Indesit WIL 1000 OT Instructions For Use Manual

1

GB

English,1

Contents

Installation, 2-3

Unpacking and levelling

Electric and water connections

Technical details

Washing machine description, 4-5

Detergent dispenser

Control panel

Running a wash cycle, 6

Programme table, 7

Detergents and laundry, 8

Preparing your laundry

Special items

Load-balancing system

Precautions and advice, 9

General safety

Disposal

Saving energy and respecting the environment

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning your appliance

Cleaning the detergent dispenser

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

Before calling for Assistance

WASHING MACHINE

WIL 1000 OT

Instructions for use

GB

Français,13

F

Èeský,25

CZ

Polski,37

PL

Românã,49

RO CIS

ÐÓÑÑÊÈÉ,61

All manuals and user guides at all-guides.com

all-guides.com

2

GB

Installation

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the 3

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of

noise if the two front feet have not been adjusted

correctly.

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

A

All manuals and user guides at all-guides.com

3

GB

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (on the right);

 the supply voltage is included within the values i

ndicated on the Technical details table

(on the right);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

65 - 100 cm

Technical details

Model

WIL 1000 OT

Dimensions

59.5 cm wide

85 cm high

52.5 cm deep

Capacity

from 1 to 5 kg

Electric

connections

voltage 220/230 Volts 50 Hz

maximum absorbed power 1850 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 46 litres

Spin speed

up to 1000 rpm

Control

programmes

according to

IEC456 directive

programme ; TIMER knob "auto";

run with a load of 5 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96/CE

All manuals and user guides at all-guides.com

4

GB

Washing machine description

DETERGENT

DISPENSER

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent

won't necessarily make for a more efficient wash,

and may in fact cause build up on the interior of

your appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

Pre-wash detergent should only be used with the

sportswear programme

, while setting the timer

knob to the "auto" position or to one of the "3h" to

"24h" positions (see Detergents and laundry).

compartment 2: Detergent for the wash

cycle (powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

 Do not use hand wash detergent because it may

form too much foam.

1

2

3

CONTROL

PANEL

DOOR

KICKSTRIP

DOOR

HANDLE

ADJUSTABLE FEET

All manuals and user guides at all-guides.com

5

GB

Control panel

Detergent dispenser

ON-OFF

Button

START/CANCEL

Button

PROGRAMMES

Knob

TIMER

Knob

Indicator

lights

ON-OFF/

DOOR

LOCK

indicator light

Detergent dispenser: to add detergent and fabric

softener (see Washing machine description).

Indicator lights: show that the programme has

started and give an indication of the time remaining

until the end of the programme (see Running a

wash cycle).

PROGRAMME knob: to select the wash

programmes. The knob stays still during the cycle.

START/CANCEL button: starts the cycle after the

programme and required time have been set.

To cancel the programme and set a different one,

press and hold the button for at least 3 seconds.

ON-OFF/DOOR LOCK indicator light:

If the indicator light is switched on, this shows that

the door has been locked in order to prevent it being

opened accidentally; to avoid damaging the

machine, wait until the indicator light begins to flash

after the cycle has finished before opening the door.

The waiting time is approximately 2 minutes.

 If the ON-OFF/DOOR LOCK indicator light flashes

extremely rapidly it has experienced a problem (see

Troubleshooting).

ON/OFF button: to turn the washing machine on

and off.

TIMER knob: sets the required duration of the

programme.

In the "auto" position the duration is controlled

automatically by the machine.

All manuals and user guides at all-guides.com

6

GB

Running a wash cycle

Note: After installing the machine and before using

it for the first time, run an empty wash cycle using

detergent, setting the

programme and ensuring

the timer knob is in the "auto" position.

1. Switch the washing machine on by pressing

ON/OFF button

. All the LEDS will light up for a

few seconds and the ON-OFF/DOOR LOCK

indicator light

will begin to flash.

2. LOADING LAUNDRY. Open the door. Load the

laundry, making sure that the maximum load

quantity indicated in the table of programmes

(below) is not exceeded.

3. MEASURING OUT DETERGENT/WASHING ADDITIVES

Remove the drawer completely and pour the

detergent into the compartment marked with the

number 2. If required, pour fabric softener and

other additives into the compartment marked with

the number 3. The softener must not rise above

the level of the grille. If you wish to run the

washing programme especially for sportswear

(by setting the timer knob to "auto" or to one of

the positions between "3h and 24h" - see

Detergents and laundry), it is also possible to

use powder detergent in compartment 1 for the

pre-wash phase.

4. CLOSE THE DOOR.

5. SELECT THE WASH FABRIC by turning the

PROGRAMME KNOB right or left until the correct

fabric or the "Rinse" programme is selected.

6. SET THE WASHING END TIME by turning the

TIMER KNOB right or left.

The following settings may be used:

- Positions "30 min - 45 min - 60 min": by

selecting one of these times, the duration of the

programme is set.

- Positions between "3h" and "24h": by selecting

one of these times the user selects the number of

hours after which the programme should finish.

The effective duration of the wash is equivalent to

the "auto" cycle duration (see table of

programmes below), but the machine will delay

the start of the cycle automatically to ensure it

ends within the set time period.

- Whenever it is not necessary to set a specific

time for washing to end, select the "AUTO"

position: the machine automatically controls the

duration of the programme, based on the fabric

selected (see table of programmes below).

Regardless of the position selected for the TIMER

KNOB, the "Rinse"

programme lasts 30

minutes and begins as soon as the START/

CANCEL

button is pressed.

7. START THE PROGRAMME by pressing the

START/CANCEL

button. The "on-off/door lock"

and "programme in progress" indicator lights

will illuminate and remain lit constantly.

During the cycle, the indicator lights provide

information relating to the amount of time

remaining until the end of the programme.

When there are 30, 20 and 10 minutes

respectively remaining until the end of the

programme, the corresponding indicator lights will

illuminate.

8. PROGRAMME END

At the end of the wash programme, all the

indicator lights will switch off. Wait for the door to

become unlocked (the "on-off/door lock"

indicator light flashes), remove the laundry and

leave the door ajar in order to let the drum dry

out. Switch off the machine by pressing the ON/

OFF

button.

1

2

3

All manuals and user guides at all-guides.com

all-guides.com

7

GB

Programme table

* Note: regardless of the position of the "TIMER knob", the Rinse cycle begins immediately after the ON/CANCEL

button is pressed, and lasts for 30 minutes.

Important:

- the quick wash programmes "30 min" and "45 min" (regardless of the type of fabric) are recommended for

refreshing lightly soiled garments in a short time.

- the "60 min" programmes (regardless of the type of fabric) are recommended for washing lightly soiled garments.

- Wash times do not include the 2 minutes at the end of the cycle when the user must wait for the door to unlock.

Nature of fabrics

and soiling

Program-

mes

Times

Maximum

Load (kg)

Maximum

temperature

Wash cycle description

White cotton

auto (125 min.) 5 60°

Wash, rinse, intermediate and final spins

30 min.

45 min.

60 min.

3

40°

60°

3h - 24h 5 60°

Coloured cotton

auto (70 min.) 5

40° Wash, rinse, intermediate and final spins

30 min.

45 min.

60 min.

3

3h - 24h 5

Dark/delicate cotton

auto (60 min.) 5

30° Wash, rinse, intermediate and final spins

30 min.

45 min.

60 min.

3

3h - 24h 5

Synthetics

auto (60 min.) 2,5

40° Wash, rinse, gentle spin

30 min.

45 min.

60 min.

1,5

2,5

3h - 24h 2,5

Wool

auto (60 min.) 1

40° Wash, rinse, gentle spin

30 min.

45 min.

60 min.

1

3h - 24h 1

Delicates

auto (60 min.) 1

30° Wash, rinse, drain

30 min.

45 min.

60 min.

1

3h - 24h 1

Special Sport

auto (60 min.) 1,5

30° Prewash, wash, rinse, intermediate and final spins

30 min.

45 min.

60 min.

1,5

3h - 24h 1,5

Rinse

*

2,5 Rinse and spin

All manuals and user guides at all-guides.com

8

GB

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the maximum load values shown

in the "Programme table".

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 3 kg, repeating the rinse cycle

once or twice.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1 kg.

Sportswear: use the "Special Sport"

programme. It is possible to run an initial pre-wash

phase, which is useful for removing soil or mud

residues from the garments. To use this phase, pour

powder detergent into compartment 1 of the

detergent drawer (see Washing machine

description).

The pre-wash phase will not run if the timer knob is

set to a duration between 30 minutes and 1 hour

(inclusive).

Load-balancing system

To avoid excessive vibrations, before every spin

cycle the machine distributes the load in a uniform

manner by continuously rotating the drum at a

speed which is slightly faster than the normal

washing speed.

When, despite repeated attempts, the load is still

not evenly distributed, the machine spins at a lower

speed than the set frequency.

If the load is excessively unbalanced, the machine

attempts to distribute it instead of spinning.

The balancing attempts may extend the total duration

of the cycle, up to a maximum of 10 minutes.

Detergents and laundry

All manuals and user guides at all-guides.com

9

GB

Precautions and advice

 The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your washing machine only needs less

than half the amount of water to get the best results:

an objective reached to respect the environment.

Saving on detergent, water, energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. A full load instead of

two half loads allows you to save up to 50% on energy.

 Treating stains with a stain remover or leaving them

to soak before washing will cut down the need to

wash them at high temperatures.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

All manuals and user guides at all-guides.com

10

GB

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

All manuals and user guides at all-guides.com

11

GB

Troubleshooting

Your washing machine could fail to work. Before calling for Assistance (see Service), make sure the problem

can't easily be solved by consulting the following list.

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water.

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

The ON-OFF/DOOR LOCK

indicator light flashes

extremely rapidly.

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The ON/OFF button

has not been pressed.

 The START/CANCEL button

has not been pressed.

 The water tap is not turned on.

 A washing end time between "3h" and "24h" has been set

(see Running a wash cycle).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/CANCEL button

has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor (see Installation).

 The free end of the hose is underwater (see Installation).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

 The drain hose is bent (see Installation).

 The drain duct is clogged.

 When the machine is installed, the locking screws for the oscillating

assembly are still in place. Remove the screws (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is closed in between furniture cabinets and

the wall (see Installation).

 The water inlet hose is not screwed on correctly (see Installation).

 The detergent dispenser is obstructed (to clean it, see Care and maintenance).

 The drain hose is not secured properly (see Installation).

 This means there is a problem with the machine. Before calling

Assistance, please follow the set of instructions below:

1. Switch off the machine by pressing the

button;

2. Remove the plug connecting the appliance to the mains supply

and wait for at least 40 seconds;

3. Place the plug back into the socket;

4. Switch on the machine by pressing the

button again;

5. If the problem is still evident after this process has been carried

out, contact Assistance.

 The detergent is not suitable for machine washing (it should bear the

definition "for washing machines" or "hand and machine wash", or the like).

 You used too much detergent.

All manuals and user guides at all-guides.com

all-guides.com

12

GB

Before calling for Assistance:

 Check whether you can solve the problem on your own (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 If the machine has been installed or used incorrectly, you may be charged for the maintenance callout service.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service

All manuals and user guides at all-guides.com

13

F

Français

Sommaire

Installation, 14-15

Déballage et mise à niveau

Raccordements hydrauliques et électriques

Caractéristiques techniques

Description du lave-linge, 16-17

Tiroir à produits lessiviels

Bandeau de commandes

Comment effectuer un cycle de lavage, 18

Tableau des programmes, 19

Produits lessiviels et linge, 20

Triage du linge

Pièces de linge particulières

Système d'équilibrage du chargement

Précautions et conseils, 21

Sécurité générale

Mise au rebut

Economies et respect de l'environnement

Entretien et soin, 22

Coupure de l'arrivée d'eau et de courant

Nettoyage du lave-linge

Nettoyage du tiroir à produits lessiviels

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau d'arrivée de l'eau

Anomalies et remèdes, 23

Assistance, 24

Consultation à tout moment

LAVE-LINGE

WIL 1000 OT

Mode d'emploi

F

All manuals and user guides at all-guides.com

14

F

 Conservez ce mode d'emploi pour pouvoir le

consulter à tout moment. En cas de vente, de cession

ou de déménagement, veillez à ce qu'il suive toujours

le lave-linge pour que son nouveau propriétaire soit

informé sur son mode de fonctionnement et puisse

profiter des conseils correspondants.

 Lisez attentivement les instructions: elles fournissent

d'importantes informations sur l'installation, l'utilisation

et la sécurité.

Déballage et mise à niveau

Déballage

1. Déballez le lave-linge.

2. Contrôlez que le lave-linge n'a pas été endommagé

pendant le transport. S'il est abîmé, ne le raccordez

pas et contactez votre revendeur.

3. Enlevez les 3 vis de

protection pour le

transport, le

caoutchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Bouchez les trous à l'aide des bouchons plastique

fournis.

5. Conservez bien toutes ces pièces: il faudra les

remonter en cas de transport du lave-linge.

 Les emballages ne sont pas des jouets pour enfants.

Mise à niveau

Votre appareil peut s'avérer bruyant si vous n'avez

pas bien réglé ses deux pieds avant.

1. Installez le lave-linge sur un sol plat et rigide, sans

l'appuyer contre des murs, des meubles ou autre.

2. Si le sol n'est pas

parfaitement horizontal,

vissez ou dévissez les

petits pieds avant (voir

figure) pour niveler

l'appareil; son angle

d'inclinaison, mesuré

sur le plan de travail, ne

doit pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité de la

machine et évite qu'il y ait des vibrations, du bruit et

des déplacements en cours de fonctionnement. Si la

machine est posée sur de la moquette ou un tapis,

réglez les petits pieds de manière à ce qu'il y ait

suffisamment d'espace pour assurer une bonne

ventilation.

Raccordements hydrauliques et

électriques

Raccordement du tuyau d'arrivée de l'eau

1. Montez le joint A sur

l'extrémité du tuyau

d'alimentation et vissez-

le à un robinet d'eau

froide à embout fileté 3/4

gaz (voir figure).

Faites couler l'eau

jusqu'à ce qu'elle soit

limpide et sans

impuretés avant de

raccorder.

2. Raccordez le tuyau

d'alimentation au lave-

linge en le vissant à la

prise d'eau prévue, dans

la partie arrière en haut

à droite (voir figure).

3. Faites attention à ce que le tuyau ne soit ni plié ni

écrasé.

 La pression de l'eau doit être comprise entre les

valeurs indiquées dans le tableau des

Caractéristiques techniques (voir page ci-contre).

 Si la longueur du tuyau d'alimentation ne suffit pas,

adressez-vous à un magasin spécialisé ou à un

technicien agréé.

Installation

A

All manuals and user guides at all-guides.com

15

F

Raccordement du tuyau de vidange

Raccordez le tuyau

d'évacuation, sans le

plier, à un conduit

d'évacuation ou à une

évacuation murale

placés à une distance

du sol comprise entre

65 et 100 cm (voir figure);

ou bien accrochez-le à

un évier ou à une

baignoire, dans ce cas,

fixez le support en

plastique fourni avec

l'appareil au robinet

(voir figure). L'extrémité

libre du tuyau

d'évacuation ne doit

pas être plongée dans

l'eau.

 L'utilisation de tuyaux de rallonge est absolument

déconseillée, si vous ne pouvez vraiment pas faire

autrement vous devrez utiliser un tuyau de même

diamètre et de longueur maximum de 150 cm.

Branchement électrique

Avant de brancher la fiche dans la prise de courant,

contrôlez que:

 la prise dispose de mise à la terre et est conforme

aux normes;

 la prise est bien apte à supporter la puissance

maximale de la machine indiquée dans le tableau

des Carcatéristiques techniques (voir ci-contre);

 la tension d'alimentation est bien comprise entre les

valeurs figurant dans le tableau des

Caractéristiques techniques (voir ci-contre);

 la prise est bien compatible avec la fiche du lave-

linge. Autrement, remplacez la prise ou la fiche.

 Votre lave-linge ne doit pas être installé dehors,

même à l'abri, car il est très dangereux de le laisser

exposé à la pluie et aux orages.

 Après installation du lave-linge, la prise de courant

doit être facilement accessible.

 N'utilisez ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni écrasé.

 Le câble d'alimentation ne doit être remplacé que

par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non respect des normes énumérées ci-dessus.

65 - 100 cm

Caractéristiques techniques

Modèle

WIL 1000 OT

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 52,5 cm

Capacité

de 1 à 5 kg

Raccordements

électriques

tension 220-230 Volt 50 Hz

puissance maximale absorbée 1850 W

Raccordements

hydrauliques

pression maximale 1 MPa (10 bar)

pression minimale 0,05 MPa (0,5 bar)

capacité du tambour 46 litres

Vitesse

d'essorage

jusqu'à 1000 tours minute

Programmes de

contrôle selon la

norme IEC456

Programme ; Bouton DUREE "auto";

effectué avec une charge de 5 kg.

Cet appareil est conforme aux

Directives Communautaires suivantes:

- 73/23/CEE du 19/02/73 (Basse

Tension) et modifications suivantes

- 89/336/CEE du 03/05/89

(Compatibilité électromagnétique) et

modifications suivantes

- 2002/96/CE

All manuals and user guides at all-guides.com

16

F

Description du lave-linge

TABLEAU DE

COMMANDE

HUBLOT

PLINTHE

PIEDS RÉGLABLES

POIGNÉE

HUBLOT

TIROIR À PRODUITS

LESSIVIELS

Tiroir à produits lessiviels

Un bon résultat de lavage dépend aussi d'un bon

dosage de produit lessiviel: un excès de lessive ne

lave pas mieux, il incruste l'intérieur de votre lave-

linge et pollue l'environnement.

Sortez le tiroir à produits

lessiviels et versez la

lessive ou l'additif

comme suit.

bac 1: Lessive prélavage (en poudre)

N'utilisez le produit lessiviel de prélavage qu'en cas

de sélection du programme dédié aux vêtements de

sport

, amenez le bouton durée sur la position

"auto" ou sur une des positions de "3h à 24h"

(voir «Produits lessiviels et linge»).

bac 2: Lessive lavage

(en poudre ou liquide)

Versez la lessive liquide juste avant la mise en marche.

bac 3: Additifs (adoucissant, etc.)

L'assouplissant ne doit pas déborder de la grille.

 N'utilisez pas de lessives pour lavage à la main,

elles génèrent trop de mousse.

1

2

3

All manuals and user guides at all-guides.com

all-guides.com

17

F

Bandeau de commandes

Tiroir à produits lessiviels: chargement des

produits lessiviels et additifs (voir Description du

lave-linge).

Voyants: ils indiquent le début du programme et le

temps restant (voir Comment effectuer un cycle de

lavage).

Bouton PROGRAMMES: choix des programmes

(voir page 7).

En cours de lavage, le bouton ne bouge pas.

Touche MARCHE / PAUSE: pour démarrer le cycle

après avoir sélectionné le programme et la durée

voulue.

Pour annuler le programme et en sélectionner un

autre, appuyez au moins 3 secondes de suite sur la

touche.

Voyant

ALLUMAGE/HUBLOT VERROUILLE

:

Le voyant allumé indique que le hublot est verrouillé

pour empêcher toute ouverture accidentelle ;

attendez que le voyant cesse de clignoter avant

d'ouvrir le hublot, vous risqueriez autrement

d'endommager l'appareil.

Le délai d'attente est d'environ 2 minutes.

 Un clignotement très rapide du voyant

ALLUMAGE/HUBLOT VERROUILLE signale une

anomalie (voir Anomalies et remèdes).

Tiroir à produits lessiviels

Touche

MISE EN

MARCHE/ARRET

Bouton

PROGRAMMES

Bouton

DUREE

Voyants

Voyant

ALLUMAGE/

HUBLOT

VERROUILLE

Touche MISE EN MARCHE/ARRET: mise en

marche ou arrêt du lave-linge.

Bouton DUREE: pour sélectionner l'heure de fin de

programme.

En position "auto" la durée du programme est gérée

automatiquement par l'appareil.

Touche

MARCHE / PAUSE

All manuals and user guides at all-guides.com

18

F

Comment effectuer un cycle de

lavage

Remarque: Après avoir installé l'appareil et

avant sa première utilisation, effectuez un cycle de

lavage à vide avec un produit lessiviel et

sélectionnez le programme

en amenant le

bouton Durée en position "auto".

1. Pour allumer le lave-linge appuyez sur la touche

MARCHE/ARRET

. Tous les voyants s'allument

pendant quelques secondes puis s'éteignent et le

voyant ALLUMAGE/HUBLOT VERROUILLE

commence à clignoter.

2. CHARGER LE LINGE. Ouvrez le hublot. Chargez

le linge en faisant attention à ne pas dépasser la

charge maximale indiquée dans le tableau des

programmes à la page suivante.

3. DOSER LE PRODUIT LESSIVIEL/ADDITIFS

Sortez complètement le tiroir et versez le produit

lessiviel dans le bac n° 2. Versez l'assouplissant et

autres additifs éventuels dans le bac n° 3.

L'assouplissant ne doit pas déborder de la grille.

Si vous souhaitez effectuer un programme de

lavage spécial vêtements de sport

, amenez le

bouton Durée sur la position "auto" ou sur une

des positions comprises entre "3h et 24h" (voir

Produits lessiviels et linge) et introduisez de la

lessive en poudre pour prélavage dans le bac n°1.

4. FERMER LE HUBLOT.

5. Pour SELECTIONNER LE TEXTILE, tournez le

BOUTON PROGRAMMES à droite ou à gauche

jusqu'à ce que vous ayez sélectionné le textile

désiré ou le programme "Rinçage".

6. Pour SELECTIONNER LA FIN DE LAVAGE,

tournez le BOUTON DUREE à droite ou à gauche.

Sélections possibles:

- Positions "30 min - 45 min - 60 min": la

sélection d'une de ces positions détermine la

durée du programme sélectionné.

- Positions de "3h" à "24h": la sélection d'une de

ces positions détermine le nombre d'heures au

bout desquelles le programme de lavage prend

fin. La durée effective du lavage est égale à celle

du cycle "auto" (voir tableau programmes page

suivante) mais l'appareil diffèrera

automatiquement le démarrage du cycle pour

assurer sa conclusion dans le délai fixé.

- Si la sélection d'une durée spéciale de lavage

n'est pas nécessaire, sélectionnez la position

"AUTO": l'appareil gèrera automatiquement la

durée du programme selon le textile sélectionné

(voir tableau programmes page suivante).

Indépendamment de la position sélectionnée sur

le BOUTON DUREE, le programme "Rinçage"

dure 30 minutes et démarre immédiatement dès

pression sur la touche MARCHE / PAUSE

.

7. Pour DEMARRER LE PROGRAMME, appuyez sur

la touche MARCHE / PAUSE

. Les voyants

"allumage/hublot verrouillé"

et "programme en

cours"

s'allument.

Pendant le cycle, les voyants indiquent le temps

restant.

Quand il manque respectivement 30, 20 et 10

minutes à la fin du programme, les voyants

correspondants s'allument.

8. FIN DU PROGRAMME

A la fin du programme de lavage, tous les voyants

s'éteignent. Attendez le déverrouillage du hublot

(voyant "allumage/hublot verrouillé"

clignotant),

sortez le linge et laissez le hublot entrouvert pour

faire sécher le tambour. Eteignez l'appareil à l'aide

de la touche MARCHE/ARRET

.

1

2

3

All manuals and user guides at all-guides.com

19

F

Tableau des programmes

Nature des textiles

et degré de

salissure

Program-

mes

Durée

Charge

maxi. (kg)

Te m p é r a t u r e

maxi.

Description du cycle de lavage

Coton blancs

auto (125 min.) 5 60°

Lavage, rinçages, essorages intermédiaires et essorage final

30 min.

45 min.

60 min.

3

40°

60°

3h - 24h 5 60°

Coton couleursi

auto (70 min.) 5

40° Lavage, rinçages, essorages intermédiaires et essorage final

30 min.

45 min.

60 min.

3

3h - 24h 5

Coton

foncés/délicats

auto (60 min.) 5

30° Lavage, rinçages, essorages intermédiaires et essorage final

30 min.

45 min.

60 min.

3

3h - 24h 5

Synthétiques

auto (60 min.) 2,5

40° Lavage, rinçages et essorage délicat

30 min.

45 min.

60 min.

1,5

2,5

3h - 24h 2,5

Laine

auto (60 min.) 1

40° Lavage, rinçages et essorage délicat

30 min.

45 min.

60 min.

1

3h - 24h 1

Délicats

auto (60 min.) 1

30° Lavage, rinçages et essorage

30 min.

45 min.

60 min.

1

3h - 24h 1

Spécial Sport

auto (60 min.) 1,5

30°

Prélavage, lavage, rinçages, essorages intermédiaires et

essorage final

30 min.

45 min.

60 min.

1,5

3h - 24h 1,5

Rinçage

*

2,5 Rinçages et essorage

* Remarque: indépendamment de la position du "bouton DUREE", le Rinçage démarrera immédiatement dès

pression sur la touche MARCHE/ARRET et durera 30 minutes.

Important:

- les programmes rapides "30 min" et "45 min" (indépendamment du type de textile) sont conseillés pour

rafraîchir du linge peu sale en peu de temps.

- les programmes "60 min" (indépendamment du type de textile) sont conseillés pour laver du linge peu sale.

- les 2 minutes d'attente nécessaires au déverrouillage du hublot ne sont pas comprises dans les temps

indiqués.

All manuals and user guides at all-guides.com

20

F

Triage du linge

 Triez correctement votre linge d'après:

- le type de textile / le symbole sur l'étiquette.

- les couleurs: séparez le linge coloré du blanc.

 Videz les poches et contrôlez les boutons.

 Ne dépassez pas la charge maximale indiquée

dans le "Tableau des programmes".

Combien pèse le linge ?

1 drap 400-500 g

1 taie d'oreiller 150-200 g

1 nappe 400-500 g

1 peignoir 900-1.200 g

1 serviette éponge 150-250 g

Pièces de linge particulières

Rideaux: pliez-les bien et glissez-les dans une taie

d'oreiller ou dans un sac genre filet. Lavez-les seuls

sans dépasser la demi-charge. Sélectionnez le pro-

gramme

qui supprime automatiquement l'essorage.

Doudounes et anoraks: s'ils sont en duvet d'oie ou

de canard, ils peuvent être lavés à la machine. Lavez

les vêtements sur lenvers. La charge ne doit pas

excéder

2-3 kg. Prévoyez 2, voire 3 rinçages.

Laine: pour obtenir d'excellents résultats utilisez un

produit lessiviel spécial et ne dépassez pas une

charge de 1kg.

Vêtements de sport: utilisez le programme "Spé-

cial Sport"

. Un prélavage est possible pour élimi-

ner les résidus de terre et de boue sur les vête-

ments. Dans ce cas, introduisez de la lessive en

poudre dans le bac n° 1 du tiroir à produits lessiviels

(voir «Description du lave-linge»).

La phase de prélavage n'aura pas lieu si la sélection

effectuée à l'aide du bouton Durée est comprise

entre 30 min et 1h.

Système d'équilibrage du chargement

Pour éviter des vibrations excessives, avant toute

phase d'essorage, l'appareil imprime au tambour

une série de rotations continues à une vitesse

légèrement supérieure à la vitesse de lavage pour

distribuer le linge de façon uniforme.

Si, malgré plusieurs tentatives, le linge n'est pas

parfaitement réparti, l'appareil effectue l'essorage à

une vitesse inférieure à la vitesse prévue.

En cas de déséquilibre excessif, l'appareil procède à

la répartition du linge au lieu de l'essorage.

Les tentatives éventuelles d'équilibrage peuvent

prolonger la durée totale du cycle de 10 minutes

maximum.

Produits lessiviels et linge

All manuals and user guides at all-guides.com

Pagina se încarcă ...

Indesit WIL 1000 OT Instructions For Use Manual

Indesit WIL 1000 OT Instructions For Use Manual

în alte limbi

Lucrări conexe

Alte documente