Saving/recalling camera presets 2 sets 2 sets 5 sets*

CS-500 User Guide

Procedure from connection to installation

Before starting work, determine the installation method for this device.

1. Connecting the power supply and turning on the device. (Page 20)

2. Inserting the batteries into the remote control. (Page 21)

3. Pairing the device and remote control. (Page 22)

4. Connecting the device. (Page 18)

> When used as a webcam. (Page 19)

5. Making necessary initial settings. (Page 23 to 25)

6. The computer screen will be displayed on the TV.

> If the computer screen does not appear on the TV, confirm the operations on page 23 to 24 again.

7. Installing the device.

> When installing on a TV. (Page 13)

> When mounting to a TV. (Page 14)

> When mounting on a wall. (Page 17)

Procedure for holding a meeting

Before the first time a computer connected to this device is used to hold a meeting, follow the steps below to check that the

computer screen is displayed on the TV and the audio is output.

* When this device is used as a webcam (Page 19), steps 3 to 5 are not necessary.

1. Turning on the computer.

2. Turning on this device with the remote control (or automatically starting it with auto wakeup).

3. The stand-by screen appears on the TV.

4. Connecting the computer to this device with a USB cable.

5. The computer screen will be displayed on the TV.

> If the computer screen does not appear on the TV. (Page 23)

6. Holding a meeting by using the video conferencing software.

> If sound is not output, select this device on the computer. (Page 24)

Specifying device settings

•On-screen display menu: (For all users) Specify device settings on a TV by using the remote control. (Page 26)

•Yamaha CS Manager: (For installers/administrators) Specify detailed settings for the device by using the application

software. (Page 27)

•CS Remote Configurator: (For installers/administrators) Batch-configure multiple devices (connected to a network) by

using the application software. (Page 27)

Procedures preparing for use

Installers of this device should read this.

Users of this device should read this.

CS-500 User Guide

Installing the device

When installing on a TV

This device can be placed directly on top of a TV.

1. Flip open the stand on the bottom of the device, and then hook it on the top of the TV.

2. Adjust the camera orientation (up or down) by changing the camera’s angle to the stand.

NOTE

When installing this device in the following situations, use the brackets to mount it to a TV. (Page 14)

• When installing more than 2 meters from the ground.

• When the TV thickness is 51 mm or more.

• When the stand of this device must be opened more than 90 degrees to place it on a TV.

• When the bottom of this device and the rubber part of the stand are not in close contact with the TV.

• When a stable installation of this device is not possible.

Setup and connections

CAUTION

• When installing on a TV, make sure that the device is no more than 2 meters from the ground.

When installing the device at a location more than 2 meters from the ground, be sure to use a

bracket to secure it to the TV. (Page 14)

• If the device falls, injuries or damage may result.

(back)

CS-500

Stand

CS-500 User Guide

Setup and connections

When mounting to a TV

This device can be mounted to a TV by using monitor mounting bracket BRK-TV1 and wall mounting bracket BRK-WL1

(both sold separately). When mounting this device to the top of the TV stand, prepare the following.

Items to prepare

1 Wall mounting bracket BRK-WL1 (sold separately)

• Wall mounting bracket

• Device fixing screw (1/4 inch) for wall mounting bracket × 1

2 Monitor mounting bracket BRK-TV1 (sold separately)

Compatible TV sizes: 48 to 60 inches (When mounting below the display: 48 to 70 inches)

• Monitor mounting brackets (for mounting onto wall mounting bracket, horizontal, and vertical)

•Spacer × 4

• Screw (M4 × 10 mm with washer) for bracket assembly × 12 (2 spare)

• Screws for mounting TV (M6 × 12 mm) × 4 and (M6 × 30 mm) × 4

• Spring washer and flat washer for screws (M6) for mounting TV × 4 each

• Screws for mounting TV (M8 × 15 mm) × 4 and (M8 × 35 mm) × 4

• Spring washer and flat washer for screws (M8) for mounting TV × 4 each

* Use only four of the above-listed screws for mounting TV.

3 TV stand (user provided)

4 Screwdriver (user provided)

IMPORTANT • For details on assembling the TV stand and mounting the TV to it, follow the instructions in the

manual for the TV stand.

• The TV should be mounted to the TV stand by two or more people.

WARNING

• Be sure to have the mounting bracket installed by the dealer where you purchased the

product or a professional contractor.

• After installation, make sure that the CS-500 is firmly secured. Also, regularly check that there

is no possibility of the device falling or tipping over. We cannot be held responsible for

accidents caused by incorrect installation.

• After installation, do not lean against the CS-500 or apply a strong force to it from above. If the

device falls, injuries or damage may result.

CS-500 User Guide

Setup and connections

The following is an example of an installation that uses the screw holes in the TV and a standard TV stand.

1. Attach the monitor mounting bracket (vertical), monitor mounting bracket (for mounting

onto wall mounting bracket) and the wall mounting bracket using the screws included with

them.

2. Using the included screws, attach the monitor mounting brackets (horizontal) and the

brackets assembled in step 1.

Align the monitor mounting brackets (horizontal) with the screw holes in the TV to determine the mounting position.

After determining the mounting position, mount the brackets from step 1 at the appropriate height.

IMPORTANT At this point, do not install the TV yet.

Monitor mounting

bracket (vertical)

Monitor mounting

bracket

Wall mounting

bracket

[Included with monitor mounting bracket]

Screw for bracket assembly

(M4 × 10 mm with washer) × 6

(back)

[Included with monitor mounting

bracket]

Screw for bracket assembly

(M4 × 10 mm with washer) × 4

Monitor mounting bracket (horizontal)

CS-500 User Guide

Setup and connections

3. Attach the brackets assembled in step 2 to the TV stand, TV and device.

1 Attach the brackets from step 2 to the TV stand.

2 From the underside of the wall mounting bracket, secure the device by using the included screw.

4. Adjust the camera orientation (up or down) by changing the camera’s angle to the stand.

IMPORTANT • Depending on the configuration of the TV stand, also tightly secure the spacers included with

monitor mounting bracket BRK-TV1.

• For details on assembling the TV stand and mounting the TV to it, follow the instructions in the

manual for the TV stand.

Spacer

TV stand

[Included with monitor mounting bracket]

Screws for mounting TV × 4

(M6 × 12 mm or 30 mm)

(M8 × 15 mm or 35 mm)

* Use screws matching the screw holes in the TV.

* When using spacers, use longer screws.

Device

Wall mounting bracket

[Included with wall mounting bracket]

Device fixing screw (1/4 inch) for wall

mounting bracket

CS-500 User Guide

Setup and connections

When mounting on a wall

This device can be mounted to a wall by using the wall mounting bracket (sold separately).

When mounting the device to a wall, prepare the following.

1 Wall mounting bracket BRK-WL1 (sold separately)

• Wall mounting bracket

• Device fixing screw (1/4 inch) for wall mounting bracket

2 Wall-mounting screws (user provided)

3 Screwdriver (user provided)

1. Attach the wall mounting bracket to the wall.

2. Secure the device to the bracket from step 1.

Place the device on the bracket from step 1. From the underside, secure the device to the wall mounting bracket by

using the included screw.

3. Adjust the camera orientation (up or down) by changing the camera’s angle to the stand.

WARNING

• Be sure to have the mounting bracket installed by the dealer where you purchased the product

or a professional contractor.

• After installation, make sure that the CS-500 is firmly secured. Also, regularly check that there

is no possibility of the device falling or tipping over. We cannot be held responsible for

accidents caused by incorrect installation.

• After installation, do not lean against the CS-500 or apply a strong force to it from above. If the

device falls, injuries or damage may result.

IMPORTANT • Screws for attaching the wall mounting bracket to the wall are not included. Prepare screws that

are strong enough.

• For details on screws and the installation, be sure to contact the dealer where you purchased

the product or a professional contractor.

Wall mounting

bracket

[Included with wall mounting bracket]

Device fixing screw (1/4 inch) for wall

mounting bracket

CS-500 User Guide

Setup and connections

Connecting devices

Sample setups

Use this connection method to output audio from the TV speakers. For video conferences, a computer connected to the

Internet can be used simply by connecting it to the device with a USB cable.

1Connect one end of the included HDMI cable to the [HDMI] port on the device, and connect the other end to the TV.

2Connect the Type-C plug of the included USB cable to the [USB] port on the device, and connect the Type-A plug to the

computer.

NOTE

• Be sure to first follow the procedure in “Activating HDMI connection/DisplayLink function/Bluetooth/USB audio” (Page 23).

• In order to display the computer screen on a TV, it may be necessary to install the DisplayLink® driver (Page 23).

Outputting audio through analog audio speakers/headphones

This device is equipped with a 3.5 mm audio output jack. Connect either headphones or speakers with a built-in amplifier to

output the audio of the remote party in a video conference.

NOTE

When connecting analog audio, select the [Enable 3.5mm analog audio connector] check box on the [Audio] screen in

Yamaha CS Manager, and then select either speakers or headphones. For details, refer to the Yamaha CS Manager

Operation Guide.

Device (CS-500)

USB cable

HDMI cable

AC adaptor

Computer

CS-500 User Guide

Setup and connections

When used as webcam

In order to be used only as a webcam for a video conferencing system, this device can be connected as shown in the

example below.

1Connect the Type-C plug of the included USB cable to the [USB] port on the device, and connect the Type-A plug to the

computer.

2Connect one end of the included HDMI cable to the computer, and connect the other end to the TV.

3Connect the speakerphone to the computer.

NOTE

When this device is used only as a webcam, the on-screen display menu (Page 26) cannot be used.

In addition, the following operations are not necessary.

• Activating HDMI connection/DisplayLink function/Bluetooth/USB audio (Page 23)

• Installing the DisplayLink driver (Page 23)

Device (CS-500)

USB cable

HDMI cable

AC adaptor

Computer/touchpanel console

USB cable

Speakerphone

CS-500 User Guide

Setup and connections

Connecting the power supply

Connect one end of the included AC adaptor to the [DC-IN] jack on the device, and connect the other end to an electrical

outlet.

Connecting the AC adaptor automatically turns on the device.

After the power supply has been connected, the device can be turned on or set to standby with the remote control.

AC adaptor

Pagina se încarcă ...

Yamaha CS-500 Manualul utilizatorului

Marca: Yamaha

Model: CS-500

Tip: Manualul utilizatorului

Descărcați PDF

raport

în alte limbi

français: Yamaha CS-500 Mode d'emploi
čeština: Yamaha CS-500 Uživatelská příručka
русский: Yamaha CS-500 Руководство пользователя
English: Yamaha CS-500 User guide
suomi: Yamaha CS-500 Käyttöohjeet
polski: Yamaha CS-500 instrukcja
Deutsch: Yamaha CS-500 Benutzerhandbuch
日本語: Yamaha CS-500 ユーザーガイド
italiano: Yamaha CS-500 Guida utente
español: Yamaha CS-500 Guía del usuario
svenska: Yamaha CS-500 Användarguide
dansk: Yamaha CS-500 Brugervejledning
português: Yamaha CS-500 Guia de usuario
Nederlands: Yamaha CS-500 Gebruikershandleiding

Yamaha CS-500 Manualul utilizatorului

Yamaha CS-500 Manualul utilizatorului

în alte limbi

Lucrări conexe