Yamaha YST-RSW300 Manualul proprietarului

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

Printed in Indonesia WK23280

G

YST-RSW300

SUBWOOFER SYSTEM

ENCEINTE A CAISSON DE GRAVE

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

YST-RSW300

0101YST-RSW300_cv01_en.fm Page 1 Thursday, February 1, 2007 2:31 PM

i En

Thank you for selecting this Yamaha subwoofer system.

Please read the following operating precautions before use.

Yamaha will not be held responsible for any damage and/or injury

caused by not following the cautions below.

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install this unit in a cool, dry, clean place - away from windows,

heat sources, sources of excessive vibration, dust, moisture and

cold. Avoid sources of humming (transformers, motors). To

prevent fire or electrical shock, do not expose this unit to rain or

water.

• Never open the cabinet. If something drops into the set, contact

your dealer.

• The voltage to be used must be the same as that specified on the

rear panel. Using this unit with a higher voltage than specified

is dangerous and may cause a fire and/or electric shock.

• To reduce the risk or fire or electric shock, do not expose this

unit to rain or moisture.

• Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and the

wires connected to other equipment. Never pull the wires

themselves.

• When not planning to use this unit for a long period (ie.,

vacation, etc.), disconnect the AC power plug from the wall

outlet.

• Since this unit has a built-in power amplifier, heat will radiate

from the rear panel. Place the unit apart from the walls, allowing

at least 20 cm of space above, behind and on both sides of the

unit to prevent fire or damage. Furthermore, do not position

with the rear panel facing down on the floor or other surfaces.

• Do not cover the rear panel of this unit with a newspaper, a

tablecloth, a curtain, etc. in order not to obstruct heat radiation.

If the temperature inside the unit rises, it may cause fire,

damage to the unit and/or personal injury.

• Do not place the following objects on this unit:

- Glass, china, small metallic etc.

If glass etc. falls by vibrations and breaks, it may cause bodily

injury.

- A burning candle etc.

If the candle falls by vibrations, it may cause fire and bodily

injury.

- A vessel with water in it

If the vessel falls by vibrations and water spills, it may cause

damage to the speaker, and/or you may get an electric shock.

• Do not place this unit where foreign objects such as water drips

might fall. It might cause a fire, damage to this unit, and/or

personal injury.

• Never put a hand or a foreign object into the YST port located

on the right side of this unit. When moving this unit, do not hold

the port as it might cause personal injury and/or damage to this

unit.

• Never place a fragile object near the YST port of this unit. If the

object falls or drops by the air pressure, it may cause damage to

the unit and/or personal injury.

• Never open the cabinet. It might cause an electric shock since

this unit uses a high voltage. It might also cause personal injury

and/or damage to this unit.

• When using a humidifier, be sure to avoid condensation inside

this unit by allowing enough spaces around this unit or avoiding

excess humidification. Condensation might cause a fire,

damage to this unit, and/or electric shock.

• Super-bass frequencies reproduced by this unit may cause a

turntable to generate a howling sound. In such a case, move this

unit away from the turntable.

• This unit may be damaged if certain sounds are continuously

output at high volume level. For example, if 20 Hz-50 Hz sine

waves from a test disc, bass sounds from electronic instruments,

etc. are continuously output, or when the stylus of a turntable

touches the surface of a disc, reduce the volume level to prevent

this unit from being damaged.

• If you hear distorted noise (i.e., unnatural, intermittent

“rapping” or “hammering” sounds) coming from this unit,

reduce the volume level. Extremely loud playing of a movie

soundtrack’s low frequency, bass-heavy sounds or similarly

loud popular music passages can damage this speaker system.

• Vibration generated by super-bass frequencies may distort

images on a TV. In such a case, move this unit away from the

TV set.

• Do not attempt to clean this unit with chemical solvents as this

might damage the finish. Use a clean, dry cloth.

• Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the unit is

faulty.

• Install this unit near the wall outlet and where the AC power

plug can be reached easily.

• Secure placement or installation is the owner’s

responsibility. Yamaha shall not be liable for any accident

caused by improper placement or installation of speakers.

CAUTION: Read this before operating your unit.

This unit features a magnetically shielded design, but

there is still a chance that placing it too close to a TV set

might impair picture color. Should this happen, move

this unit away from the TV set.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. In this state, this unit is designed

to consume a very small quantity of power.

1 En

English

SPECIAL INSTRUCTIONS FOR U.K. MODEL

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged

in a live socket outlet.

FEATURES .......................................................................................................................................................................2

SUPPLIED ACCESSORIES ...........................................................................................................................................2

PLACEMENT ..................................................................................................................................................................3

CONTROLS AND THEIR FUNCTIONS .....................................................................................................................4

CONNECTIONS ..............................................................................................................................................................6

[1] Connecting to line output (pin jack) terminals of the amplifier ..............................................................................6

[2] Connecting to speaker output terminals of the amplifier .........................................................................................8

Connecting to the INPUT1/OUTPUT terminals of the subwoofer .............................................................................10

Plug in the subwoofer to the AC outlet .......................................................................................................................11

ADJUSTING THE SUBWOOFER BEFORE USE ....................................................................................................12

AUTOMATIC POWER-SWITCHING FUNCTION .................................................................................................13

Changing the AUTO STANDBY setting ....................................................................................................................13

FREQUENCY CHARACTERISTICS .........................................................................................................................14

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II ..............................................................................15

TROUBLESHOOTING .................................................................................................................................................16

SPECIFICATIONS ........................................................................................................................................................17

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

For Canadian Customers

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

VOLTAGE SELECTOR

(For Asia and General models only)

The voltage selector switch on the rear panel of this unit must be set for your local main voltage BEFORE

plugging this unit into the AC main supply. Voltages are 110/120/220/230-240 V AC, 50/60 Hz.

CONTENTS

2 En

• This subwoofer system employs Advanced Yamaha

Active Servo Technology II, which Yamaha has

developed for reproducing higher quality super-bass

sound (refer to page 15 for details on Advanced Yamaha

Active Servo Technology II). This super-bass sound

adds a more realistic, theater-in-the-home effect to your

stereo system.

• This subwoofer can be easily added to your existing

audio system by connecting to either the speaker

terminals or the line output (pin jack) terminals of the

amplifier.

• For the effective use of the subwoofer, the subwoofer’s

super-bass sound should be matched to the sounds of

your main speakers. You can create the best sound

quality for various listening conditions by using the

HIGH CUT control and the PHASE switch.

• The Automatic power-switching function saves you the

trouble of pressing the STANDBY/ON button to turn the

power on and off.

• This subwoofer system is equipped with a linear port

unique to Yamaha that provides smooth bass response

during playback, minimizing extraneous noise not

included in the original input signal.

After unpacking, check that the following parts are

contained.

Non-skid pads (1 set: 4 pieces)

FEATURES SUPPLIED ACCESSORIES

3 En

English

( : subwoofer : main speaker)

One subwoofer will have a good effect on your audio

system, however, the use of two subwoofers is

recommended to obtain more effect.

If using one subwoofer, it is recommended to place it on

the outside of either the right or the left main speaker (see

A). If using two subwoofers, it is recommended to place

them on the outside of each main speaker (see B). The

placement shown in C is also possible, however, if the

subwoofer system is placed directly facing the wall, the

bass effect may die because the sound from it and the sound

reflected by the wall may cancel out each other. To prevent

this from happening, face the subwoofer system at an angle

as in A or B.

There may be a case that you cannot obtain enough

super-bass sounds from the subwoofer when listening in

the center of the room. This is because “standing waves”

have been developed between two parallel walls and

they cancel the bass sounds. In such a case, face the

subwoofer obliquely to the wall. It also may be

necessary to break up the parallel surfaces by placing

bookshelves etc. along the walls.

Use the non-skid pads

Put the provided non-skid pads at the four corners on the

bottom of the subwoofer to prevent the subwoofer from

moving by vibrations etc.

PLACEMENT

A

B

C

Note

4 En

1 POWER switch

Normally, set this switch to the ON position to use the

subwoofer. In this state, you can turn on the subwoofer

or turn the subwoofer into the standby mode by

pressing the STANDBY/ON switch.

2 OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the front speakers.

Signals from the INPUT1 terminals are sent to these

terminals.

(Refer to “CONNECTIONS” for details.)

3 INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

(Refer to “CONNECTIONS” for details.)

4 INPUT2 terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

5 AUTO STANDBY (OFF/LOW/HIGH) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described on page 13. If you do not need

this function, leave this switch in the OFF position.

Make sure to change the setting of this switch only when

the subwoofer is set in the standby mode by pressing the

STANDBY/ON switch.

6

PHASE (NORM/REV) switch

Normally, this switch is to be set to the REV (reverse)

position. However, according to your speaker systems

or the listening condition, there may be a case when

better sound quality is obtained by setting this switch

to the NORM (normal) position. Select the better

position by monitoring the sound.

CONTROLS AND THEIR FUNCTIONS

40Hz

140Hz

010

STANDBY/ON HIGH CUT

VOLUME

SUBWOOFER SYSTEM YST-RSW300

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

8

7

90

HIGH

OFF

LOW

NORM

REV

1

65

4

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

AUTO

STANDBY

PHASE

FROM AMPLIFIER

INPUT 1

2

3

R

L

R

Subwoofer rear panel

Subwoofer front panel

(U.S.A. model)

Note

5 En

CONTROLS AND THEIR FUNCTIONS

English

7

STANDBY/ON switch

Press this switch to turn on the power when the

POWER switch is set in the ON position (the status

indicator lights up in green). Press again to set the

subwoofer in the standby mode (the status indicator

goes off).

Even while the subwoofer is in the standby mode, it is

still using a small amount of power.

8

Status indicator

Lights up in green while the subwoofer is on.

Lights up in red while the subwoofer is set in the

standby mode by the operation of the automatic power-

switching function.

Goes off when the subwoofer is set in the standby

mode.

9

HIGH CUT control

Adjusts the high frequency cut off point. Frequencies

higher than the frequency selected by this control are

all cut off (and no output). One graduation of this

control represents 10 Hz.

0

VOLUME control

Adjusts the volume level. Turn the control clockwise to

increase the volume, and counterclockwise to decrease

the volume.

Note

6 En

Choose one of the following two connecting methods that is more suitable for your audio system.

■ Choose [1] (pages 6-7) if your amplifier has line output (pin jack) terminal(s)

■ Choose [2] (pages 8-9) if your amplifier has no line output (pin jack) terminal

Unplug the subwoofer and other audio/video components before making connections.

• All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to

the owner’s manual of your component to be connected to the subwoofer.

• After all connections are completed, plug in the subwoofer and other audio/video components.

• To connect with a Yamaha DSP amplifier (or AV receiver), connect the SUBWOOFER (or LOW PASS etc.) terminal

on the rear of the DSP amplifier (or AV receiver) to the /MONO INPUT2 terminal of the subwoofer.

• When connecting the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier, be sure to

connect the /MONO INPUT2 terminal to the “L” side and the INPUT2 terminal to the “R” side of the SPLIT

SUBWOOFER terminals.

• Some amplifiers have line output terminals labeled PRE OUT. When you connect the subwoofer to the PRE OUT

terminals of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier

has only one set of PRE OUT terminals, do not connect the subwoofer to the PRE OUT terminals. Instead, connect

the subwoofer to the speaker output terminals of the amplifier (refer to pages 8-9).

• When connecting to a monaural line output terminal of the amplifier, connect the /MONO INPUT2 terminal.

• When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT

terminals on the rear panel of the subwoofer. If connected, they will not produce sound.

CONNECTIONS

Caution

Notes

[1] Connecting to line output (pin jack) terminals of the amplifier

L

L R

Notes

L

7 En

CONNECTIONS

English

■ Using one subwoofer

■ Using two subwoofers

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

FROM AMPLIFIER

INPUT 1

R

L

R

Subwoofer

Amplifier

Mono pin cable

(not included)

Audio pin cable

(not included)

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

FROM AMPLIFIER

INPUT 1

FROM AMPLIFIER

INPUT 1

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

R

L

R

L

R

Amplifier

Mono pin cable (not included)

Mono pin cable

(not included)

Subwoofer Subwoofer

8 En

CONNECTIONS

Select this method if your amplifier has no line output (pin jack) terminal. For details about the connection method of the

INPUT1/OUTPUT terminals, see the “Connecting to the INPUT1/OUTPUT terminals of the subwoofer” on page 10.

If your amplifier has two sets of main speaker output terminals and both terminals can

output sound signals simultaneously:

• Connect one set of main speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and

connect the other set of main speaker output terminals of the amplifier to the main speakers.

• Set the amplifier so that both sets of main speaker output terminals output sound signals simultaneously.

If your amplifier has only one set of main speaker output terminals, see page 9.

■ Using one subwoofer (with speaker cables)

■ Using two subwoofers (with speaker cables)

[2] Connecting to speaker output terminals of the amplifier

Note

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

FROM AMPLIFIER

INPUT 1

R

L

R

Right speaker

Subwoofer Left speaker

Amplifier

Speaker

output

terminals

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

OUTPUT

TO SPEAKERS

/MONO

INPUT 1

FROM AMPLIFIER

INPUT

2

FROM AMPLIFIER

INPUT 1

R

L

R

L

R

Amplifier

Right speaker

Left speaker

Subwoofer

Speaker

output

terminals

9 En

CONNECTIONS

English

If your amplifier has only one set of main speaker output terminals:

Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the

OUTPUT terminals of the subwoofer to the main speakers.

■ Using one subwoofer (with speaker cables)

■ Using two subwoofers (with speaker cables)

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

FROM AMPLIFIER

INPUT 1

R

L

R

Right speaker

Left speaker

Subwoofer

Amplifier

Speaker output

terminals

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

FROM AMPLIFIER

INPUT 1

OUTPUT

TO SPEAKERS

/MONO

INPUT

2

FROM AMPLIFIER

INPUT 1

R

L

R

L

R

Right speaker Left speaker

Subwoofer

Speaker output

terminals

Amplifier

Subwoofer

10 En

CONNECTIONS

For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the

connections are faulty, no sound will be heard from the subwoofer or the speakers, or both of them. Make sure that the +

and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will

be unnatural and lack bass.

Do not let the bare speaker wires touch each other, because this could damage the

subwoofer or the amplifier, or both of them.

■ Before connecting

Remove the insulation coating at the extremity of each speaker cable by twisting the coating off.

■ How to connect

1 Press and hold the terminal’s tab, as shown in the figure below.

2 Insert the bare wire.

3 Release your finger from the tab to allow it to lock securely on the cable’s wire end.

4 Test the firmness of the connection by pulling lightly on the cable at the terminal.

Do not insert the insulation coating into the hole. The sound may not be produced.

Connecting to the INPUT1/OUTPUT terminals of the subwoofer

Caution

Good No Good

10mm

(3/8”)

2

1

Black: negative (–)

Red: positive (+)

Note

11 En

CONNECTIONS

English

After all connections are completed, plug in the subwoofer

and other audio/video components to the AC outlet.

■ VOLTAGE SELECTOR switch

(For Asia and General models only)

This unit has a voltage selector switch on the rear

panel. If the preset setting of the switch is incorrect,

set the switch to the proper voltage range (110/120/

220/230-240 V) of your area. Consult your dealer if

you are unsure of the correct setting.

Do not plug the subwoofer to the AC outlet before

setting the VOLTAGE SELECTOR.

Plug in the subwoofer to the AC outlet

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

To AC outlet

(U.S.A. model)

WARNING

VOLTAGE

SELECTOR

12 En

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer

and the main speakers by following the procedures described below.

1 Set the VOLUME control to minimum (0).

2 Turn on the power of all the other components.

3 Make sure that the POWER switch on the rear panel is

set to the ON position, then press the STANDBY/ON

switch on the front panel to turn on the subwoofer.

* The status indicator lights up in green.

4 Play a source containing low-frequency signals and

adjust the amplifier’s volume control to the desired

listening level.

5 Adjust the HIGH CUT control to the position where

the desired response can be obtained. Normally, set the

control to the level a little higher than the main

speaker’s rated minimum reproducible frequency*.

* The main speaker’s rated minimum reproducible

frequency can be looked up in the speakers’ catalog

or owner’s manual.

6 Increase the volume gradually to adjust the volume

balance between the subwoofer and the main speakers.

Normally, set the control to the level where you can

obtain a little more bass effect than when the

subwoofer is not used. If the desired response cannot

be obtained, adjust the HIGH CUT control and the

VOLUME control again.

7 Set the PHASE switch to the position which gives you

the better bass sound. Normally, set the switch to the

REV (reverse) position. If the desired response cannot

be obtained, set the switch to the NORM (normal)

position.

• Once the volume balance between the subwoofer and

the main speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control. However, if you change

the main speakers to others, you must make this

adjustment again.

• For adjusting the VOLUME control, the HIGH CUT

control and the PHASE switch, refer to

“FREQUENCY CHARACTERISTICS” on page 14.

ADJUSTING THE SUBWOOFER BEFORE USE

40Hz

140Hz

010

STANDBY/ON HIGH CUT

VOLUME

SUBWOOFER SYSTEM YST-RSW300

OUTPUT

TO SPEAKERS

INPUT

2

/MONO

LOW

AUTO

STANDBY

INPUT 1

FROM AMPLIFIER

POWER

ON

OFF

HIGH

NORM

REV

PHASE

NORM

REV

PHASE

3 5,6 1,6

3

7

Subwoofer rear panel

Subwoofer front panel

(U.S.A. model)

Notes

13 En

English

This function automatically switches the unit between standby and power-on modes.

- The subwoofer automatically places itself in standby mode if it does not receive an input signal for 7 or 8 minutes (the

status indicator lights red).

- When the subwoofer detects a bass signal input of below 200 Hz, it automatically places itself in power-on mode (the

status indicator lights green).

1 Set the subwoofer to standby.

2 Change the AUTO STANDBY setting.

- LOW: Normally select this position to activate this function.

- HIGH: If this function does not operate with AUTO STANDBY switch set to LOW, select this position so that the

subwoofer detects input signals with a lower level and switches the power on automatically.

- OFF: Select this position to deactivate this function, for example, when the subwoofer switches the power on

unexpectedly by sensing noises from other appliances.

• This function does not operate when the POWER switch is set to the OFF position, or when you manually set the

subwoofer to the standby mode by pressing the STANDBY/ON switch.

• Noise received from other appliances may extend the time period before the subwoofer places itself in the standby

mode to more than 8 minutes.

AUTOMATIC POWER-SWITCHING FUNCTION

Changing the AUTO STANDBY setting

Notes

14 En

This subwoofer’s frequency characteristics

The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer

is combined with a typical main speaker system.

■ Example 1

When combined with a 4” or 5” (10 cm or 13 cm) acoustic suspension, 2 way system main

speakers:

■ Example 2

When combined with an 8” or 10” (20 cm or 25 cm) acoustic suspension, 2 way system main

speakers:

*This diagram does not depict actual frequency response characteristics accurately.

FREQUENCY CHARACTERISTICS

(70Hz)

(REV)

(50Hz)

(REV)

20 50 100 200 500Hz

40

50

60

70

80

90

dB

HIGH CUT 40 Hz

HIGH CUT 90 Hz

HIGH CUT 140 Hz

40Hz

140Hz

010

HIGH CUT

VOLUME

PHASE

REVNORM

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-RSW300

Main

speaker

Frequency response graph*

40Hz

140Hz

010

HIGH CUT

VOLUME

PHASE

REVNORM

20 50 100 200 500Hz

40

50

60

70

80

90

dB

YST-RSW300

Main

speaker

Frequency response graph*

15 En

English

In 1988, Yamaha brought to the marketplace speaker

systems utilizing YST (Yamaha Active Servo Technology)

to give powerful, high quality bass reproduction. This

technique uses a direct connection between the amplifier

and speaker, allowing accurate signal transmission and

precise speaker control.

As this technology uses speaker units controlled by the

negative impedance drive of the amplifier and resonance

generated between the speaker cabinet volume and port, it

creates more resonant energy ( the “air woofer” concept)

than the standard bass reflex method. This allows bass

reproduction from much smaller cabinets than before.

Yamaha’s newly developed Advanced YST II adds many

refinements to Yamaha Active Servo Technology,

allowing better control of the forces driving the amplifier

and speaker. From the amplifier’s point of view, the

speaker impedance changes depending on the sound

frequency. Yamaha developed a new circuit design

combining negative-impedance and constant-current

drives, which provides a more stable performance and

clear bass reproduction without any murkiness.

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II

High-amplitude

bass sound

Port

Cabinet

Advanced impedance

Converter

Active

Servo

Processing

Amplifier

Signals of low amplitude

Air woofer (Helmholtz

resonator)

Signals

16 En

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instructions given below do not help, disconnect the power cord and contact your authorized Yamaha dealer or

service center.

TROUBLESHOOTING

Problem Cause What to Do

Power is not supplied even

though the STANDBY/ON switch

is set to the ON position.

The power plug is not securely

connected.

Connect it securely.

The POWER switch is set to the OFF

position.

Set the POWER switch to the ON

position.

No sound. The volume is set to minimum. Raise the volume up.

Speaker cables are not connected

securely.

Connect them securely.

Sound level is too low. Speaker cables are not connected

correctly.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to

“–”.

Setting of the PHASE switch is not

proper.

Set the PHASE switch to the other

position.

A source sound with few bass

frequencies is played.

Play a source sound with bass

frequencies. Set the HIGH CUT control

to a higher position.

It is influenced by standing waves. Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

The subwoofer does not turn on

automatically.

The POWER switch is set to the OFF

position.

Set the POWER switch to the ON

position.

The STANDBY/ON switch is set to the

STANDBY position.

Set the STANDBY/ON switch to the

ON position.

The AUTO STANDBY switch is set to

the OFF position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

The level of input signal is too low. Set the AUTO STANDBY switch to the

“HIGH” position.

The subwoofer does not turn into

the standby mode automatically.

There is an influence of noise generated

from external appliances etc.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables. Otherwise, set

the AUTO STANDBY switch to the

OFF position.

The AUTO STANDBY switch is set to

the OFF position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

The subwoofer turns into the

standby mode unexpectedly.

The level of input signal is too low. Set the AUTO STANDBY switch to the

“HIGH” position.

The subwoofer turns on

unexpectedly.

There is an influence of noise generated

from external appliances etc.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables. Otherwise, set

the AUTO STANDBY switch to the

OFF position.

17 En

English

Type ......Advanced Yamaha Active Servo Technology II

Driver ........................................25 cm (10”) cone woofer

Magnetic shielding type

Output Power .............. 250 W (100 Hz, 5 Ω 10% T.H.D)

Dynamic Power ............................................. 270 W, 5 Ω

Input Sensitivity (50 Hz, 250 W/5 Ω, L+R)

Speaker terminal .................................................. 1.0 V

RCA pin jack ..................................................... 50 mV

Input Impedance

Speaker terminal ................................................ 2.2 kΩ

RCA pin jack ...................................................... 12 kΩ

Frequency Response ................................ 20 Hz - 160 Hz

Power Supply

U.S.A. and Canada models ...............AC 120V, 60 Hz

U.K. and Europe models ...................AC 230V, 50 Hz

Australia model .................................AC 240V, 50 Hz

Asia and General models

........................AC 110/120/220/230-240 V, 50/60 Hz

Korea model ......................................AC 220V, 60 Hz

Power Consumption ................................................. 80 W

Standby Power Consumption .................................0.5 W

Dimensions (W x H x D)

...................................... 372 mm x 400 mm x 428 mm

(14-5/8” x 15-3/4” x 16-7/8”)

Weight ................................................20 kg (44 lbs. 1oz.)

* Please note that all specifications are subject to change

without notice.

SPECIFICATIONS

i Fr

Nous vous remercions d’avoir porté votre choix sur ce subwoofer de Yamaha.

Tenir compte des précautions ci-dessous avant de faire

fonctionner l’appareil. Yamaha ne saurait être tenue pour

responsable de tout dommage et/ou blessure dûs à un non-respect

des mises en garde ci-dessous.

• Pour garantir les meilleures performances possibles, lire ce

manuel avec attention. Le garder dans un endroit sûr

pour une utilisation ultérieure.

• Installer cette unité dans un endroit frais, sec et propre - loin des

fenêtres, sources de chaleur et d’endroits où les vibrations, la

poussière, l’humidité ou le froid sont importants. Eviter les

sources de bourdonnements (transformateurs, moteurs). Pour

éviter les incendies ou les électrocutions, ne pas exposer cette

unité à la pluie ni à l’humidité.

• Ne jamais ouvrir le boîtier. Si quelque chose tombe dedans,

contacter immédiatement le revendeur.

• La tension à utiliser doit être la même que celle spécifiée sur le

panneau arrière. Utiliser cet appareil avec une plus haute

tension que celle spécifiée est dangereux et peut causer un

incendie et/ou causer une électrocution.

• Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas

exposer cet appareil à la pluie ni à l’humidité.

•N

e pas forcer les commutateurs, les touches ou les câbles de

raccordement. Lors du déplacement de l’appareil, d’abord débrancher

la prise d’alimentation et les câbles le raccordant à d’autres appareils.

Ne jamais tirer sur les cordons.

• Lorsqu on prévoit de ne pas utiliser cet appareil pendant

longtemps (pendant les vacances, par exemple), débrancher le

cordon d’alimentation CA de la prise murale.

• Cet appareil possédant un amplificateur intégré, de la chaleur

sera irradiée par le panneau arrière. Placer l’unité assez loin des

murs, en laissant toujours un espace de 20 cm au moins au-

dessus, au-dessous et des deux côtés de l’unité afin d’éviter les

risques d’incendie et de dommages. Ne pas positionner non plus

cet appareil dos au plancher ou à une autre surface.

• Ne couvrez pas le panneau arrière de cet appareil avec un journal, une

nappe, un rideau, etc. afin de ne pas empêcher la dissipation de

chaleur. Si la température à l’intérieur de cet appareil augmente, un

incendie peut se déclarer et endommager cet appareil et/ou causer une

blessure corporelle.

• Ne jamais placer les objets suivants sur cette unité :

- Des objets verres, de la vaissille, des petits objets metalliques,

etc.

Des blessures pourraient être causées par des débris de verre,

etc. dûs aux vibrations et aux brisures.

- Une bougie allumée, etc.

Si la bougie tombe sous l’effet des vibrations, elle risque de

provoquer un incendie et des blessures corporelles

.

- Un récipient contenant de l’eau

Si le récipient tombe sous l’effet des vibrations et que de l’eau

éclabousse l’enceinte, ceci risque de l’endommager

sérieusement, et/ou de provoquer des électrocutions.

• Ne pas mettre cette unité dans les endroits où des corps

étrangers, comme des jets d’eau par exemple, pourraient tomber

dedans. Ceci pourrait causer un incendie, endommager cette

unité, et/ou des blessures corporelles.

• Ne jamais introduire la main ou un corps étranger dans le port YST

situé sur le côté droit de cette unité. Ne jamais attraper l’unité par

l’orifice du port lors des déplacements, car ceci pourrait causer des

blessures corporelles et/ou endommager l’unité.

• Ne jamais placer un objet fragile à proximité du port YST de

cette unité. Si cet objet venait à chuter en raison de la pression

de l’air, il pourrait endommager l’unité et/ou causer des

blessures corporelles.

• Ne jamais ouvrir le boîtier. Ceci pourrait entraîner des

électrocutions, car cette unité fonctionne sous haute tension.

Ceci pourrait aussi causer des blessures corporelles et/ou

endommager l’unité.

• En utilisant un humidificateur, éviter la condensation à l’intérieur

de l’appareil en libérant la place autour de l’appareil ou en évitant

l’humidification extrême. La condensation peut causer un feu,

des dommages à l’appareil et/ou une électrocution.

• Les sons de très basse fréquence produits par cet appareil

peuvent provoquer un sifflement sur le tourne-disque. Dans ce

cas, éloigner cet appareil du tourne-disque.

• Cet appareil peut être endommagé si certains sons sont

continuellement émis à un niveau sonore élevé. Par exemple, si

des ondes sinusoïdales de 20 Hz-50 Hz d’un disque d’essai, des

sons de graves d’instruments électroniques, etc. sont émis en

continu ou si la pointe de lecture d’une platine tourne-disque

touche la surface d’un disque, réduire le niveau de volume pour

éviter d’endommager cet appareil.

• Si une distorsion se fait entendre (par exemple des petits coups

secs intermittents ou un “martèlement”) sur cet appareil,

diminuer le niveau sonore. La lecture à très haut volume des

sons de basse ou des sons de basses fréquences de la bande

sonore d’un film, ou de passages de musique pop de forte

intensité, sont susceptibles d’endommager ce système

d’enceintes.

• Des vibrations générées par des fréquences supergraves

risquent de déformer les images sur un téléviseur. Dans ce cas,

éloigner cet appareil du téléviseur.

• Ne pas essayer de nettoyer cette unité avec des diluants

chimiques, ceci endommagerait le fini. Utiliser un chiffon

propre et sec.

•B

ien lire la section “RESOLUTION DES PROBLEMES”

concernant les erreurs de fonctionnement communes avant de

conclure que l’unité est défecteuse.

• Installez cet appareil à proximité de la prise secteur et à un

emplacement où la fiche du câble d’alimentation est facilement

accessible.

• Le propriétaire du système est entièrement responsable du

bon positionnement et de la bonne installation du système.

Yamaha décline toute responsabilité en cas d’accident causé

par un positionnement ou une installation inadéquats des

enceintes.

ATTENTION : Tenir compte des précautions ci-dessous

avant de faire fonctionner l’appareil.

Même si cette unité dispose d’une conception à blindage

magnétique, il y a un risque possible de création

d’interférences, visibles sur les images en couleurs si elle est

placée à côté d’un téléviseur. Dans ce cas, éloigner l’unité du

téléviseur.

Cet appareil n’est pas déconnecté du secteur tant qu’il reste

branché á la prise de courant. En pareil cas, celui-ci

consomme une faible quantité d’électricité.

Pagina se încarcă ...

Yamaha YST-RSW300 Manualul proprietarului

Yamaha YST-RSW300 Manualul proprietarului

în alte limbi

Lucrări conexe