WARNING
IN ORDER TO AVOID ELECTRIC SHOCK OR OTHER POSSIBLE INJURY:
• DO NOT USE THIS PRODUCT FOR HUMAN SAFETY APPLICATIONS. IT
WAS NOT DESIGNED, TESTED, OR RECOMMENDED FOR THIS USE.
• DO NOT USE THIS PRODUCT IN HAZARDOUS LOCATIONS (E.G.
EXPLOSIVE ATMOSPHERES). IT WAS NOT DESIGNED, TESTED, OR
RECOMMENDED FOR THIS USE.
• ENSURE THE PRODUCT IS PROPERLY WIRED TO THE CORRECT POWER
SUPPLY FOR THE APPLICATION. REFER TO THE SPECIFICATIONS AND
WIRING DIAGRAMS IN THIS PUBLICATION.
Models Covered In This Publication
C7atalog
Number
Description
EDC205SP Split Core, 24 VAC/DC, 0-5 0 VDC Output, 50/75/100 A Range
EDC305SP Split Core, 24 VAC/DC, 0-5 VDC Output, 100/150/200 A Range
EDC405SP Split Core, 24 VAC/DC, 0-5 VDC Output, 150/225/300 A Range
EDC210SP Split Core, 24 VAC/DC, 0-10 VDC Output, 50/75/100 A Range
EDC310SP Split Core, 24 VAC/DC, 0-10 VDC Output, 100/150/200 A Range
EDC410SP Split Core, 24 VAC/DC, 0-10 VDC Output, 150/225/300 A Range
EDC2420SP Split Core, 24 VAC/DC, 4-20 mA Output, 50/75/100 A Range
EDC3420SP Split Core, 24 VAC/DC, 4-20 mA Output, 100/150/200 A Range
EDC4420SP Split Core, 24 VAC/DC, 4-20 mA Output, 150/225/300 A Range
CurrentWatch™ EDC Series Current Sensors
DC Current Sensor, Split Core Housing with
Analog Output
Instructions Publication P51927
Effective July 2017
Supersedes March 2014
Instruction Leaflet
Montageanweisung
Notice d’installation
Instrucciones de montaje
Istruzioni per il montaggio
安装说明
Инструкция по монтажу
Montagehandleiding
Montagevejledning
Οδηγίες εγκατάστασης
Instruções de montagem
Monteringsanvisning
Asennusohje
Návod k montáži
Paigaldusjuhend
Szerelési utasítás
Montāžas instrukcija
Montavimo instrukcija
Instrukcja montażu
Navodila za montažo
Návod na montáž
Монтажни инструкции
Instrucţiuni de montaj
Upute za montažu
Electric current! Danger to life!
Only skilled or instructed persons may
carry out the following operations.
Lebensgefahr durch elektrischen Strom!
Nur Elektrofachkräfte und elektrotechnisch
unterwiesene Personen dürfen die im Folgenden
beschriebenen Arbeiten ausführen.
Tension électrique dangereuse !
Seules les personnes qualifiées et averties doivent
exécuter les travaux ci-après.
¡Corriente eléctrica! ¡Peligro de muerte!
El trabajo a continuación descrito debe ser realizado
por personas cualificadas y advertidas.
Tensione elettrica: Pericolo di morte!
Solo persone abilitate e qualificate possono eseguire
le operazioni di seguito riportate.
触电危险！
只允许专业人员和受过专业训练的人员进行下列工作。
Электрический ток! Опасно для жизни!
Только специалисты или проинструктированные
лица могут выполнять следующие операции.
Levensgevaar door elektrische stroom!
Uitsluitend deskundigen in elektriciteit en
elektrotechnisch geïnstrueerde personen is het
toegestaan, de navolgend beschreven
werkzaamheden uit te voeren.
Livsfare på grund af elektrisk strøm!
Kun uddannede el-installatører og personer der
e instruerede i elektrotekniske arbejdsopgaver,
må udføre de nedenfor anførte arbejder.
en
de
fr
es
it
zh
ru
nl
da
Προσοχή, κίνδυνος ηλεκτροπληξίας!
Οι εργασίες που αναφέρονται στη συνέχεια θα
πρέπει να εκτελούνται μόνο από ηλεκτρολόγους
και ηλεκτροτεχνίτες.
Perigo de vida devido a corrente eléctrica!
Apenas electricistas e pessoas com formação
electrotécnica podem executar os trabalhos
que a seguir se descrevem.
Livsfara genom elektrisk ström!
Endast utbildade elektriker och personer som
undervisats i elektroteknik får utföra de arbeten
som beskrivs nedan.
Hengenvaarallinen jännite!
Vain pätevät sähköasentajat ja opastusta saaneet
henkilöt saavat suorittaa seuraavat työt.
Nebezpečí úrazu elektrickým proudem!
Níže uvedené práce smějí provádět pouze
osoby s elektrotechnickým vzděláním.
Eluohtlik! Elektrilöögioht!
Järgnevalt kirjeldatud töid tohib teostada ainult
elektriala spetsialist vői elektrotehnilise
instrueerimise läbinud personal.
Életveszély az elektromos áram révén!
Csak elektromos szakemberek és elektrotechnikában
képzett személyek végezhetik el a következőkben leírt
munkákat.
Elektriskā strāva apdraud dzīvību!
Tālāk aprakstītos darbus drīkst veikt tikai
elektrospeciālisti un darbam ar elektrotehniskām
iekārtām instruētās personas!
el
pt
sv
fi
cs
et
hu
lv
Pavojus gyvybei dėl elektros srovės!
Tik elektrikai ir elektrotechnikos specialistai gali
atlikti žemiau aprašytus darbus.
Porażenie prądem elektrycznym stanowi
zagrożenie dla życia!
Opisane poniżej prace mogą przeprowadzać tylko
wykwalifikowani elektrycy oraz osoby odpowiednio
poinstruowane w zakresie elektrotechniki.
Življenjska nevarnost zaradi
električnega toka!
Spodaj opisana dela smejo izvajati samo
elektrostrokovnjaki in elektrotehnično poučene osebe.
Nebezpečenstvo ohrozenia života
elektrickým prúdom!
Práce, ktoré sú nižšie opísané, smú vykonávat’
iba elektroodborníci a osoby s elektrotechnickým
vzdelaním.
Опасност за живота от електрически ток!
Операциите, описани в следващите раздели,
могат да се извършват само от
специалисти-електротехници и инструктиран
електротехнически персонал.
Atenţie! Pericol electric!
Toate lucrările descrise trebuie efectuate numai
de personal de specialitate calificat şi de persoane
cu cunoştiinţe profunde în electrotehnică.
Opasnost po život uslijed električne struje!
Radove opisane u nastavku smiju obavljati samo
stručni električari i osobe koje su prošle
elektrotehničku obuku.
lt
pl
sl
sk
bg
ro
hr
292004059
Introduction
The CurrentWatch™ EDC Series
combines a hall effect sensor and a
signal conditioner into a single, compact
package for use in DC current applica-
tions up to 300 A. The EDC Series has
jumper selected current input ranges and
industry standard outputs: 4-20 mA,
0-5 VDC and 0-10 VDC. Split core models provide for quick and easy
installation.
ote:N This manual only covers split-core versions of the EDC Series. For the
solid-core manual, use publication P51926.
Eaton’s current sensor family encompasses a broad range of prod-
ucts for cost-effective monitoring, status, and predictive mainte-
nance. Downtime and costly repairs can be avoided by utilizing
Eaton’s products and technologies in your control systems.
Quick Install Guide
The below steps can be followed to quickly install a CurrentWatch
EDC Series sensor.
1. Run the wire to be monitored through the aperture, being sure
monitored current flow matches arrows on the sensor.
2. Mount the sensor to a surface if needed.
3. Connect output wiring:
a. Use up to 14 AWG copper wires, tightening terminals to
4 in.-lbs / 0.45 N·m maximum of torque,
b. For current output models (4-20 mA), make sure output load
is no more than 800 ohms,
c. For voltage output models (0-5/0-10 VDC), make sure output
load is at least 10 kilohms.
4. Connect power using the appropriate power supply.
5. Select range by positioning the Range Jumper.
Installation
Considerations for all EDC Series models…
•
Run wire to be monitored through the aperture (opening) of the
sensor.
•
Be sure monitored current flows in the same direction as the
arrow on the sensor (the arrow is located just above the hinge,
with a plus symbol on the left and a minus symbol on the right).
•
These switches can be located in the same environment as
motors, contactors, heaters, pull-boxes, and other electrical enclo-
sures.
•
Mounting can be done in any position or hung directly on a wire
with a wire tie.
•
Be sure to leave at least one in.(2.54 mm) distance between sen-
sor and other magnetic devices.
•
Press the tab in the direction
shown in the diagram to the right.
•
After placing the wire in the
aperture, press the hinged portion
firmly downward until a click is
heard and the tab pops out fully.
•
Keep split-core contact areas
clean. Silicon grease is factory applied on the mating surfaces to
prevent rust and improve performance. Be careful not to allow
grit or dirt into the grease in the contact area, particularly on core
mating surfaces of split core models. Sensor operation could
be impaired if mating surfaces do not have good contact. Check
visually before closing.
To open:
Press tab inward
towards hinge
Important:
Keep contact areas clean
Range Selection
The CurrentWatch EDC Series sensors feature field selectable rang-
es. The ranges are factory calibrated, eliminating time consuming
and inaccurate field setting of zero or span.
Setting Range
1. Determine the normal operating amperage of your monitored
current.
2. Select the range this is equal to or slightly higher than the nor-
mal operating amperage.
3. Place the Range Jumper in the appropriate position.
Output Wiring
Connect control or monitoring wires to the sensor. Use up to 14
AWG copper wire and tighten terminals to 4 in.-lbs / 0.45 N·m maxi-
mum torque.
Connection Notes:
•
For current output models, the current loop is powered by the
sensor. Maximum loop impedance is 800 ohms.
•
For voltage output models, the signal is powered by the sensor.
Minimum output load (impedance) is 10 kilohms.
•
Deadfront captive screw terminals.
•
Use 12-22 AWG solid or stranded.
•
Remove jumper entirely for Low Range operation.
•
Observe polarity.
Troubleshooting
Problem
Solution for Current
Output Models (4-20 mA)
Solution for Voltage
Output Models (0-5/0-
10 VDC)
Sensor has no
output.
Monitored load is not DC or is not on. Check that the moni-
tored load is DC and that it is actually on.
Polarity is not properly matched. Check and correct wiring
polarity.
For split core models, the core contact area may be dirty. Open
the sensor and clean the contact area.
Output signal is
too low.
The jumper may be set in a range that is too high for current
being monitored. Move jumper to the correct range.
Power supply is inadequate. Check power supply. Make sure
it is of sufficient voltage with all loads at maximum. The cur-
rent draw of EDC Series sensors is 2.0 VA.
Output load is too high.
Check output load, being sure
it is no more than 800 ohms.
Output load is too low. Check
output load, making sure it is
at least 10 kilohms.
Output signal is
always at
maximum.
The jumper may be set in a range that is too low for current
being sensed. Change the jumper position.
Power Supply
(22-38V AC/DC)
(-)
(+)
(+)(-)
1 (-) 2 (+) 3 (-) 4 (+)
Power Output
Mid
High
Range
Jumper
Load
(Controller, Meter...)
2
EATON www.eaton.com
CurrentWatch™ EDC Series Current Sensors
DC Current Sensor, Split Core Housing with
Analog Output
Instructions Publication P51927
Effective July 2017
Output Polarity
-Amps 0 + Amps
100%
50%
0%
Unipolar
(Magnitude Only)
O
U
T
P
U
T
Specications
Specification Value
Power Supply 24 VAC/DC (22-38 VAC/DC)
Power input and output signal are not isolated.
Caution: Do not connect Grounded AC Supply to the
Output Negative (-), as sensor damage may occur.
Power Consumption 2 VA
Current Ranges Selectable by Model: 50, 75, 100, 150, 200, 225, 300 A
Output Signal Unipolar: 0-20 mA, 4-20 mA, 0-5 VDC or 0-10 VDC
Output Polarity Unipolar: Current Magnitude Only
Response Time 100 ms (90% of Step Change)
Repeatability 1% FS
Frequency Range DC
Accuracy 1% FS
Linearity 0.75%
Isolation Voltage 3 kV (Monitored Line to Output)
Sensing Aperture 0.85 in. (21.7 mm) sq.
Housing UL94 V0 Flammability Rated
Environmental Operating Temperature: -4 to +122°F (-20 to +50°C)
Humidity: 0-95% RH, Non-Condensing
Temperature Drift 0.01% / Degree C
Approvals UL Listed, E117028
UL tested to Canadian safety standards
CE
RoHs Compliant
3
EATON www.eaton.com
Instructions Publication P51927
Effective July 2017
CurrentWatch™ EDC Series Current Sensors
DC Current Sensor, Split Core Housing with
Analog Output
Eaton Industries GmbH
Hein-Moeller-Straße 7-11,
53115 Bonn, Germany
Eaton Corporation
W126 N7250 Flint Drive
Menomonee Falls,
WI 53051, USA
Contact your regional Eaton oce for additional technical support
Eaton is a registered trademark of
Eaton Corporation.
All other trademarks are property
of their respective owners.
Americas – Asia Pacic Europe – Middle East – Africa
Eaton Corporation
Electrical Sector – Sensors
+1.800.426.9184
www.eaton.com/sensors
Eaton Industries GmbH
Electrical Sector EMEA
+49 (0) 180 5 223822
www.eaton.eu/sensors
© 2017 by Eaton
All Rights Reserved
Printed in USA
Publication No. P51927 / 003
July 2017
CurrentWatch™ EDC Series Current Sensors
DC Current Sensor, Split Core Housing with
Analog Output
Instructions Publication P51927
Effective July 2017
Eaton Industries GmbH
Hein-Moeller-Straße 7-11,
53115 Bonn, Germany
Eaton
W126 N7250 Flint Drive
Menomonee Falls,
WI 53051, USA
Eaton
Electrical Sector – Sensors
+1.800.426.9184
www.eaton.com/sensors
Eaton Industries GmbH
Electrical Sector EMEA
+49 (0) 180 5 223822
www.eaton.eu/sensors
Eaton is a registered trademark.
All other trademarks are property
of their respective owners.
Contact your regional Eaton office for additional technical support
Americas – Asia Pacific Europe – Middle East – Africa
-
1
-
2
-
3
-
4
Eaton CurrentWatch EDC series - split core housing Manualul proprietarului
- Tip
- Manualul proprietarului
- Acest manual este potrivit și pentru
în alte limbi
Lucrări conexe
-
Eaton CurrentWatch EAC series 120 Vac or 24 Vac/DC, 4-20 mA output Manualul proprietarului
-
-
-
-
-
-
-
-
-