Yamaha SV120S Manualul proprietarului

Marca
Yamaha
Model
SV120S
Tip
Manualul proprietarului
1
Thank you for purchasing the Yamaha Silent Violin. In order to obtain the maxi-
mum performance and enjoyment from your Silent Violin, we urge you to read
this Owner’s Manual thoroughly before using the instrument. Please keep this
Owner’s Manual in a safe place for later reference.
Precautions.................................................................... 3
Main Body/Accessories ................................................ 4
Nomenclature ................................................................ 5
Setup .............................................................................. 7
Tuning ......................................................................................... 7
The Shoulder Rest ...................................................................... 8
The Bow (supplied with the SV120S) ......................................... 8
Changing Strings ........................................................................ 8
Power Supply ............................................................... 10
Using Batteries ......................................................................... 10
Supplying AC Power ................................................................. 10
Using the Controls ...................................................... 11
The Reverb................................................................... 11
Connecting External Devices..................................... 12
AUX IN jack .............................................................................. 13
LINE OUT jack .......................................................................... 13
Specifications .............................................................. 14
Congratulations!
SV120/SV120S
Owner’s Manual
Contents
English
02_sv120_e_r2.pm 08.7.14, 9:31 AM1
2
SPECIAL MESSAGE SECTION
92-BP
This product utilizes batteries or an external power supply (adaptor). DO NOT
connect this product to any power supply or adaptor other than one described
in the manual, on the name plate, or specifically recommended by Yamaha.
This product should be used only with the components supplied or; a cart,
rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please
observe all safety markings and instructions that accompany the accessory
product.
SPECIFICATIONS SUBJECT TO CHANGE: The information
contained in this manual is believed to be correct at the time of printing. However,
Yamaha reserves the right to change or modify any of the specifications without
notice or obligation to update existing units.
Do not attempt to service this product beyond that described in the user-
maintenance instructions. All other servicing should be referred to qualified
service personnel.
This product, either alone or in combination with an amplifier and headphones
or speaker/s, may be capable of producing sound levels that could cause
permanent hearing loss. DO NOT operate for long periods of time at a high
volume level or at a level that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
NOTICE: Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the owner’s
responsibility. Please study this manual carefully and consult your dealer
before requesting service.
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that
are both user safe and environmentally friendly. We sincerely believe that our
products and the production methods used to produce them meet these goals.
In keeping with both the letter and the spirit of the law, we want you to be
aware of the following:
Battery Notice: This product MAY contain a small non-rechargeable
battery which (if applicable) is soldered in place. The average life span of this
type of battery is approximately five years. When replacement becomes
necessary, contact a qualified service representative to perform the replace-
ment.
This product may also use “household” type batteries. Some of these may be
rechargeable. Make sure that the battery being charged is a rechargeable type
and that the charger is intended for the battery being charged.
When installing batteries, do not mix old batteries with new, or with batteries
of a different type. Batteries MUST be installed correctly. Mismatches or
incorrect installation may result in overheating and battery case rupture.
Warning: Do not attempt to disassemble or incinerate any battery. Keep all
batteries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of household
type batteries in your area for battery disposal information.
Disposal Notice: Should this product become damaged beyond repair, or
for some reason its useful life is considered to be at an end, please observe all
local, state, and federal regulations that relate to the disposal of products that
contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please
contact Yamaha directly.
NAMEPLATE LOCATION: The nameplate is located on the bottom of the
product. The model number, serial number, power requirements, etc., are
located on this plate. You should record the model number, serial number, and
the date of purchase in the spaces provided below and retain this manual as a
permanent record of your purchase.
Model Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
FCC INFORMATION (U.S.A.)
other electronic devices. Compliance with FCC regulations does not
guarantee that interference will not occur in all installations. If this
product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to
eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to
co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you cannot locate the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA 90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high-quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable
level of assurance that your use of this product in a residential
environment will not result in harmful interference with other
electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the user’s manual, may cause interference harmful to the operation of
CANADA
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS
SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX
APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE
PAR LE MINISTERE DES COMMUNICATIONS DU CANADA.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
02_sv120_e_r2.pm 08.7.14, 9:31 AM2
3
Your Silent Violin will give you years of reliable service if you follow the simple rules
given below:
Location
Do not expose it to the following conditions to
avoid deformation, discoloration, or more seri-
ous damage.
Direct sunlight (e.g. near a window).
High temperatures (e.g. near a heat source, out-
side, or in a car during the daytime).
Excessive humidity.
Excessive dust.
Strong vibration.
Power Supply
Turn the power switch OFF when not in use.
If you use an AC power adaptor, unplug the adap-
tor from the AC outlet if not to be used for an
extended period of time.
Unplug the AC power adaptor during electric
storms.
Avoid plugging the AC power adaptor into the same
AC outlet as appliances with high power consump-
tion, such as electric heaters or ovens. Also avoid
using multi-plug adaptors since these can result in
reduced sound quality and possibly damage.
Turn Power OFF When Making Connections
To avoid damage to the Silent Violin and other
devices to which it is connected (a sound system,
for example), turn the power switches of all related
devices OFF prior to connecting or disconnecting
audio cables.
Handling and Transport
Never apply excessive force to the controls, con-
nectors or other parts.
Always unplug cables by gripping the plug firmly,
not by pulling on the cable.
Disconnect all cables before moving the unit.
Physical shocks caused by dropping, bumping, or
placing heavy objects on the unit can result in
scratches and more serious damage.
Cleaning
Clean the cabinet and panel with a dry soft cloth.
•A slightly damp cloth may be used to remove
stubborn grime and dirt.
Never use cleaners such as alcohol or thinner.
Avoid placing vinyl objects on top of the unit (vinyl
can stick to and discolor the surface).
Electrical Interference
This unit contains electric circuitry and may cause
interference if placed too close to radio or television
receivers. If this occurs, move it further away from
the affected equipment.
YAMAHA is not responsible for damage
caused by improper handling or operation.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points, in accordance with your national legislation and the Directives 2002/
96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
02_sv120_e_r2.pm 08.7.14, 9:31 AM3
4
Main Body/Accessories
After opening the packaging, please check that all the parts listed below are in-
cluded.
SV120
• Violin
SV120
Bridge
SUM-3 (AA) size
Manganese batteries x2
* The supplied battery is for
demonstration purposes.
Audio cable
Stereo earphones
The following items are in addition to the SV120 package.
Bow : 4/4 size
• Hard case
SV120S
Shoulder rest : KUN Yamaha Special
Rosin : PIRASTRO Schwarz 9005
02_sv120_e_r2.pm 08.7.14, 9:31 AM4
5
Nomenclature
Front
Tuning peg
Nut
Neck
Fingerboard
4th string (G)
2nd string (A)
3rd string (D)
1st string (E)
Frame
Body
Bridge
Bridge seat
Adjuster
Tailpiece
Chin rest
02_sv120_e_r2.pm 08.7.14, 9:31 AM5
6
Controls
VOLUME
DC-IN 9-12V jack
(Power adaptor connector)
PHONES jack (Stereo earphones) : Stereo mini type
LINE OUT jack : Stereo mini type
AUX IN jack : Stereo mini type
AUX VOL (AUX volume)
Stereo phone/stereo mini
plug converter
LINE OUT jack : Standard stereo phone type
Stereo phone/stereo mini plug converter
POWER switch
REV. ON/ON/OFF
REVERB switch
ROOM/HALL 1/HALL 2
Lamp
02_sv120_e_r2.pm 08.7.14, 9:31 AM6
7
Setup
Tuning
The Silent Violin is shipped from the factory with the bridge unfitted. First, set up
the bridge and then proceed with tuning.
•The lower side of the bridge supports the 1st string
(E), the higher side supports the 4th string (G).
Make sure the bridge is placed properly, then set the
bridge in the bridge seat. The side of the bridge with
the AUBERT logo should face the tailpiece.
Ensure that the bridge stands vertically. If it leans to
one side, use both hands to adjust. Make sure that
each string passes over the corresponding slits in
the bridge.
•The strings are tuned to the following pitches. The
1st string is tuned to E, the 2nd string to A, the 3rd
string to D, and the 4th string to G.
Use a piano, tuning fork, tuner, etc., and adjust the
pitch of each string using the tuning pegs. When
rotating the peg, apply firm pressure towards the head
stock.
4th string
1st string
Slit
[Looking from the tailpiece]
Properly aligned
Escutcheon
Tailpiece
Poor alignment
Poor alignment
[Bridge is placed vertically]
After tuning is complete, make sure the bridge is
still properly aligned. If the bridge is leaning in ei-
ther direction, slightly loosen the strings and care-
fully re-align the bridge using both hands.
•Finally, use the adjuster to fine tune the strings.
If the adjuster is too loose,
it could produce noise while
playing.
Caution
Don’t loosen too much.
G
D
A
E
Body
02_sv120_e_r2.pm 08.7.14, 9:31 AM7
8
The Shoulder Rest
The shoulder rest accessory is supplied to give
you added support when holding the violin be-
tween your shoulder and chin. Refer to the illus-
tration and insert the shoulder rest into the holes
provided (on the rear of the instrument) to suit
your playing position.
If the instrument can be held comfortably without
the shoulder rest, the use of the rest won’t be nec-
essary.
The pins on the shoulder rest slightly point outward.
When you attach the shoulder rest, insert one pin
about half way into its hole, and then slightly bend
the shoulder rest so that the second pin aligns with
the corresponding hole, and insert.
Shoulder rest
The Bow (supplied with the SV120S)
•Apply rosin to the bow hairs before using. Before using the bow for the first time, apply rosin carefully
and evenly to the whole bow. From the 2nd time, apply a small amount of rosin to the bow hairs.
Loosen the bow whenever the bow is not used.
If the bow is not used for an extended period of time, the hairs may suffer damage caused by insects.
Please treat with care.
Rotate the screw to adjust
the bow’s tension.
Bow hair
Changing Strings
As the strings get old, sound quality will gradually decrease, and it will become difficult to tune
the instrument. Change the strings as soon as you think they are getting old.
Winding the Strings
The adjuster should be set
to the middle of its adjust-
ment range.
1
Before you string the instrument, set the adjuster
so that it is in the middle of its adjustment range.
(All adjusters)
Pins
The end of the strings are sharp and can cut fingers. Use caution when changing strings.
When changing or adjusting strings, do not put your face close to the instrument. The string may
suddenly break resulting in eye or other unexpected injuries.
02_sv120_e_r2.pm 08.7.14, 9:31 AM8
9
Caution
2
Place the ball (on the end of the string) in the
notch on the adjuster. Make sure the ball is prop-
erly inserted in the adjuster’s notch.
3
Insert the other end of the string into the hole
on the tuning peg. Ensure that the string is wound
on the right side of the hole for the 1st (E) and
2nd (A) strings, and on the left side of the hole
for the 3rd (D) and 4th (G) strings. Next, check
the bridge does not fall over as you wind the
strings. Ensure that the strings pass over the cor-
responding slits on the top of the bridge. (Make
sure that the bridge is standing vertically.)
The 1st string (E) has a protective tube on it.
Make sure the tube is placed on the bridge as
shown in the illustration.
4
Use a piano, tuning fork, tuner, etc., and adjust
the pitch of each string using the tuning pegs.
5
Finally, use the adjuster to fine tune the strings.
Adjuster’s notch
Ball
Ball
String
Wound to the left
Wound to the right
3rd string (D)
2nd string (A)
Rotate the
tuning peg
as shown
Rotate the
tuning peg
as shown
1st string (E)
4th string (G)
If the adjuster is too loose, it could
produce noise while playing.
Don’t loosen too much.
1st string (E) protective tube.
Adjuster
When the instrument is not going to be used for an extended period of time, loosen the strings until
the pitch drops a whole tone.
02_sv120_e_r2.pm 08.7.14, 9:31 AM9
10
Power Supply
The Silent Violin can be operated with either battery or AC power. Always turn the
power switch (OFF/ON/REV.ON) on the rear panel OFF before making AC power
connections or replacing batteries.
Using Batteries
Battery compart-
ment cover
SUM-3 (AA)
size battery x2
Slide the POWER switch to the ON position, the lamp will light green. Slide the switch
to the REV. ON position, the lamp will flash red. When battery power is low, the lamp’s
color changes to orange, the sound becomes distorted, the Reverb does not prop-
erly function, and noise becomes audible. When one of these symptoms appears,
take note of the following cautions and replace the batteries.
•Always follow the +/– signs when inserting the batteries. Improper insertion may result in fire.
•Always replace worn batteries with a complete set of new batteries. Never mix new and old batteries.
Do not mix different types of batteries (alkaline and manganese, or batteries from different manufac-
turers, or different types by the same manufacturer). Doing so may result in fire.
Supplying AC Power
AC adaptor is optional, please purchase the optional power adaptor PA-3C or PA-3B.
1
Plug the adaptor’s DC output cable into the Silent Violin’s DC IN 9-12V jack located on the side of
the instrument, making sure it is firmly inserted into the jack.
2
Plug the AC adaptor into a convenient wall AC power socket.
Battery power is automatically disconnected when the AC adaptor is connected.
When using an AC adaptor, make sure you use only the appointed compatible adaptor. The use of an
incompatible adaptor may result in damage to the instrument or cause fire, etc. Please use with
caution.
1
Open the battery compartment situated on the back
of the Silent Violin.
2
Insert the two batteries supplied (SUM-3 (AA)
size). Take careful note of the polarity markings as
shown in the illustration above, and insert the bat-
teries.
3
Replace the battery compartment cover.
•To prevent possible damage to the unit due to battery leakage and unnecessary power drain, remove
the batteries from the unit when it is not going to be used for an extended period of time.
The supplied battery is for demonstration purposes.
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
* For customers in the Netherlands.
02_sv120_e_r2.pm 08.7.14, 9:31 AM10
11
Using the Controls
1
Slide the POWER switch, located on the rear of the
instrument, to its ON position. The lamp will light
green.
2
Connect the stereo earphones to the PHONES jack
on the side of the instrument, make sure that the L
& R side earphones are used in the correct ears.
3
Rotate the VOLUME dial to the desired playing
level.
Do not operate at high volume levels when using earphones.
Doing so can lead to irreparable damage to your hearing.
Lights green
Lights red
The Reverb
The Silent Violins incorporates Yamaha’s
DSP reverb technology. Play while trying out
the three types of reverb.
1
Slide the POWER switch to the REV. ON position,
the lamp will light red, and reverb will be applied to
the Silent Violin’s sound.
2
Slide the REVERB switch to select one of the three
reverb modes.
•ROOM mode ........ this reverb simulates the natural reverberation found in a room.
HALL 1 mode ...... this reverb simulates the natural reverberation found in a hall.
HALL 2 mode ...... the same reverb simulation as HALL 1 but with a longer decay time.
02_sv120_e_r2.pm 08.7.14, 9:31 AM11
12
Connecting External Devices
3
Silent Violin
Stereo Earphones
SUM-3 (AA)
size battery x2
or
Power Adaptor
(Option)
Electric
Outlet
DC-IN 9-12V
From the LINE
OUT jack, etc.
CD Player
MD Player
Cassette Player
Electronic Metronome
To the AUX IN jack,
etc.
Audio Amp m Speaker
Electronic Tuner
PHONES
LINE OUT
AUX IN
P.A. Mixer, Recording Mixer
02_sv120_e_r2.pm 08.7.14, 9:31 AM12
13
AUX IN jack
•The AUX IN jack, located on the side of the
instrument, can be used to connect an external
stereo signal source to the Silent Violin.
Connecting the audio output of a CD player,
cassette player, etc. to the instrument allows you
to play along with the external audio source.
•The AUX IN jack’s signal level can be controlled
with the AUX. VOL control.
•The stereo phone/stereo mini plug converter
connected to the LINE OUT jack, can also be
connected to the AUX IN jack. This allows you
to connect a standard stereo (mono) phone plug
to the AUX IN jack.
LINE OUT jack
The LINE OUT jack, located on the side panel,
delivers the stereo signal of the Silent Violin to
external audio equipment.
Use an audio cable to connect the instrument to
the audio input jack of external speakers, mixing
console, cassette player, etc. to listen from exter-
nal audio equipment or recording. You can also
connect this jack to the INPUT jack on an elec-
tronic tuner and tune the Silent Violin like an elec-
tronic instrument using the instrument’s output
signal.
•When you purchased the Silent Violin (factory
set), the stereo phone/stereo mini plug converter
is connected to the LINE OUT mini jack. This
allows you to connect a standard stereo (mono)
phone plug to the LINE OUT jack.
•The stereo phone/stereo mini plug converter can
also be connected to the PHONES jack. This al-
lows you to connect a pair of headphones that are
only equipped with a standard phone plug to the
PHONES jack.
Before connecting the Silent Violin to any external devices, make sure that the power of all
related devices is turned OFF. Set the volume level of any external audio sources to the mini-
mum level before connecting anything. High volume settings could cause damage to the equip-
ment and your hearing.
If a connection cord is unplugged while the power is ON, it may result in damage to the equip-
ment. The sudden shock to your ears may be great, so please use with care.
Be careful not to step on the cord. The cord may break, equipment may be damaged, and this
may cause a substantial shock to your ears.
The signal from the Silent Violin’s output jacks must NEVER be returned to the AUX IN jack,
either directly or through external equipment. Doing so will result in feedback which may
cause damage to the internal electronics.
Commercially available mini plug cables sometimes are equipped
with plugs featuring a larger base (grip) diameter (see A in illus-
tration on the right) which may cause faulty contact when used
with this instrument.
Please make sure to use a audio cable identical to the one sup-
plied with the instrument.
A
02_sv120_e_r2.pm 08.7.14, 9:31 AM13
14
Specifications
Neck Hard Maple
Body Spruce
Fingerboard/Tuning Pegs Ebony
Bridge Hard Maple (Aubert)
Frame/Chin Rest/Tailpiece ABS Resin
Adjuster 4 pieces (Wittner)
Strings Ball-end type
Sensor Piezo pick-up (underneath the bridge)
Connectors/Controls Headphone Output
•AUX IN (w/Volume Control)
LINE OUT
•Volume
Reverb Switch (ROOM/HALL 1/HALL 2)
•POWER Switch (OFF/ON/REV. ON)
Power SUM-3 (AA) size battery x2 / AC Adaptor (PA-
3C or PA-3B) dual power source
Battery Life (Continuous Use)
Using Manganese batteries
Without Reverb (POWER Switch “ON”) approximately 15 hours
With Reverb (POWER Switch “REV. ON”) approximately 2.5 hours
Using Alkaline batteries
Without Reverb (POWER Switch “ON”) approximately 36 hours
With Reverb (POWER Switch “REV. ON”) approximately 10 hours
String Length 328 mm (12-15/16”)
Dimensions 587 (L) x 195 (W) x 110 (H) mm
23-1/8” (L) x 7-11/16” (W) x 4-5/16” (H)
Weight (with batteries) 690g (1 lbs. 8 oz.)
* Design and specifications are subject to change without notice.
02_sv120_e_r2.pm 08.7.14, 9:31 AM14
/

Acest manual este, de asemenea, potrivit pentru